Jeep Grand Cherokee WK. Manual — part 1022
P0593-SPEED CONTROL SWITCH 2 CIRCUIT HIGH
9 - 684
ENGINE ELECTRICAL DIAGNOSTICS
WK
P0593-SPEED CONTROL SWITCH 2 CIRCUIT HIGH (CONTINUED)
For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition key on.
•
Set Condition:
Speed Control Switch No.2 input above the maximum acceptable voltage at the PCM. One trip fault.
Possible Causes
(V372) S/C SIGNAL NO.2 CIRCUIT SHORTED TO VOLTAGE
(V72) S/C SIGNAL NO.2 CIRCUIT SHORTED TO VOLTAGE
(V372) S/C SWITCH NO.2 SIGNAL CIRCUIT OPEN
(V72) S/C SWITCH NO.2 SIGNAL CIRCUIT OPEN
(V397) SWITCH RETURN CIRCUIT OPEN
(V937) SWITCH RETURN CIRCUIT OPEN
STEERING COLUMN CONTROL MODULE
SPEED CONTROL SWITCH
PCM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).
Diagnostic Test
1.
SPEED CONTROL SWITCH VOLTAGE HIGH
NOTE: Do not press any of the Speed Control Switch buttons.
Ignition on, engine not running.
With a scan tool, read the Speed Control voltage.
Is the Speed Control voltage above 4.8 volts?
Yes
>> Go To 2
No
>> Refer to the INTERMITTENT CONDITION Diagnostic Procedure.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
WK
ENGINE ELECTRICAL DIAGNOSTICS
9 - 685
P0593-SPEED CONTROL SWITCH 2 CIRCUIT HIGH (CONTINUED)
2.
SPEED CONTROL SWITCHES
Disconnect and remove the Speed Control Switches from the steering wheel.
Measure the resistance across each Speed Control Switch.
Monitor the ohmmeter while pressing each function button on each switch.
The following resistance specs are taken between terminals (V372) S/C Switch No.2 Signal and (V397) S/C Switch
Return circuits of the Switch when holding the switch button in the following position.
Not pressing any switch - 20.5 kohms
On/Off - 8.87 kohms
Set - 0.825 kohms
Coast - 0.47 kohms
Cancel - 3.92 kohms
Resume/Accel - 1.87 kohms
Does the function on the Speed Control Switches have the correct resistance value?
Yes
>> Go To 3
No
>> Replace the Speed Control Switch that had the incorrect resistance value.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
3.
STEERING COLUMN CONTROL MODULE
Disconnect the C1 and C3 Steering Column Control Module harness connectors per Service Information.
Measure the resistance of the (V397) Switch Return circuit between the C1 and C3 SCCM connections.
Measure the resistance of the (V372) S/C Switch No.2 Signal circuit between the C1 and C3 SCCM connections.
Was the resistance above 5.0 ohms for either circuit?
Yes
>> Replace the Steering Column Control Module per Service Information.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 4
4.
(V372) SIGNAL NO.2 CIRCUIT SHORTED TO BATTERY VOLTAGE
Measure the voltage on the (V372) S/C Signal No.2 circuit in the S/C
Switch harness connector.
Ignition on, engine not running.
Is the voltage above 0 volts?
Yes
>> Repair the short to battery voltage in the (V372) S/C Sig-
nal No.2 circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 5
9 - 686
ENGINE ELECTRICAL DIAGNOSTICS
WK
P0593-SPEED CONTROL SWITCH 2 CIRCUIT HIGH (CONTINUED)
5.
(V72) S/C SWITCH NO.2 SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
Turn the ignition off.
Disconnect the C3 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (V72) S/C Switch No.2 Signal circuit in the
C1 SCCM harness connector.
Is the voltage above 0 volts?
Yes
>> Repair the short to battery voltage in the (V72) S/C Switch
No.2 Signal circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 6
6.
(V372) S/C SWITCH NO.2 SIGNAL CIRCUIT OPEN
Turn the ignition off.
Measure the resistance of the (V372) S/C Switch No.2 Signal circuit
from the both Switch harness connectors to the C3 SCCM harness
connector.
Is the resistance below 5.0 ohms?
Yes
>> Go To 7
No
>> Repair the open in the (V372) S/C Switch No.2 Signal cir-
cuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
WK
ENGINE ELECTRICAL DIAGNOSTICS
9 - 687
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст