Jeep Grand Cherokee WK. Manual — part 664
5. Remove the screw (3) that secures the seat belt
turning loop (4) to the height adjuster (10).
6. Remove the seat belt turning loop from the height
adjuster.
7. Remove the upper trim from the inside of the B-pil-
lar (9). (Refer to 23 - BODY/INTERIOR/B-PILLAR
UPPER TRIM - REMOVAL).
8. Unsnap and remove the cover (5) from above the
seat belt opening in the B-pillar trim (2).
9. Remove the trim from the lower B-pillar. (Refer to
23 - BODY/INTERIOR/B-PILLAR LOWER TRIM -
REMOVAL).
10. Pull the front seat belt turning loop and lower
anchor through the seat belt opening in the lower
B-pillar trim.
11. Remove the screw (7) that secures the retractor
(6) lower bracket to the base of the inner B-pillar.
12. Remove the front seat belt and retractor from the
vehicle as a unit.
REAR OUTBOARD
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
1. Remove the rear seat cushion from the vehicle.
(Refer to 23 - BODY/SEATS/REAR SEAT CUSH-
ION - REMOVAL).
2. Loosen the screw (3) that secures the rear out-
board seat belt lower anchor and the rear seat
back bracket to the rear floor panel.
3. Disengage the lower anchor from the loosened
screw.
4. Remove the upper trim from the inside of the C-pil-
lar. (Refer to 23 - BODY/INTERIOR/C-PILLAR
TRIM - REMOVAL).
5. Disengage the seat belt lower anchor from the seat
belt opening in the upper C-pillar trim.
6. Remove the trim (5) from the quarter inner panel.
(Refer to 23 - BODY/INTERIOR/QUARTER TRIM
PANEL - REMOVAL).
7. Remove the screw (2) that secures the seat belt
turning loop to the upper C-pillar.
8O - 478
RESTRAINTS - SERVICE INFORMATION
WK
8. Remove the seat belt turning loop from the upper C-pillar.
9. Remove the screw (4) that secures the retractor (1) to the lower C-pillar.
10. Disengage the retractor locator tab from the slot in the lower C-pillar.
11. Remove the rear outboard seat belt and retractor from the lower C-pillar as a unit.
REAR CENTER
WARNING: During and following any seat belt or child restraint anchor service, carefully inspect all seat
belts, buckles, mounting hardware, retractors, tether straps, and anchors for proper installation, operation,
or damage. Replace any belt that is cut, frayed, or torn. Straighten any belt that is twisted. Tighten any
loose fasteners. Replace any belt that has a damaged or inoperative buckle or retractor. Replace any belt
that has a bent or damaged latch plate or anchor plate. Replace any child restraint anchor or the unit to
which the anchor is integral that has been bent or damaged. Never attempt to repair a seat belt or child
restraint component. Always replace damaged or faulty seat belt and child restraint components with the
correct, new and unused replacement parts listed in the DaimlerChrysler Mopar Parts Catalog.
1. Remove the left rear seat back panel (4) from the
vehicle. (Refer to 23 - BODY/SEATS/REAR SEAT
BACK - REMOVAL).
2. Remove the trim from the left rear seat back.
(Refer to 23 - BODY/SEATS/REAR SEAT BACK
COVER - REMOVAL).
3. Disengage the seat belt lower anchor through the
web guide loop integral to the top of the seat back
panel.
4. Disengage the retractor lock cable (2) end fitting
from the seat back latch mechanism (3) on the
upper outboard corner of the seat back panel.
5. Disengage the lock cable from the back panel
between the latch and the retractor (1).
6. Remove the screw (2) from the back of the seat
back panel (1) that secures the retractor.
7. Remove the rear center seat belt and retractor unit
from the front of the left seat back panel.
WK
RESTRAINTS - SERVICE INFORMATION
8O - 479
INSTALLATION
FRONT
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
1. Be certain that the retractor shield (8) is properly
installed in the inner B-pillar (9) and in good condi-
tion before installing the retractor.
2. Position the retractor (6) into the vehicle as a unit.
3. Install and tighten the screw (7) that secures the
retractor lower bracket to the base of the inner
B-pillar. Tighten the screw to 39 N·m (29 ft. lbs.).
4. Route the front seat belt turning loop (4) and lower
anchor through the seat belt opening in the lower
B-pillar trim (2).
5. Reinstall the lower trim onto the B-pillar. (Refer to
23 - BODY/INTERIOR/B-PILLAR LOWER TRIM -
INSTALLATION).
6. Reinstall the cover (5) into the upper seat belt
opening in the B-pillar trim.
7. Reinstall the upper trim onto the inside of the B-pil-
lar. (Refer to 23 - BODY/INTERIOR/B-PILLAR
UPPER TRIM - INSTALLATION).
8. Position the seat belt turning loop onto the height
adjuster (10) on the upper B-pillar. Be certain that
the seat belt webbing between the retractor and
the turning loop is not twisted.
9. Install and tighten the screw (5) that secures the
turning loop to the height adjuster. Tighten the screw to 39 N·m (29 ft. lbs.).
8O - 480
RESTRAINTS - SERVICE INFORMATION
WK
10. Insert the upper tabs of the turning loop trim cover
into the slots of the height adjuster on the upper
B-pillar, then lower the bottom of the cover and
use hand pressure to press firmly and evenly on
the cover until it snaps into place.
11. Position the seat belt lower anchor to the mount-
ing hole on the outboard side of the front seat
cushion frame. Be certain that the seat belt web-
bing between the turning loop and the lower
anchor is not twisted.
12. Install and tighten the screw (2) that secures the
lower anchor to the seat. Tighten the screw to 39
N·m (29 ft. lbs.).
13. Reinstall the lower anchor cover (1) onto the front
seat cushion outboard side shield.
REAR OUTBOARD
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
WK
RESTRAINTS - SERVICE INFORMATION
8O - 481
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст