Jeep XJ. Manual — part 56
ASSEMBLY
(1) Install the CAB onto the HCU.
(2) Install the CAB mounting screws and tighten
to 1.8 N·m (16 in. lbs.).
(3) Install pump motor connector to the CAB.
SPECIFICATIONS
T0RQUE CHART
DESCRIPTION
TORQUE
G-Sensor
Sensor Bolt . . . . . . . . . . . . . . 3 N·m (27.5 in. lbs.)
Bracket Bolt . . . . . . . . . . . . . 2.7 N·m (24 in. lbs.)
Hydraulic Control Unit/Controller Antilock
Brakes
Mounting Nuts . . . . . . . . . 11.5 N·m (102 in. lbs.)
Brake Lines . . . . . . . . . . . . . 19 N·m (170 in. lbs.)
Controller Antilock Brakes
Mounting Screws . . . . . . . . . 1.8 N·m (16 in. lbs.)
Wheel Speed Sensors
Front Mounting Bolt . . . . . . 4.7 N·m (42 in. lbs.)
Rear Mounting Bolt . . . . . . . 13 N·m (115 in. lbs.)
5 - 40
BRAKES
XJ
DISASSEMBLY AND ASSEMBLY (Continued)
BRAKES
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
BRAKE BOOSTER – RHD DIESEL . . . . . . . . . . . . 1
MASTER CYLINDER – RHD DIESEL . . . . . . . . . . 3
SPECIFICATIONS
TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . 4
REMOVAL AND INSTALLATION
BRAKE BOOSTER – RHD DIESEL
REMOVAL
(1) Open hood and disconnect the negative battery
cable
NOTE: Pump the brake pedal several times to
relieve vacuum in the brake booster. This will pre-
vent booster from sucking any contaminants when
master cylinder is removed.
(2) Remove the short brake lines leading from the
master cylinder to the combination valve (Fig. 1).
(3) Disconnect differential pressure switch wire
from the combination valve. Lift the release tab on
the underside of the electrical connector and pull
straight off (Fig. 2).
(4) Remove the combination valve support bracket
retaining nuts and remove the valve and bracket
assembly from the vehicle.
(5) Remove the master cylinder retaining nuts
(Fig. 8) and remove the master cylinder from the
brake booster by sliding straight off mounting studs.
(6) Disconnect the vacuum supply hose from the
brake booster.
(7) Disconnect the coolant level switch electrical
connector. Located on the side of the coolant reser-
voir.
NOTE: It is not necessary to drain the cooling sys-
tem to perform this procedure.
(8) Remove the coolant reservoir retaining screws
so reservoir can be positioned out of the way.
(9) Working inside the vehicle, remove the hood
release cable handle retaining screws from the
underside of the instrument panel.
(10) Remove the plastic and steel knee blockers
from the vehicle. Refer to Group 23, Body for the pro-
cedure.
Fig. 1 Brake Line Orientation
1 – COMBINATION VALVE
2 – MASTER CYLINDER
Fig. 2 Differential Pressure Switch Electrical
1 – SWITCH TERMINAL
2 – COMBINATION VALVE
3 – WIRE HARNESS CONNECTOR
XJ
BRAKES
5 - 1
2000 JEEP CHEROKEE
(11) Remove the retaining clip that secures the
booster push rod to the brake pedal (Fig. 4).
(12) Remove nuts attaching booster to passenger
compartment side of dash panel (Fig. 5).
(13) Working inside the engine compartment, posi-
tion the coolant reservoir out of the way and remove
the brake booster by pulling straight out.
INSTALLATION
NOTE: Be certain rubber o-ring vacuum seal is
installed in the master cylinder mounting flange
prior to installation.
NOTE: If a new master cylinder is being installed,
cylinder must be bench bleed prior to installation.
(1) Install the brake booster on the bulkhead, be
certain dash seal is installed on booster studs prior
to installation.
(2) From under the instrument panel, install
booster mounting nuts. Tighten nuts just enough to
hold booster in place.
NOTE: Lubricate the pedal pin and bushing with
Mopar multi-mileage grease before installation.
(3) Slide booster push rod onto the brake pedal
pin. Then secure push rod to pedal pin with retaining
clip.
(4) Torque booster mounting nuts to 39 N·m (29 ft.
lbs.).
(5) Install the steel and plastic knee blocker in the
vehicle. Refer to Group 23, Body for the procedure.
(6) Install the hood release cable handle.
(7) Install the coolant reservoir bottle retaining
screws and connect the coolant level switch.
(8) Connect the vacuum supply hose on the brake
booster.
(9) Install master cylinder on brake booster and
install retaining nuts. Torque the nuts to 17.5 N·m
(155 in. lbs.).
(10) Install combination valve/bracket and retain-
ing nuts.
(11) Install brake lines on cylinder and valve.
Torque brake lines to 19 N·m (170 in. lbs.).
(12) Connect differential pressure switch wire on
the combination valve.
(13) Fill and bleed the brake system. Refer to the
procedure in this group.
(14) Connect the negative battery cable.
Fig. 3 Master Cylinder
1 – BOOSTER
2 – MASTER CYLINDER
Fig. 4 Booster Push Rod
1 – BRAKE PEDAL
2 – BOOSTER ROD
3 – BUSHING
Fig. 5 Booster Mounting
1 – BOOSTER
5 - 2
BRAKES
XJ
REMOVAL AND INSTALLATION (Continued)
2000 JEEP CHEROKEE
(15) Adjust the brake lamp switch. Refer to the
procedure in this group.
WARNING: Be
certain
a
firm
brake
pedal
is
achieved prior to attempting to operate the vehicle.
MASTER CYLINDER – RHD DIESEL
REMOVAL
(1) Open hood and disconnect the negative battery
cable
NOTE: Pump the brake pedal several times to
relieve vacuum in the brake booster. This will pre-
vent booster from sucking any contaminants when
master cylinder is removed.
(2) Remove the short brake lines leading from the
master cylinder to the combination valve (Fig. 6).
(3) Disconnect differential pressure switch wire
from the combination valve. Lift the release tab on
the underside of the electrical connector and pull
straight off (Fig. 7).
(4) Remove the combination valve support bracket
retaining nuts and remove the valve and bracket
assembly from the vehicle.
(5) Remove the master cylinder retaining nuts
(Fig. 8) and remove the master cylinder from the
brake booster by sliding straight off mounting studs.
INSTALLATION
NOTE: Be certain rubber o-ring vacuum seal is
installed in the master cylinder mounting flange
prior to installation.
NOTE: If a new master cylinder is being installed,
cylinder must be bench bleed prior to installation.
(1) If equipped, remove protective sleeve from pri-
mary piston shank on new master cylinder.
(2) Clean cylinder mounting surface of brake
booster.
(3) Install master cylinder on brake booster and
install retaining nuts. Torque the nuts to 17.5 N·m
(155 in. lbs.).
Fig. 6 Brake Line Orientation
1 – COMBINATION VALVE
2 – MASTER CYLINDER
Fig. 7 Differential Pressure Switch Electrical
1 – SWITCH TERMINAL
2 – COMBINATION VALVE
3 – WIRE HARNESS CONNECTOR
Fig. 8 Master Cylinder
1 – BOOSTER
2 – MASTER CYLINDER
XJ
BRAKES
5 - 3
REMOVAL AND INSTALLATION (Continued)
2000 JEEP CHEROKEE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст