Jeep XJ. Manual — part 469
SPECIFICATIONS
TORQUE
DESCRIPTION
TORQUE
Clutch Housing to Engine Top (2) Bolts . . 36.6 N·m
(27 ft. lbs.)
Clutch Housing to Engine Mid-Point
(2) Bolts . . . . . . . . . . . . . . . 58.3 N·m (43 ft. lbs.)
Clutch Housing to Engine Bottom
(2) Bolts . . . . . . . . . . . . . . . 74.6 N·m (55 ft. lbs.)
Clutch Housing to Transmission bolts . . . 38.0 N·m
(28 ft. lbs.)
Transfer Case to Transmission
Attaching Nuts . . . . . . . . . . . 35 N·m (26 ft. lbs.)
Propeller Shaft Bolts . . . . . . 26.5 N·m (19.5 ft. lbs.)
Fig. 6 Clutch Housing to Transmission
1 – TRANSMISSION
2 – CLUTCH HOUSING
3 – CLUTCH HOUSING BOLT
4 – RELEASE BEARING
5 – RELEASE FORK
6 – PIVOT
Fig. 7 Fill Plug Location
1 – GEAR CASE
2 – FILL PLUG
21 - 4
TRANSMISSION AND TRANSFER CASE
XJ
SPECIFICATIONS (Continued)
2000 JEEP CHEROKEE
NV231 TRANSFER CASE
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
TRANSFER CASE . . . . . . . . . . . . . . . . . . . . . . . . . 5
SPECIFICATIONS
TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
REMOVAL AND INSTALLATION
TRANSFER CASE
REMOVAL
(1) Shift transfer case into Neutral.
(2) Raise vehicle.
(3) Drain transfer case lubricant.
(4) Mark front and rear propeller shaft yokes for
alignment reference.
(5) Support transmission with jack stand.
(6) Remove rear crossmember and skid plate, if
equipped.
(7) Disconnect and support front/rear propeller
shafts at transfer case.
(8) Disconnect vehicle speed sensor wires.
(9) Disconnect transfer case linkage rod from
range lever.
(10) Disconnect transfer case vent hose (Fig. 1)
and indicator switch harness, if necessary.
(11) Support transfer case with transmission jack.
(12) Secure transfer case to jack with chains.
(13) Remove nuts attaching transfer case to trans-
mission.
(14) Pull transfer case and jack rearward to disen-
gage transfer case.
(15) Remove transfer case from under vehicle.
INSTALLATION
(1) Mount transfer case on a transmission jack.
(2) Secure transfer case to jack with chains.
(3) Position transfer case under vehicle.
(4) Align transfer case and transmission shafts
and install transfer case on transmission.
(5) Install and tighten transfer case attaching nuts
to 35 N·m (Fig. 1).
(6) Connect vehicle speed sensor wires, and vent
hose.
(7) Connect indicator switch harness to transfer
case switch, if necessary. Secure wire harness to clips
on transfer case.
NOTE: Do no reuse bearing straps or bolts. Discard
and replace with new.
(8) Align and connect propeller shafts. Tighten
shaft attaching bolts to 26.5 N·m torque.
(9) Fill transfer case with correct fluid. Refer to
Recommended Lubricant And Fill Level section for
proper fluid and capacity.
(10) Install rear crossmember and skid plate, if
equipped. Tighten crossmember bolts.
(11) Remove transmission jack and support stand.
(12) Connect shift rod to transfer case range lever.
(13) Adjust transfer case shift linkage.
(14) Lower vehicle and verify transfer case shift
operation.
SPECIFICATIONS
TORQUE
DESCRIPTION
TORQUE
Plug, Drain/Fill . . . . . . . . . . . . . . . . . . . . . . 40 N·m
Nuts, Mounting . . . . . . . . . . . . . . . . . . . . . . 35 N·m
Switch, Indicator . . . . . . . . . . . . . . . . . . . . . 26 N·m
Fig. 1 Transfer Case Mounting
1 – MOUNTING STUDS
2 – TRANSFER CASE
3 – TRANSMISSION
XJ
TRANSMISSION AND TRANSFER CASE
21 - 5
2000 JEEP CHEROKEE
2000 JEEP CHEROKEE
TIRES AND WHEELS
TABLE OF CONTENTS
page
page
TIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
WHEELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TIRES
TABLE OF CONTENTS
page
page
DESCRIPTION AND OPERATION
TIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
RADIAL-PLY TIRES . . . . . . . . . . . . . . . . . . . . . . . . 2
SPARE TIRE–TEMPORARY . . . . . . . . . . . . . . . . . . 2
TIRE INFLATION PRESSURES . . . . . . . . . . . . . . . 2
TIRE PRESSURE FOR HIGH SPEED. . . . . . . . . . . 3
REPLACEMENT TIRES . . . . . . . . . . . . . . . . . . . . . 3
DIAGNOSIS AND TESTING
SERVICE PROCEDURES
ROTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
MATCH MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . 4
REPAIRING LEAKS . . . . . . . . . . . . . . . . . . . . . . . . 5
CLEANING AND INSPECTION
CLEANING TIRES . . . . . . . . . . . . . . . . . . . . . . . . . 6
SPECIFICATIONS
TIRE SIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DESCRIPTION AND OPERATION
TIRES
DESCRIPTION
Tires are designed and engineered for each specific
vehicle. They provide the best overall performance
for normal operation. The ride and handling charac-
teristics match the vehicle’s requirements. With
proper care they will give excellent reliability, trac-
tion, skid resistance, and tread life.
Driving habits have more effect on tire life than
any other factor. Careful drivers will obtain in most
cases, much greater mileage than severe use or care-
less drivers. A few of the driving habits which will
shorten the life of any tire are:
• Rapid acceleration
• Severe brake applications
• High speed driving
• Excessive speeds on turns
• Striking curbs and other obstacles
Radial-ply tires are more prone to irregular tread
wear. It is important to follow the tire rotation inter-
val shown in the section on Tire Rotation. This will
help to achieve a greater tread life.
TIRE IDENTIFICATION
Tire type, size, aspect ratio and speed rating are
encoded in the letters and numbers imprinted on the
side wall of the tire. Refer to the chart to decipher
the tire identification code (Fig. 1).
Performance tires have a speed rating letter after
the aspect ratio number.
The speed rating is not always printed on the tire
sidewall.
LETTER
SPEED RATING
S
180 km/h (112 mph)
T
190 km/h (118 mph)
U
200 km/h (124 mph)
H
210 km/h (130 mph)
V
240 km/h (149 mph)
W
270 km/h (168 mph)
Y
300 km/h (186 mph)
XJ
TIRES AND WHEELS
22 - 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст