Jeep XJ. Manual — part 63
SPECIFICATIONS
SPECIFICATIONS
DESCRIPTION
TORQUE
Clutch Cover to Flywheel
Bolts . . . . . . . . . . . . . . . . . . . 50 N·m (37 ft. lbs.)
Clutch Housing to Transmission
Bolts . . . . . . . . . . . . . . . . . . . 46 N·m (34 ft. lbs.)
Flywheel to Crankshaft
Bolts . . . . . See removal and installation procedure.
Pilot Bearing Retainer to Flywheel/Crankshaft
Bolts . . . . . . . . . . . . . . . . . . . 28 N·m (20 ft. lbs.)
Clutch Housing to Engine
Top (2) Bolts . . . . . . . . . . . . . . 37 N·m (27 ft. lbs.)
Middle (2) Bolts . . . . . . . . . . . 58 N·m (43 ft. lbs.)
Bottom (2) Bolts . . . . . . . . . . . 75 N·m (55 ft. lbs.)
SPECIAL TOOLS
SPECIAL TOOLS
Fig. 18 Clutch Cover (Pressure Plate) View
1 – VEHICLE UNDERBODY
2 – ENGINE SPEED SENSOR
3 – PRESSURE PLATE RETAINING BOLTS
4 – CLUTCH COVER (PRESSURE PLATE)
5 – ENGINE OIL PAN
6 – PRESSURE PLATE RETAINING BOLTS
Universal Handle—C-4171
6 - 8
CLUTCH
XJ
REMOVAL AND INSTALLATION (Continued)
2000 JEEP CHEROKEE
COOLING SYSTEM
TABLE OF CONTENTS
page
page
DESCRIPTION AND OPERATION
COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . 1
AUTOMATIC TRANSMISSION OIL COOLER. . . . . 2
COOLANT RESERVE/OVERFLOW SYSTEM . . . . . 2
COOLING SYSTEM FANS . . . . . . . . . . . . . . . . . . . 3
BLOCK HEATER . . . . . . . . . . . . . . . . . . . . . . . . . . 4
THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
RADIATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
RADIATOR PRESSURE CAP . . . . . . . . . . . . . . . . . 5
WATER PUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
HOSE CLAMPS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VISCOUS FAN DRIVE . . . . . . . . . . . . . . . . . . . . . . 7
ELECTRIC COOLING FAN . . . . . . . . . . . . . . . . . . . 8
DIAGNOSIS AND TESTING
ON-BOARD DIAGNOSTICS (OBD) . . . . . . . . . . . . 9
DRB SCAN TOOL . . . . . . . . . . . . . . . . . . . . . . . . . 9
ACCESSORY DRIVE BELT DIAGNOSIS. . . . . . . . . 9
PRELIMINARY CHECKS . . . . . . . . . . . . . . . . . . . 11
RADIATOR COOLANT FLOW CHECK . . . . . . . . . 17
COOLING SYSTEM—TESTING FOR LEAKS . . . . 17
VISCOUS FAN DRIVE . . . . . . . . . . . . . . . . . . . . . 19
ELECTRIC COOLING FAN . . . . . . . . . . . . . . . . . . 19
RADIATOR CAP-TO-FILLER NECK
SEAL—PRESSURE RELIEF CHECK . . . . . . . . . 20
RADIATOR CAP—PRESSURE TESTING. . . . . . . 20
COOLANT—LOW LEVEL AERATION . . . . . . . . . 21
DEAERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SERVICE PROCEDURES
COOLANT—ROUTINE LEVEL CHECK. . . . . . . . . 21
COOLANT—ADDING ADDITIONAL. . . . . . . . . . . 21
COOLANT—LEVEL CHECK . . . . . . . . . . . . . . . . . 21
COOLING SYSTEM—DRAINING AND
FILLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
COOLING SYSTEM—REVERSE FLUSHING . . . . 22
REMOVAL AND INSTALLATION
TRANSMISSION OIL COOLERS . . . . . . . . . . . . . 23
COOLANT RESERVE TANK . . . . . . . . . . . . . . . . . 23
WATER PUMP . . . . . . . . . . . . . . . . . . . . . . . . . . 24
THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
RADIATOR—2.5L . . . . . . . . . . . . . . . . . . . . . . . . 29
RADIATOR—4.0L . . . . . . . . . . . . . . . . . . . . . . . . 31
ELECTRIC COOLING FAN—2.5L . . . . . . . . . . . . 33
ELECTRIC COOLING FAN—4.0L . . . . . . . . . . . . 34
BLOCK HEATER . . . . . . . . . . . . . . . . . . . . . . . . . 35
ENGINE ACCESSORY DRIVE BELTS. . . . . . . . . . 35
COOLING SYSTEM FANS . . . . . . . . . . . . . . . . . . 38
VISCOUS FAN DRIVE REMOVAL/
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . 39
CLEANING AND INSPECTION
RADIATOR PRESSURE CAP . . . . . . . . . . . . . . . . 39
RADIATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
WATER PUMP . . . . . . . . . . . . . . . . . . . . . . . . . . 39
FAN BLADE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
COOLING SYSTEM HOSES. . . . . . . . . . . . . . . . . 40
SPECIFICATIONS
SPECIAL TOOLS
COOLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DESCRIPTION AND OPERATION
COOLING SYSTEM
DESCRIPTION
The cooling system regulates engine operating tem-
perature. It allows the engine to reach normal oper-
ating temperature as quickly as possible, maintains
normal operating temperature and prevents over-
heating.
The cooling system also provides a means of heat-
ing the passenger compartment and cooling the auto-
matic transmission fluid (if equipped). The cooling
system is pressurized and uses a centrifugal water
pump to circulate coolant throughout the system.
An optional factory installed heavy duty cooling
package is available on most models. The package
consists of a radiator that has an increased number
of cooling fins. Vehicles equipped with a 2.5L/4.0L
engine and heavy duty cooling and/or air condition-
ing also have an auxiliary electric cooling fan.
The cooling system consists of:
• A radiator
• Cooling fan (mechanical and/or electrical)
• Thermal viscous fan drive
XJ
COOLING SYSTEM
7 - 1
• Fan shroud
• Radiator pressure cap
• Thermostat
• Coolant reserve/overflow system
• Transmission oil cooler (if equipped with an
automatic transmission)
• Coolant
• Water pump
• Hoses and hose clamps
Cooling system circulation for 2.5L/4.0L models is
shown in (Fig. 1).
AUTOMATIC TRANSMISSION OIL COOLER
DESCRIPTION
All models equipped with an automatic transmis-
sion are equipped with a transmission oil cooler
mounted internally within the radiator tank. This
internal cooler is supplied as standard equipment on
all models equipped with an automatic transmission.
Transmission oil is cooled when it passes through
this separate cooler. In case of a leak in the internal
radiator mounted transmission oil cooler, engine cool-
ant may become mixed with transmission fluid or
transmission fluid may enter engine cooling system.
Both cooling system and transmission should be
drained
and
inspected
if
the
internal
radiator
mounted transmission cooler is leaking.
An auxiliary air-to-oil transmission oil cooler is
available with most engine packages.
The auxiliary air-to-oil transmission oil cooler is
located in front of the radiator or A/C condenser (if
equipped) and behind the grill. It is mounted to the
front frame crossmember.
The auxiliary oil coolers on all models operate in
conjunction with the internal radiator mounted main
oil cooler. The transmission oil is routed through the
main cooler first, then the auxiliary cooler, before
returning to the transmission.
COOLANT RESERVE/OVERFLOW SYSTEM
DESCRIPTION
The system works along with the radiator pressure
cap. This is done by using thermal expansion and
contraction of the coolant to keep the coolant free of
trapped air. It provides:
• A volume for coolant expansion and contraction.
• A convenient and safe method for checking/ad-
justing coolant level at atmospheric pressure. This is
done without removing the radiator pressure cap.
• Some reserve coolant to the radiator to cover
minor leaks and evaporation or boiling losses.
Fig. 1 Coolant Circulation—2.5L/4.0L Engines
1 – HEATER CORE
2 – TO COOLANT RESERVE/OVERFLOW TANK
3 – THERMOSTAT HOUSING
4 – RADIATOR
5 – WATER PUMP
Fig. 2 Auxiliary Transmission Oil Cooler
1 – AUXILIARY TRANSMISSION OIL COOLER
7 - 2
COOLING SYSTEM
XJ
DESCRIPTION AND OPERATION (Continued)
The coolant reserve/overflow system consists of a
radiator mounted pressurized cap, a plastic reserve/
overflow tank (Fig. 3) (Fig. 4), a tube (hose) connect-
ing the radiator and tank, and an overflow tube on
the side of the tank.
OPERATION
As the engine cools, a vacuum is formed in the
cooling system of both the radiator and engine. Cool-
ant will then be drawn from the coolant tank and
returned to a proper level in the radiator.
COOLING SYSTEM FANS
DESCRIPTION
All models are equipped with a viscous fan. This
thermal viscous fan drive is a torque-and-tempera-
ture-sensitive clutch unit. It automatically increases
or decreases fan speed to provide proper engine cool-
ing. Vehicles with a 2.5L/4.0L engine with air condi-
tioning, or 4.0L with “max” cooling also have an
auxiliary electrical cooling fan.
Fig. 3 Reserve/Overflow Tank—Except Right Hand
Drive
1 – COOLANT RESERVE/OVERFLOW TANK
2 – CLAMP
3 – MOUNTING BOLTS
4 – TUBE TO RADIATOR
Fig. 4 Reserve/Overflow Tank—With Right Hand
Drive
1 – CLAMP
2 – COOLANT RESERVE/OVERFLOW TANK
3 – MOUNTING BOLTS
4 – LOWER BRACKET
5 – TUBE TO RADIATOR
Fig. 5 Viscous Fan Drive and Fan Blade Assembly
1 – VISCOUS FAN DRIVE
2 – FAN BLADE ASSEMBLY
XJ
COOLING SYSTEM
7 - 3
DESCRIPTION AND OPERATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст