Range Rover Sport. Manual — part 61
C1B1903
Door status
signal, pulse
width
modulated
failures
Incorrect software
loaded to air
suspension control
module
Central junction box
to air suspension
module harness
wiring: short circuit
to ground, short
circuit to power, high
resistance
Central junction box
fault
Refer to the guided diagnostic routine for this code on the
approved diagnostic system.
C1B211C
Compressor
brush card
temperature
sensor circuit,
voltage out of
range
Compressor brush
card temperature
sensor harness
wiring: short circuit
to ground, short
circuit to power, high
resistance
Compressor brush
card temperature
sensor failure
Air suspension
control module
failure
Refer to the guided diagnostic routine for this code on the
approved diagnostic system. Refer to the warranty policy and
procedures manual if a module is suspect.
U007388
CAN bus fault,
bus off
CAN bus
connections short
circuit to each other
Communications Network
U010087
Lost
communication
with engine
control module
(ECM)
CAN bus fault
ECM disconnected
ECM not configured
ECM failure
Communications Network
U010187
Lost
communication
with
transmission
control module
(TCM)
CAN bus fault
TCM disconnected
TCM not configured
TCM failure
Communications Network
U010287
Lost
communication
with transfer
box control
module
CAN bus fault
Transfer box control
module
disconnected
Transfer box control
module not
configured
Transfer box control
module failure
Communications Network
U012287
Lost
communication
with ABS
module
CAN bus fault
ABS module
disconnected
ABS module not
configured
ABS module failure
Communications Network
Lost
communication
with steering
angle sensor
(SAS) module
CAN bus fault
SAS module
disconnected
SAS module not
configured/calibrated
SAS module failure
Communications Network
U012887
Lost
communication
with parking
brake module
CAN bus fault
Parking brake
module
disconnected
Parking brake
module not
configured
Parking brake
module failure
Communications Network
U013387
Lost
communication
with active
stabilization
system
CAN bus fault
Active stabilization
system module
disconnected
Active stabilization
system module not
configured
ABS module failure
Communications Network
U013687
Lost
communication
with electronic
rear differential
control module
CAN bus fault
Electronic rear
differential control
module
disconnected
Electronic rear
differential control
module not
configured
Electronic rear
differential control
module failure
Communications Network
U015587
Lost
communication
with
instrument
cluster
CAN bus fault
Instrument cluster
disconnected
Instrument cluster
not configured
Instrument cluster
failure
Communications Network
U030055
Internal control
module
software
incompatibility,
not configured
Incorrect software
loaded
CAN wiring to
instrument cluster:
high resistance
Incorrect instrument
cluster CAN
configuration
Configure the air suspension control module and instrument
cluster as necessary using the approved diagnostic system.
U040186
Invalid data
received from
engine control
module (ECM)
Engine management
system (EMS) fault
Communications Network
U041686
Invalid data
received from
ABS module
ABS fault
Communications Network
Invalid data
received from
parking brake
module
Parking brake fault
Communications Network
U042886
Invalid data
received from
steering angle
sensor (SAS)
module
SAS module not
configured/calibrated
SAS fault
Check the security of the electrical connection.
Configure/calibrate the SAS using the approved diagnostic
system.
Communications Network
U043486
Invalid data
received from
active
stabilization
system
module
Active stabilization
system fault
Communications Network
U1A1387
Lost
communication
with terrain
optimization
switch
CAN bus fault
Terrain optimization
switch disconnected
Terrain response
module not
configured
Terrain response
module failure
Communications Network
U1A1449
CAN
initialization
failure
Internal electronic
failure
Communications Network
U1A3562
VIN from
instrument
cluster does
not match VIN
at time of
calibration
Air suspension
control module has
been swapped with
another vehicle
Instrument cluster
not configured
Configure the instrument cluster using the approved diagnostic
system.
U200067
Temperature
sensor voltage
takes too long
to read after
suitable
compressor
runtime
Compressor brush
card temperature
sensor harness
wiring: short circuit
to ground, short
circuit to power, high
resistance
Compressor brush
card temperature
sensor failure
Compressor fault
Refer to the guided diagnostic routine for this code on the
approved diagnostic system.
U200701
Valve circuit
short circuit to
ground
Water ingress to
wiring harness or
connectors
Valve harness
wiring: short circuit
to ground, high
resistance
Air suspension
control module
failure
C1A001D will be set first. Visually inspect the wiring harness and
connectors for water ingress. Refer to the guided diagnostic
routine for this code on the approved diagnostic system.
Valve circuit
short circuit to
Water ingress to
wiring harness or
connectors
Valve harness
wiring: short circuit
Visually inspect the wiring harness and connectors for water
system is
inactive
wiring: short circuit
to ground, high
resistance
Air suspension
control module
failure
ingress. Refer to the guided diagnostic routine for this code on
the approved diagnostic system.
U200719
Valve circuit
current above
threshold
Valve supply
circuit(s) intermittent:
short circuit to
ground, high
resistance
Valve failure
Air suspension
control module
failure
Refer to the guided diagnostic routine for this code on the
approved diagnostic system.
U200767
Valve signal
incorrect after
event
Water ingress to
wiring harness or
connectors (in
particular electrical
connector(s) C2527
and C2528)
Valve supply
circuit(s): short
circuit to ground,
short circuit to
power, high
resistance
Air suspension
control module
failure
Visually inspect the wiring harness and connectors for water
ingress. Refer to the guided diagnostic routine for this code on
the approved diagnostic system. Refer to the warranty policy and
procedures manual if a module is suspect.
Air suspension deflation exit routine
1 . Key on, engine off.
2 . Key off.
3 . Press and release raise switch.
4 . Press and release lower switch.
5 . Key on, engine off.
6 . Key on, engine running.
7 . Press and release raise switch twice.
8 . Press and release lower switch twice.
9 . Press and release raise switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст