Range Rover Sport. Manual — part 36
CAUTION: Ensure the ball joint seal is not damaged. A damaged seal will lead to the premature
failure of the joint.
Connect the lower arm to the wheel knuckle.
Tighten the bolt to 175 Nm (129 lb.ft).
4 . Install a new halfshaft retaining nut and lightly tighten.
5 . Secure the parking brake cable.
6
.
CAUTION: Do not use a bolt that has been installed more than 5 times. Check the bolt head for
centre punch marks. A bolt head with 4 centre punch marks indicates the bolt has been installed 5 times
and must be replaced.
Connect the toe link.
Tighten the bolt to 175 Nm (129 lb.ft).
Mark the bolt head with a centre punch, to indicate the number of times it has been used.
7 . Tighten the halfshaft retaining nut to 350 Nm (258 lb.ft).
Stake the nut to the halfshaft.
8 . Install the wheel and tire.
9 . Carry out the wheel alignment procedure.
Toe Link (64.35.70)
Removal
1
.
WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle
on safety stands.
Raise and support the vehicle.
2 . Remove the wheel and tire.
3 . Disconnect the toe link.
Remove and discard the bolt.
4 . Remove the toe link.
Remove and discard the nut.
Installation
1
.
CAUTION: Make sure the toe link anti-rotation tang is fully seated in the integrated body frame
before tightening the toe link retaining nut. Failure to follow this instruction will result in damage to the toe
link or integrated body frame.
Install the toe link.
Install a new nut and lightly tighten.
2
.
Connect the toe link.
Using a M14 x 2 tap, clean the threads of the knuckle fixing hole. Blow out debris with an air-
line.
Tighten the new bolt to 175 Nm (129 lb.ft).
3
.
Set the gap, between the underside of the toe link rubber boot and the integrated body frame bracket, to 15 mm
(0.590 in).
Tighten the toe link inner ball joint retaining nut to 133 Nm (98 lb.ft)
Tighten the wheel nuts to 140 Nm (103 lb.ft).
5 . Carry out the wheel alignment procedure.
Specifications
Wheels
Wheel type
Wheel size
Alloy wheel
7J x 17
Alloy wheel
8J x 18
Alloy wheel
8J x 19
Alloy wheel
9J x 19
Alloy wheel
9.5J x 20
Reduced size spare wheel - Steel 5.5J x 19
CAUTION: With reduced size spare wheel installed, do not exceed 50 mph (80 kph) and replace with
standard size wheel at earliest opportunity.
CAUTION: Do not use power tools when operating the spare wheel winch, raise and lower winch manually
using hand tools only.
Tire Sizes - Standard Fit
Wheel size
Tire size
Tire load index
7J x 17 - Alloy
235/65 R17H - All terrain 108
8J x 18 - Alloy
255/55 R18V - All terrain 109
8J x 19 - Alloy
255/50 R19Y - All terrain 107
9J x 19 - Alloy
255/50 R19Y - All terrain 107
9.5J x 20 - Alloy 275/40 R20M - All terrain 106
CAUTION: Inner tubes must not be installed with any of these tires.
Tire Pressures - Not NAS Vehicles
Loading condition
bar lb/in² kPa
Normal operating conditions - Up to 4 people:
Front
2.3 34
230
Rear
2.5 36
250
Vehicle loaded to maximum gross vehicle weight:
Front
2.6 38
260
Rear
2.9 42
290
Reduced size spare wheel
4.2 60
420
* Standard size spare wheel
2.9 42
290
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст