Jeep Grand Cherokee WK. Manual — part 1080
P2118-ELECTRONIC THROTTLE CONTROL MOTOR CIRCUIT (CONTINUED)
6.
(K124) ETC POSITIVE CIRCUIT OPEN
Turn the ignition off.
Measure the resistance of the (K124) ETC Positive circuit from the
Throttle Body harness connector to the appropriate terminal of special
tool #8815.
Is the resistance below 5.0 ohms?
Yes
>> Go To 7
No
>> Repair the open in the (K124) ETC Positive circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
7.
(K124) ETC POSITIVE CIRCUIT SHORTED TO GROUND
Measure the resistance between ground and the (K124) ETC Positive
circuit between the appropriate terminals of special tool #8815.
Is the resistance below 100 ohms?
Yes
>> Repair the short to ground in the (K124) ETC Positive cir-
cuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 8
9 - 916
ENGINE ELECTRICAL DIAGNOSTICS
WK
P2118-ELECTRONIC THROTTLE CONTROL MOTOR CIRCUIT (CONTINUED)
8.
(K126) ETC NEGATIVE CIRCUIT OPEN
Measure the resistance of the (K126) ETC Negative circuit from the
Throttle Body harness connector to the appropriate terminal of special
tool #8815.
Is the resistance below 5.0 ohms?
Yes
>> Go To 9
No
>> Repair the open in the (K126) ETC Negative circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
9.
(K126) ETC NEGATIVE CIRCUIT SHORTED TO GROUND
Measure the resistance between ground and the (K126) ETC Negative
circuit between the appropriate terminals of special tool #8815.
Is the resistance below 100 ohms?
Yes
>> Repair the short to ground in the (K126) ETC Negative cir-
cuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 10
WK
ENGINE ELECTRICAL DIAGNOSTICS
9 - 917
P2118-ELECTRONIC THROTTLE CONTROL MOTOR CIRCUIT (CONTINUED)
10.
ETC MOTOR
NOTE: Take the following measurement using special tool #8815
to avoid possible damage to the Throttle Body harness connec-
tor.
Measure the resistance of the ETC Motor between the (K124) ETC
Positive circuit and the (K126) ETC Negative circuit at the appropriate
terminals of special tool #8815.
Is the resistance between 2.5 and 25 ohms at closed throttle?
Yes
>> Go To 11
No
>> Replace the Throttle Body Assembly. Disconnect the Bat-
tery when replacing the Throttle Body Assembly. After
installation is complete, use a scan tool and select the
ETC RELEARN function.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
11.
PCM
NOTE: Before continuing, check the PCM harness connector terminals for corrosion, damage, or terminal
push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay particular attention to all Power and
Ground circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Replace and program the Powertrain Control Module per Service Information.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
9 - 918
ENGINE ELECTRICAL DIAGNOSTICS
WK
P2122-ACCELERATOR PEDAL POSITION SENSOR 1 CIRCUIT LOW
WK
ENGINE ELECTRICAL DIAGNOSTICS
9 - 919
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст