Range Rover Classic. Manual — part 174
WIPERS AND WASHERS
3
REPAIR
HEATED WINDSCREEN WASHER JETS
THERMOSTAT
Service repair no - 84.10.12.
The thermostat is located on right headlamp mounting
panel.
Remove
1. Disconnect battery negative lead.
2. Remove radiator grill.
See CHASSIS AND
BODY, Repair, Radiator Grille
3. Remove two screws securing thermostat to right
hand headlamp mounting panel.
4. Withdraw thermostat, disconnecting electrical
connector.
Refit
5. Reverse removal procedure.
WINDSCREEN WASHER TUBES
Service repair no - 84.10.15.
Remove
1. Disconnect tubing from reservoir pump.
2. Disconnect tubing from washer jets.
3. Disconnect tubing from three-way tee piece.
4. Release tubing from edge clips.
Refit
5. Reverse removal procedure.
84
WIPERS AND WASHERS
4
REPAIR
WIPER ARMS - WINDSCREEN
Service repair no - 85.15.01
Remove
1. Hold back small spring clip which retains wiper
arm on shaft boss using a suitable tool.
2. Gently pry off wiper arm from shaft boss.
Refit
3. Allow motor to move to ’park’ position.
4. Push arm on to boss, locating it on splines so
that wiper blades are clear of screen rail.
5. Ensure that spring retaining clip is located in
retaining groove on shaft boss.
6. Operate wiper on a wet screen to ensure blades
do not over travel.
WIPER ARM - TAILGATE
Service repair no - 84.35.01.
Remove
1. Lift wiper arm end cap to access wiper motor
shaft.
2. Remove wiper arm securing nut.
3. Withdraw wiper arm from shaft.
Refit
4. Allow motor to move to ’park’ position.
5. Fit wiper arm to shaft,locating it on the splines so
that wiper blade is clear of screen surround.
6. Fit and tighten securing nut.
7. Push end cap back into position.
8. Check correct operation of wiper.
WIPERS AND WASHERS
5
REPAIR
WIPER BLADES - WINDSCREEN AND TAILGATE
Service repair no - 84.15.05.
Remove
1. Pull wiper arm away from glass.
2. Lift spring clip and withdraw blade from arm.
Refit
3. Reverse removal procedure.
WINDSCREEN WIPER MOTOR, LINKAGE AND
WHEEL BOXES
Service repair no - 84.15.12.
Remove
1. Disconnect battery negative lead. Remove wiper
arms.
2. Remove locknuts from wheel boxes.
3. Remove grommet from wheel boxes.
4. Remove bonnet[hood].
See CHASSIS AND
BODY, Repair, Bonnet
5. Remove front decker[cowl] panel.
See
CHASSIS AND BODY, Repair, Decker Panel
84
WIPERS AND WASHERS
6
REPAIR
6. Remove spring clips securing primary links to
wheelbox shaft links.
7. Remove spring clips securing primary links to
motor crank.
8. Remove primary links.
9. Remove lower grommet from wheelboxes.
10. Remove screw securing bonnet[hood] torsion
bar bracket. Unclip bracket from torsion bar.
11. Remove remaining screws securing motor and
linkage assembly to bulkhead.
12. Ease unit from mounting location and disconnect
electrical leads at plug and socket.
13. Withdraw unit.
14. Remove three bolts securing motor to mounting
plate.
15. Separate motor from mounting plate by pulling
motor crank through grommet.
Refit
16. Reverse removal procedure.
17. Ensure primary links are mounted with bushes
on inside, towards wiper motor. The shorter
primary link is mounted on driver side.
18. Replace front decker[cowl] panel.
19. Replace bonnnet.
20. Replace wiper arms.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст