Jeep Grand Cherokee WK. Manual — part 723
B1459-TELEMATICS MIRROR CONTROL CIRCUIT LOW (CONTINUED)
2.
(X793) MICROPHONE FEED CIRCUIT OPEN
Turn the ignition off.
Disconnect the Hands Free Module harness connector.
Disconnect the Inside Rear View Mirror C2 harness connector.
Measure the resistance of the (X793) Microphone Feed circuit
between the HFM connector and the inside rear view mirror connector.
Is the resistance below 5.0 ohms?
Yes
>> Go To 3
No
>> Repair the (X793) Microphone Feed circuit for an open.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).
3.
(X793) MICROPHONE FEED CIRCUIT SHORT TO GROUND
Measure the resistance between ground and the (X793) Microphone
Feed circuit.
Is the resistance below 100.0 ohms?
Yes
>> Repair the (X793) Microphone Feed circuit for short to
ground.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).
No
>> Go To 4
8T - 38
NAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICS
WK
B1459-TELEMATICS MIRROR CONTROL CIRCUIT LOW (CONTINUED)
4.
INSIDE REAR VIEW MIRROR
Replace the Inside Rear View Mirror in accordance with the service information.
Cycle the ignition switch from off to on at least 5 times, leaving the ignition on for a minimum of 90 seconds per
cycle.
Attempt to make a phone call with the system.
With the scan tool, read the active DTC’s.
Does the scan tool display this DTC as active?
Yes
>> Inspect the wiring and connectors for damage or shorted circuits. If ok, replace and program the Hands
Free Module in accordance with the service information.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).
No
>> Repair is complete.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).
WK
NAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICS
8T - 39
B1492–GENERAL MICROPHONE PERFORMANCE
8T - 40
NAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICS
WK
B1492–GENERAL MICROPHONE PERFORMANCE (CONTINUED)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
•
Set Condition:
The Hands Free Module detects a fault in any of the microphone circuits.
Possible Causes
(X712) MICROPHONE 1 IN (+) CIRCUIT OPEN
(X722) MICROPHONE 2 IN (+) CIRCUIT OPEN
(X792) MICROPHONE IN (-) CIRCUIT OPEN
(X712) (X722) (X792) MICROPHONE CIRCUITS SHORTED TO GROUND
(X712) (X722) (X792) MICROPHONE CIRCUITS SHORTED TO VOLTAGE
(X712) (X722) (X792) MICROPHONE CIRCUITS SHORTED TOGETHER
INSIDE REAR VIEW MIRROR
HANDS FREE MODULE
Diagnostic Test
1.
CHECK FOR ACTIVE DTC
With the scan tool, read the active DTC’s.
Cycle the ignition switch from off to on at least 5 times, leaving the ignition on for a minimum of 90 seconds per
cycle.
Attempt to make a phone call with the system.
With the scan tool, read the active DTC’s.
Does the scan tool display this DTC as active?
Yes
>> Go To 2
No
>> If the DTC is stored, check for an intermittent condition. Visually inspect the related wiring harness con-
nectors. Look for broken, bent, pushed out, or corroded terminals.
WK
NAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICS
8T - 41
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст