Range Rover Sport. Manual — part 23
CAUTION: Make sure the bush is correctly aligned.
CAUTION: Make sure the correct special tool is used to install the bushings to the correct depth.
Using the special tools, install the lower arm rear bushings.
2 .
CAUTION: Make sure the bush is correctly aligned.
Using the special tools, install the lower arm front bushings
3 . Install the LH lower arm.
Fit the bolts but do not fully tighten at this stage.
4 . Connect the shock absorber and spring assembly to the lower arm.
Tighten the nut and bolt to 300 Nm (221 lb.ft).
5 . Release the halfshaft.
6 . Using the special tools, install the halfshaft in the wheel hub.
7 . Connect the upper arm and wheel knuckle.
Install a new nut and tighten to 70 Nm (52 lb.ft).
Vehicles without Active Stabilization
CAUTION: Make sure the hardened steel washer is installed between the stabilizer bar link and the
upper arm. Failure to follow this instruction may result in damage to the vehicle.
CAUTION: Use a Torx socket to prevent the ball joint rotating whilst installing the nut.
Secure the stabilizer bar link.
Tighten the nut to 175 Nm (129 lb.ft).
Vehicles with Active Stabilization
9
.
CAUTION: Make sure the hardened steel washer is installed between the stabilizer bar link and the
upper arm. Failure to follow this instruction may result in damage to the vehicle.
CAUTION: Use a Torx socket to prevent the ball joint rotating whilst installing the nut.
Secure the stabilizer bar link.
Install a new nut and tighten to 175 Nm (129 lb.ft).
All vehicles
10 . Connect the tie-rod end ball joint.
Install a new nut and tighten to 70 Nm (52 lb.ft).
11 . Install a new halfshaft retaining nut and lightly tighten.
12 . Secure the brake hose retaining bracket to the wheel knuckle.
Tighten the bolt to 25 Nm (18 lb.ft).
13 . Tighten the halfshaft retaining nut to 350 Nm (258 lb.ft).
Stake the nut to the halfshaft.
14
.
Set the height distance, between the center of the halfshaft end and the edge of the fender trim, to 462 mm
(18.19'').
15 . Tighten the lower arm bolts to 275 Nm (203 lb.ft).
Align the bolts to the marks made previously.
16 . Install the RH lower arm.
For additional information, refer to
Lower Arm (60.35.02)
17 . Install the wheels and tires.
Tighten the wheel nuts to 140 Nm (103 lb.ft).
Specifications
General Specifications
Item
Specification
Gap between underside of the toe link rubber boot and the integrated body frame bracket 15.0 mm (0.591 in)
Height between the center of the halfshaft end and the edge of the fender trim
463 mm (18.19 in)
Torque Specifications
Description
Nm lb-ft
** Toe link bolt
175 129
* Toe link inner ball joint retaining nut
133 98
* Stabilizer bar link nuts
115 85
Stabilizer bar clamp bolts
62
46
Body mount retaining bolts
133 83
Shock absorber to the lower suspension arm nut and bolt 300 221
Shock absorber to suspension turret nuts
63
46
Lower arm to wheel knuckle bolt
175 129
Lower arm bolts
275 203
*+ Halfshaft retaining nut
350 258
Upper arm to wheel knuckle nut
133 98
Upper arm front bolt
175 129
Upper arm rear bolt
275 203
Brake tube unions
18
13
Rear camber adjusting bolts
133 98
Wheel speed sensor
9
7
Brake disc dust shield bolts
9
7
Parking brake cable coupling
8
6
Road wheel nuts
140 103
* New nut must be installed + Nut must be staked after tightening ** Bolts may be reinstalled a maximum of 4 times, the bolt
head must be marked using a centre punch each time the bolt is refitted. When 4 centre punch marks are visible, a new,
'Patched' bolt must be installed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст