Jeep XJ. Manual — part 6
CAUTION: Do not crank starter motor on disabled
vehicle for more than 15 seconds, starter will over-
heat and could fail.
(6) Allow battery in disabled vehicle to charge to
at least 12.4 volts (75% charge) before attempting to
start engine. If engine does not start within 15 sec-
onds, stop cranking engine and allow starter to cool
(15 min.), before cranking again.
DISCONNECT CABLE CLAMPS AS FOLLOWS:
• Disconnect BLACK cable clamp from engine
ground on disabled vehicle.
• When using a Booster vehicle, disconnect
BLACK cable clamp from battery negative terminal.
Disconnect RED cable clamp from battery positive
terminal.
• Disconnect RED cable clamp from battery posi-
tive terminal on disabled vehicle.
TWO-WHEEL-DRIVE VEHICLE TOWING
TOWING-REAR END LIFTED (SLING-TYPE)
WARNING: WHEN TOWING A DISABLED VEHICLE
AND THE DRIVE WHEELS ARE SECURED IN A
WHEEL LIFT OR TOW DOLLIES, ENSURE THE
TRANSMISSION IS IN THE PARK POSITION (AUTO-
MATIC TRANSMISSION) OR A FORWARD DRIVE
GEAR (MANUAL TRANSMISSION).
CAUTION: Do not use steering column lock to
secure steering wheel during towing operation.
2WD XJ vehicles can be towed with the front
wheels on the surface for extended distances at
speeds not exceeding 48 km/h (30 mph). If the vehicle
is equipped with a factory installed trailer tow pack-
age, use a SAE approved wheel lift device.
(1) Attach J-hooks around the axle shaft tube out-
board of the shock absorber.
(2) Place the sling crossbar under and forward of
the bumper.
(3) Attach safety chains around the frame rails.
(4) Turn the ignition switch to the OFF position to
unlock the steering wheel.
(5) Secure steering wheel in the straight ahead
position with a clamp device designed for towing.
(6) Verify that steering components are in good
condition.
(7) Shift the transmission to NEUTRAL.
TOWING-REAR END LIFTED (WHEEL LIFT)
(1) Raise front of vehicle off ground and install tow
dollies under front wheels.
(2) Attach wheel lift to rear wheels.
(3) Place transmission in neutral.
(4) Raise vehicle to towing height.
(5) Place transmission in park (automatic trans-
mission) or fist gear (manual transmission).
TOWING-FRONT END LIFTED
To prevent damage to front fascia components, use
only a Wheel-Lift type towing device or Flat-Bed
hauling equipment.
If using the wheel-lift towing method:
(1) Raise rear of vehicle off ground and install tow
dollies under rear wheels.
(2) Attach wheel lift to front wheels.
(3) Place transmission in neutral.
(4) Raise vehicle to towing height.
(5) Place transmission in park (automatic trans-
mission) or fist gear (manual transmission).
FOUR-WHEEL-DRIVE VEHICLE TOWING
DaimlerChrysler Corporation recommends that a
4WD vehicle be transported on a flat bed device. A
wheel lift or sling type device can be used provided
all wheels are lifted off the ground using tow dollies.
If the vehicle is equipped with a factory installed
trailer tow package, use a SAE approved wheel lift
device.
WARNING: WHEN TOWING A DISABLED VEHICLE
AND THE DRIVE WHEELS ARE SECURED IN A
WHEEL LIFT OR TOW DOLLIES, ENSURE THE
TRANSMISSION IS IN THE PARK POSITION (AUTO-
MATIC TRANSMISSION) OR A FORWARD DRIVE
GEAR (MANUAL TRANSMISSION).
TOWING-REAR END LIFTED (SLING TYPE)
(1) Raise front of vehicle off ground and install tow
dollies under front wheels.
(2) Attach J-hooks around rear axle shaft tube out-
board of shock absorber.
(3) Place sling crossbar under and forward of
bumper.
(4) Attach safety chains around frame rails.
(5) Turn ignition switch to OFF position to unlock
steering wheel.
(6) Secure steering wheel in the straight ahead
position with a clamp device designed for towing.
(7) Shift transfer case to neutral.
0 - 10
LUBRICATION AND MAINTENANCE
XJ
SERVICE PROCEDURES (Continued)
TOWING-REAR END LIFTED (WHEEL LIFT)
(1) Raise front of vehicle off ground and install tow
dollies under front wheels.
(2) Attach wheel lift to rear wheels.
(3) Place transmission in neutral.
(4) Raise vehicle to towing height.
(5) Place transmission in park (automatic trans-
mission) or first gear (manual transmission).
TOWING-FRONT END LIFTED
To prevent damage to front fascia components, use
only a Wheel-Lift type towing device or Flat-Bed
hauling equipment.
(1) Raise the rear of the vehicle off the ground and
install tow dollies under rear wheels.
(2) Attach wheel lift to front wheels.
(3) Place transmission in neutral.
(4) Raise vehicle to towing height.
(5) Place transmission in park (automatic trans-
mission) or first gear (manual transmission).
EMERGENCY TOW HOOKS
WARNING: REMAIN AT A SAFE DISTANCE FROM A
VEHICLE THAT IS BEING TOWED VIA ITS TOW
HOOKS. THE TOW STRAPS/CHAINS COULD BREAK
AND CAUSE SERIOUS INJURY.
Some Jeep vehicles are equipped with front and
rear emergency tow hooks. The tow hooks should be
used for EMERGENCY purposes only.
CAUTION: DO NOT use emergency tow hooks for
tow truck hook-up or highway towing.
HOISTING RECOMMENDATIONS
Refer to the Owner’s Manual for emergency vehicle
lifting procedures.
FLOOR JACK
When properly positioned, a floor jack can be used
to lift a Jeep vehicle (Fig. 2) and (Fig. 3). Support the
vehicle in the raised position with jack stands at the
front and rear ends of the frame rails.
Fig. 2 Vehicle Lifting Locations
XJ
LUBRICATION AND MAINTENANCE
0 - 11
SERVICE PROCEDURES (Continued)
CAUTION: Do not attempt to lift a Jeep vehicle with
a floor jack positioned under:
• An axle tube.
• A body side sill.
• A steering linkage component.
• A drive shaft.
• The engine or transmission oil pan.
• The fuel tank.
• A front suspension arm.
NOTE: Use the correct sub-frame rail or frame rail
lifting locations only.
HOIST
A vehicle can be lifted with:
• A single-post, frame-contact hoist.
• A twin-post, chassis hoist.
• A ramp-type, drive-on hoist.
NOTE: When a frame-contact type hoist is used,
verify that the lifting pads are positioned properly.
WARNING: THE
HOISTING
AND
JACK
LIFTING
POINTS PROVIDED ARE FOR A COMPLETE VEHI-
CLE. WHEN A CHASSIS OR DRIVETRAIN COMPO-
NENT
IS
REMOVED
FROM
A
VEHICLE,
THE
CENTER OF GRAVITY IS ALTERED MAKING SOME
HOISTING
CONDITIONS
UNSTABLE.
PROPERLY
SUPPORT OR SECURE VEHICLE TO HOISTING
DEVICE WHEN THESE CONDITIONS EXIST.
Fig. 3 Correct Vehicle Lifting Locations
1 – SUB-FRAME RAIL LOCATION
2 – SUB-FRAME RAIL LOCATION
0 - 12
LUBRICATION AND MAINTENANCE
XJ
SERVICE PROCEDURES (Continued)
LUBRICATION AND MAINTENANCE
TABLE OF CONTENTS
page
page
LUBRICANTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MAINTENANCE SCHEDULE. . . . . . . . . . . . . . . . . . . 2
LUBRICANTS
TABLE OF CONTENTS
page
page
SPECIFICATIONS
ENGINE OIL—DIESEL ENGINES . . . . . . . . . . . . . . 1
FLUID CAPACITIES . . . . . . . . . . . . . . . . . . . . . . . . 1
SPECIFICATIONS
ENGINE OIL—DIESEL ENGINES
Use only Diesel Engine Oil meeting standard MIL-
2104C or API Classification CD or higher or CCML
D4, D5.
SAE VISCOSITY GRADE
CAUTION: Low viscosity oils must have the proper
API quality or the CCMC G5 designation.
To assure of properly formulated engine oils, it is
recommended that SAE Grade 15W-40 engine oils
that meet Chrysler material standard MS-6395, be
used. European Grade 10W-40 oils are also accept-
able.
Oils of the SAE 5W-40 or 8W-80 grade number are
preferred when minimum temperatures consistently
fall below -12°C.
FLUID CAPACITIES
FUEL TANK
Diesel Engine Equipped Vehicles . . . . . . . . . 76.4 L
ENGINE OIL
2.5L Diesel Engine (includes filter) . . . . . . . . . 6.8 L
Oil Filter Replacement Only . . . . . . . . . . . . . . 0.4 L
COOLING SYSTEM
2.5L Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0 L
MANUAL TRANSMISSION
Recommended lubricant for AX15 transmissions is
Mopar
t 75W–90, API Grade GL–3 gear lubricant, or
equivalent.
Correct lubricant level is from the bottom edge, to
no more than 6 mm (1/4 in.) below the bottom edge of
the fill plug hole.
Approximate dry fill lubricant capacity is:
• 3.10 liters (3.27 qts.) for 4–wheel drive applica-
tions.
• 3.15 liters (3.32 qts.) for 2–wheel drive applica-
tions.
TRANSFER CASE
COMMAND-TRAC 231 . . . . . . . . . . . . . . . . . . 1.3 L
FRONT AXLE
Model 181 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 L
REAR AXLE
Model 194 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 L*
8-1/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 L**
* When equipped with TRAC-LOK, include 4
ounces of Friction Modifier Additive.
** When equipped with TRAC-LOK, include 5
ounces of Friction Modifier Additive.
XJ
LUBRICATION AND MAINTENANCE
0 - 1
2000 JEEP CHEROKEE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст