Jeep XJ. Manual — part 126
LAMP BULB SERVICE
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
FRONT POSITION LAMP BULB
REMOVAL
(1) Remove the 2 screws holding the headlamp
bezel in place and remove bezel (Fig. 1).
(2) Remove the 4 screws holding the headlamp
(Fig. 2).
(3) Pull the front position lamp straight from
headlamp (Fig. 3).
(4) Remove the front position lamp bulb from
socket.
INSTALLATION
(1) Install the front position lamp bulb in lamp
socket.
(2) Verify lamp operation.
(3) Install front position lamp in headlamp.
(4) Connect headlamp electrical connector.
(5) Position the headlamp, headlamp retaining
ring and install the retaining screws.
(6) Position the headlamp bezel and install retain-
ing screws.
SIDE REPEATER LAMP BULB
REMOVAL
(1) Grip the side repeater lamp assembly and pull
straight from the fender.
(2) Rotate and pull the socket from the housing
(Fig. 4).
(3) Pull the bulb straight from the socket.
Fig. 1 Headlight Bezel Retaining Screws
Fig. 2 Headlamp Retaining Screws
Fig. 3 Front Position Lamp Grommet & Socket
Location
1 – GROMMET
2 – SOCKET
8L - 6
LAMPS
XJ
2000 JEEP CHEROKEE
INSTALLATION
(1) Align the side repeater lamp bulb to the socket
(Fig. 4).
(2) Push the bulb into the socket.
(3) Verify lamp operation.
(4) Push and rotate the socket into the housing.
(5) Press the lamp assembly into the fender
mounting hole.
REAR FOG LAMP BULB
REMOVAL
(1) There are 3 mounting bolts attaching the tail-
light assembly. When removing, unfasten the 3 bolts
located on the top and side. Lift up and out to
remove the assembly.
(2) Turn the socket assembly 1/3 turn and pull the
socket from the housing (Fig. 5).
(3) Pull the rear fog lamp straight from its socket.
INSTALLATION
(1) Install rear fog lamp bulb in its socket.
(2) Verify lamp operation.
(3) Install the remaining three lamp sockets in the
taillamp assembly.
(4) Position the taillamp assembly and install the
retaining screws.
LICENSE PLATE LAMP BULB
REMOVAL
(1) Remove the appropriate license plate lamp
retaining screws.
(2) Pull lamp housing from rear liftgate. Lamp
must be positioned properly to allow removal without
removing license plate.
(3) Rotate the lamp socket counter clockwise and
pull straight from lamp housing.
(4) Pull the lamp bulb straight from its socket.
INSTALLATION
(1) Install bulb in lamp socket.
(2) Verify lamp operation.
(3) Install lamp socket in lamp housing.
(4) Install license plate lamp assembly in liftgate
and install retaining screws.
Fig. 4 Side Repeater Lamp
Fig. 5 Rear Lamp Replacement
XJ
LAMPS
8L - 7
REMOVAL AND INSTALLATION (Continued)
2000 JEEP CHEROKEE
LAMP SERVICE
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
HEADLAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
HEADLAMP LEVELING MOTOR. . . . . . . . . . . . . . . 8
SIDE REPEATER LAMP . . . . . . . . . . . . . . . . . . . . . 9
FRONT FOG LAMP . . . . . . . . . . . . . . . . . . . . . . . . 9
REAR TURN SIGNAL, BACKUP, TAILLAMP
AND FOG LAMP . . . . . . . . . . . . . . . . . . . . . . . . . 9
LICENSE PLATE LAMP . . . . . . . . . . . . . . . . . . . . . 9
REMOVAL AND INSTALLATION
HEADLAMP
REMOVAL
(1) Remove the 2 screws holding the headlamp
bezel in place and remove bezel (Fig. 1).
(2) Remove the 4 screws holding the headlamp
(Fig. 2).
(3) Pull the front position lamp straight from
headlamp.
(4) Disconnect the headlamp electrical connector
by pulling straight off.
(5) Remove the headlamp from the vehicle.
INSTALLATION
(1) Install front position lamp in headlamp.
(2) Connect headlamp electrical connector.
(3) Position the headlamp, headlamp retaining
ring and install the retaining screws.
(4) Position the headlamp bezel and install retain-
ing screws.
HEADLAMP LEVELING MOTOR
REMOVAL
(1) Open the hood and disconnect the negative bat-
tery cable.
(2) Raise the vehicle on a hoist or position a
creeper under the front of the vehicle.
(3) Remove
the
appropriate
side
front
splash
shield. Located just in front of the front wheel.
Fig. 1 Headlight Bezel Retaining Screws
Fig. 2 Headlamp Retaining Screws
Fig. 3 Headlamp Leveling Motor
1 – HEADLAMP LEVELING MOTOR
2 – FRONT STABILIZER BAR
8L - 8
LAMPS
XJ
2000 JEEP CHEROKEE
(4) Disconnect the headlamp leveling motor electri-
cal connector.
(5) Rotate the leveling motor 90 degrees until
motor is loose in mounting bracket.
(6) Tilt motor upwards to disconnect motor push
rod from the headlamp leveling linkage.
(7) Remove the headlamp leveling motor from the
vehicle (Fig. 3).
INSTALLATION
(1) Install leveling motor push rod through hole in
mounting bracket and connect push rod on leveling
linkage. The proper angle must be achieved to con-
nect the push rod onto the leveling linkage.
(2) Once the push rod is connected, rotate motor
until tabs line up with tabs in mounting bracket.
Once the tabs are lined up push and rotate the motor
90 degrees to lock in place.
(3) Connect the headlamp leveling motor electrical
connector.
(4) Position the front splash shield.
(5) Lower the vehicle and connect the negative
battery cable.
SIDE REPEATER LAMP
REMOVAL
(1) Grip the side repeater lamp assembly and pull
straight from the fender.
(2) Rotate and pull the socket from the housing
(Fig. 4).
INSTALLATION
(1) Push and rotate the socket into the housing.
(2) Verify lamp operation.
(3) Press the lamp assembly into the fender
mounting hole.
FRONT FOG LAMP
REMOVAL
1. Remove the 2 screws from the bottom cover of
the lamp body.
2. Disconnect the 2 wires from the lamp element.
3. Remove the lamp element from the housing.
INSTALLATION
1. Install the new lamp element in the housing
and reinstall the lower housing.
REAR TURN SIGNAL, BACKUP, TAILLAMP AND
FOG LAMP
REMOVAL
(1) There are 3 mounting bolts attaching the tail-
light assembly. When removing, unfasten the 3 bolts
located on the top and side. Lift up and out to
remove the assembly.
(2) Turn the socket assembly 1/3 turn and pull the
socket from the housing (Fig. 5).
INSTALLATION
(1) Install the four lamp sockets in the taillamp
assembly.
(2) Verify lamp operation.
(3) Position the taillamp assembly and install the
retaining screws.
LICENSE PLATE LAMP
REMOVAL
(1) Remove the appropriate license plate lamp
retaining screws.
(2) Pull lamp housing from rear liftgate. Lamp
must be positioned properly to allow removal without
removing license plate.
(3) Rotate the lamp socket counter clockwise and
pull straight from lamp housing.
Fig. 4 Side Repeater Lamp
Fig. 5 Rear Lamp Replacement
XJ
LAMPS
8L - 9
REMOVAL AND INSTALLATION (Continued)
2000 JEEP CHEROKEE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст