Range Rover Classic. Manual — part 180
86
ELECTRICAL
8
REPAIR
HEADLAMP ALIGNMENT
Service repair no - 86.40.17
Headlamp beam setting should only be carried out by
qualified personnel using suitable beam setting
equipment, for example the Lucas Beamtester.
RR3825M shows right hand drive beam pattern, left
hand drive is symetrically opposite.
Guide to beam pattern:
1. Maximum intensity zone.
2. Beam aim kink point.
3. Aiming datum lines.
Adjust
1. Turn top adjusting screw anti-clockwise to lower
beam, clockwise to raise beam.
2. Turn side adjusting screw anti-clockwise to move
beam to left, clockwise to move beam to right.
AUXILIARY DRIVING LAMP
Service repair no - 86.40.96
Bulb replacement
1. Disconnect battery negative lead.
2. Securing nut is located beneath front bumper,
adjacent to front body fixing. Access to lamp is
gained through front wheel arch.
3. Disconnect electrical plug.
4. Remove single nut and washer.
5. From front of vehicle, manoeuvre lamp. Remove
lamp from spoiler opening.
6. Remove two screws securing cover to rear of
lamp.
7. Withdraw cover.
8. Disconnect lucar connector.
9. Release spring clip securing bulb to lamp unit.
10. Remove bulb.
ELECTRICAL
9
REPAIR
Refit
11. Fit a new bulb. Ensure two notches on bulb body
locate with registers on lamp unit.
12. Reverse removal procedure.
Adjust
Correct adjustment is beam horizontal (parallel to
ground) and parallel to vehicle axis.
13. Loosen lamp adjusting bolt to lower or raise
beam.
14. Loosen lamp securing bolt to move beam to left
or right.
15. Tighten fixing bolts to
15 Nm.
SIDELIGHT AND FLASHER LAMP ASSEMBLY
AND BULB
Service repair no - 86.40.24
Remove
1. Disconnect battery negative lead.
2. Remove two screws and plain washers securing
lamp assemly.
3. Lift assembly away sufficiently to gain access to
rear of lamp.
4. Remove waterproof cover.
5. Depress two retaining clips and withdraw bulb
holder.
6. Remove required bulb. Direction indicator bulb is
located in upper section of bulb holder, side
lamp bulb in lower.
7. Disconnect multi-plug. Remove complete
assembly.
Refit
8. Reverse removal procedure. Ensure waterproof
cover is correctly located.
86
ELECTRICAL
10
REPAIR
DIRECTION INDICATOR/SIDE REPEATER LAMP
BULB REPLACEMENT
Service repair no - 86.40.65
Remove
1. Disconnect battery negative lead.
2. Release clips securing wheel arch liner.
3. At back of lamp, twist bulb holder anti-clockwise
to remove from lamp assembly.
4. Remove bulb.
Refit
5. Reverse removal procedure.
TAIL LAMP ASSEMBLY
Service repair no - 86.40.74
Remove
1. Disconnect battery negative lead.
2. Remove four lens retaining screws.
3. Remove lens.
4. Remove sealing rubber, if required.
NOTE: To remove sealing rubber complete
it is necessary to remove side marker lens.
5. Remove bulbs.
6. Remove four screws securing lamp unit to body.
7. Remove two through-screws from reflector side,
which also secure lamp unit to body.
8. Ease lamp unit forward and disconnect leads at
moulded connectors.
Refit
9. Reverse removal procedure.
ELECTRICAL
11
REPAIR
REFLECTORS/SIDE MARKER LAMP ASSEMBLY
AND BULB
Service repair no - 86.40.67
Remove
1. Remove four screws securing lens.
2. Remove lens.
3. Remove bulb.
NOTE: To remove rubber seal completely
it is necessary to remove tail light lens.
Refit
4. Reverse removal procedure.
UNDER BONNET LAMP ASSEMBLY
Service repair no - 86.45.24
Remove
1. Disconnect battery negative lead.
2. Remove two securing screws.
3. Remove lamp glass.
4. Pull ’wedge’ type bulb from bulb holder.
5. Disconnect electrical leads located below bonnet
lamp switch attached to inner fender.
6. Pull rubber grommet off leads and pull lamp and
leads up through hood stiffener channel.
Refit
7. Reverse removal procedure. 1 to 6.
NOTE: A piece of bent wire will be needed
to pull electrical leads out of channel exit
hole when fitting a new lamp assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст