Jeep Grand Cherokee WK. Manual — part 717
B1415-HFM RIGHT AUDIO OUTPUT CIRCUIT LOW (CONTINUED)
4.
(X795) COMMON AUDIO OUTPUT CIRCUIT OPEN
Measure the resistance of the (X795) Common Audio Output circuit
between the HFM connector and the radio connector.
Is the resistance below 5.0 ohms?
Yes
>> Go To 5
No
>> Repair the (X795) Common Audio Output circuit for an
open.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).
5.
(X704) RIGHT AUDIO OUTPUT CIRCUIT SHORT TO (X795) COMMON AUDIO OUTPUT CIRCUIT
Measure the resistance between the (X704) Right Audio Output circuit
and the (X795) Common Audio Output circuit.
Is the resistance below 5.0 ohms?
Yes
>> Repair the (X704) Right Audio Output circuit for a short to
the (X795) Common Audio Output circuit.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).
No
>> Inspect the wiring and connectors for damage or shorted
circuits. If ok, replace and program the Hands Free Mod-
ule in accordance with the service information.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).
8T - 14
NAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICS
WK
B1416-HFM RIGHT AUDIO OUTPUT CIRCUIT HIGH
WK
NAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICS
8T - 15
B1416-HFM RIGHT AUDIO OUTPUT CIRCUIT HIGH (CONTINUED)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
•
Set Condition:
The Hands Free Module detects high voltage on the (X704) Right Audio Output circuit.
Possible Causes
(X704) RIGHT AUDIO OUTPUT CIRCUIT OPEN
(X795) COMMON AUDIO OUTPUT CIRCUIT OPEN
(X704) RIGHT AUDIO OUTPUT CIRCUIT SHORT TO VOLTAGE
HANDS FREE MODULE
Diagnostic Test
1.
CHECK FOR ACTIVE DTC
With the scan tool, read the active DTC’s.
Cycle the ignition switch from off to on at least 5 times, leaving the ignition on for a minimum of 90 seconds per
cycle.
With the scan tool, read the active DTC’s.
Does the scan tool display this DTC as active?
Yes
>> Go To 2
No
>> If the DTC is stored, check for an intermittent condition. Visually inspect the related wiring harness con-
nectors. Look for broken, bent, pushed out, or corroded terminals.
8T - 16
NAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICS
WK
B1416-HFM RIGHT AUDIO OUTPUT CIRCUIT HIGH (CONTINUED)
2.
(X704) RIGHT AUDIO OUTPUT CIRCUIT OPEN
Turn the ignition off.
Disconnect the Hands Free Module harness connector.
Disconnect the Radio C1 harness connector.
Measure the resistance of the (X704) Right Audio Output circuit
between the HFM connector and the radio connector.
Is the resistance below 5.0 ohms?
Yes
>> Go To 3
No
>> Repair the (X704) Right Audio Output circuit for an open
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).
3.
(X795) COMMON AUDIO OUTPUT CIRCUIT OPEN
Measure the resistance of the (X795) Common Audio Output circuit
between the HFM connector and the radio connector.
Is the resistance below 5.0 ohms?
Yes
>> Go To 4
No
>> Repair the (X795) Common Audio Output circuit for an
open.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).
WK
NAVIGATION/TELECOMMUNICATION - ELECTRICAL DIAGNOSTICS
8T - 17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст