Jeep XJ. Manual — part 122
LAMP BULB SERVICE
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
HEADLAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . 10
FOG LAMP BULB. . . . . . . . . . . . . . . . . . . . . . . . . 10
FRONT PARK/TURN SIGNAL LAMP BULB . . . . . . 11
SIDE MARKER LAMP BULB . . . . . . . . . . . . . . . . . 11
BACK-UP/BRAKE/REAR TURN SIGNAL/TAIL
LAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
LICENSE PLATE LAMP BULB . . . . . . . . . . . . . . . 12
CENTER HIGH MOUNTED STOP LAMP
(CHMSL) BULB . . . . . . . . . . . . . . . . . . . . . . . . . 12
UNDERHOOD LAMP BULB . . . . . . . . . . . . . . . . . 12
CARGO LAMP BULB . . . . . . . . . . . . . . . . . . . . . . 13
MAP READING LAMP BULB. . . . . . . . . . . . . . . . . 13
VISOR VANITY LAMP BULB. . . . . . . . . . . . . . . . . 13
REMOVAL AND INSTALLATION
HEADLAMP BULB
REMOVAL
(1) Remove the screws attaching the bezel to the
grille opening panel (Fig. 1).
(2) Remove screws attaching the retaining ring to
the headlamp canister.
(3) Disconnect the headlamp bulb wire harness
connector.
(4) Separate the sealed beam from the vehicle.
INSTALLATION
(1) Connect wire harness connector.
(2) Position bulb in canister.
(3) Position retaining ring on sealed beam and
install screws.
(4) Install headlamp bezel.
FOG LAMP BULB
REMOVAL
(1) Remove the screws attaching the access cover
to the bottom of the fog lamp (Fig. 2).
(2) Remove spring clip securing bulb to fog lamp.
(3) Disconnect bulb wire connector.
(4) Remove bulb element from fog lamp.
INSTALLATION
CAUTION: Do not touch the bulb glass with fingers
or other oily surfaces. Reduced bulb life will result.
(1) Position bulb element in fog lamp.
Fig. 1 Headlamp Bezel
1 – HEADLAMP ADJUSTMENT
2 – NUT
3 – HEADLAMP
4 – BEZEL
5 – PARK/TURN LAMP
6 – SPRING
7 – BUMPER
Fig. 2 Fog Lamp Components
1 – FOG LAMP
2 – CLIP
3 – BULB
4 – ACCESS COVER
5 – BULB SOCKET
8L - 10
LAMPS
XJ
(2) Connect bulb wire connector.
(3) Install spring clip securing bulb to fog lamp.
(4) Install screws attaching the access cover to the
bottom of the fog lamp.
FRONT PARK/TURN SIGNAL LAMP BULB
REMOVAL
(1) Remove headlamp bezel.
(2) Remove
screws
attaching
park/turn
signal
lamp housing to grille opening panel.
(3) Rotate bulb socket one-third turn counter-clock-
wise and remove it from lamp housing (Fig. 3).
(4) Pull bulb from socket.
INSTALLATION
(1) Install bulb in socket.
(2) Install socket in lamp housing.
(3) Install park/turn signal lamp housing.
(4) Install headlamp bezel.
SIDE MARKER LAMP BULB
REMOVAL
(1) Remove screws attaching side marker lamp
housing.
(2) Rotate bulb socket counter-clockwise and pull
from back side of lamp housing (Fig. 4).
(3) Pull bulb from socket.
INSTALLATION
(1) Install bulb in socket.
(2) Install bulb and socket in back of side marker
lamp housing.
(3) Install side marker lamp housing.
BACK-UP/BRAKE/REAR TURN SIGNAL/TAIL
LAMP BULB
REMOVAL
(1) Remove tail lamp housing.
(2) Rotate bulb socket one-third turn counter-clock-
wise and remove bulb socket from lamp housing (Fig.
5).
(3) Pull bulb from socket.
INSTALLATION
(1) Install bulb in socket.
(2) Install bulb and socket in lamp housing.
(3) Install lamp housing.
Fig. 3 Park/Turn Signal Lamp Bulb
1 – BULB SOCKET
2 – PARK LAMP HOUSING
3 – PARK LAMP BULB
Fig. 4 Side Marker Lamp
1 – SIDE MARKER LAMP HOUSING
2 – SIDE MARKER LAMP BULB
3 – BULB SOCKET
Fig. 5 Bulb Socket Removal
1 – TAIL LAMP BULB
2 – BULB SOCKET
3 – TAIL LAMP HOUSING
XJ
LAMPS
8L - 11
REMOVAL AND INSTALLATION (Continued)
LICENSE PLATE LAMP BULB
REMOVAL
(1) Remove screws attaching license plate lamp
housing to liftgate.
(2) Rotate
bulb
socket
counter-clockwise
and
remove bulb socket from lamp housing.
(3) Pull bulb from socket.
INSTALLATION
(1) Install bulb in lamp socket.
(2) Install bulb socket in lamp housing.
(3) Install screws attaching license plate lamp
housing to liftgate.
CENTER HIGH MOUNTED STOP LAMP
(CHMSL) BULB
REMOVAL
(1) Remove the screws attaching the lamp housing
to the liftgate.
(2) Rotate bulb socket 1/4 turn counter-clockwise
and pull from housing (Fig. 6).
(3) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Position socket in lamp and rotate 1/4 turn
clockwise.
(3) Install screws attaching lamp housing to the
liftgate.
UNDERHOOD LAMP BULB
REMOVAL
(1) Insert a small flat blade in the access slot
between the lamp base and lamp lens.
(2) Pry the lamp lens upward and remove the
lamp lens (Fig. 7).
(3) Depress the bulb terminal inward (Fig. 8) to
release the bulb.
INSTALLATION
(1) Engage the replacement bulb wire loop to the
terminal closest to the lamp base wire connector.
Fig. 6 CHMSL Bulb
1 – CHMSL BULB
2 – BULB SOCKET
3 – CHMSL LAMP HOUSING
Fig. 7 Underhood Lamp Lens
1 – LAMP
2 – LAMP LENS
Fig. 8 Underhood Lamp Bulb
1 – BULB
2 – DEPRESS TERMINAL INWARD
3 – BULB WIRE LOOP
4 – LAMP BASE
8L - 12
LAMPS
XJ
REMOVAL AND INSTALLATION (Continued)
(2) Depress the opposite terminal inward and
engage the remaining bulb wire loop.
(3) Position the lamp lens on the lamp base and
press into place.
CARGO LAMP BULB
REMOVAL
(1) Insert a small flat blade into the access slots
(Fig. 9).
(2) Carefully pry the lens from the lamp.
(3) Grasp bulb and pull from lamp.
INSTALLATION
(1) Position bulb in lamp and snap into place.
(2) Position the lens at the lamp housing and force
it upward into the housing until the mounting tabs
are seated on the lamp mounting pins.
MAP READING LAMP BULB
REMOVAL
(1) Insert a flat blade screwdriver in slot at front
of lens (Fig. 10).
(2) Rotate the screwdriver until lens snaps out of
the housing.
(3) Remove lens from housing.
(4) Remove bulb from terminals.
INSTALLATION
(1) Insert bulb into reading lamp terminals.
(2) Replace lens by holding lens level and pushing
rearward into housing.
(3) Push lens up to snap into housing.
VISOR VANITY LAMP BULB
REMOVAL
(1) Using a small flat blade, carefully pry each cor-
ner of lens outward from lamp.
(2) Separate lens from lamp.
(3) Grasp bulb and pull outward.
INSTALLATION
(1) Position bulb in socket and push into place.
(2) Position lens on lamp and snap into place.
Fig. 9 Cargo Lamp Lens
1 – HOUSING
2 – SCREWDRIVER SLOTS
3 – CARGO LAMP
4 – LENS
Fig. 10 Reading Lamp Bulb
1 – LENS
2 – FLAT BLADE
3 – CONSOLE
XJ
LAMPS
8L - 13
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст