Jeep Wrangler TJ. Manual — part 226
(12) Remove pinion depth shim/oil slinger from
pinion shaft and record thickness.
INSTALLATION
NOTE: Pinion depth shims are placed between the
rear pinion bearing cone and pinion gear to achieve
proper ring and pinion gear mesh. If ring and pinion
gears are reused, the original pinion depth shim
can be used. Refer to Adjustments (Pinion Gear
Depth) to select the proper shim thickness if ring
and pinion gears are replaced.
(1) Apply Mopar Door Ease stick or equivalent
lubricant to outside surface of bearing cups.
(2) Install rear pinion bearing cup with Installer
D-146 and Handle C-4171 (Fig. 75).
(3) Install front pinion bearing cup with Installer
D-144 and Handle C-4171 (Fig. 76).
(4) Install pinion front bearing, oil slinger. Apply a
light coating of gear lubricant on the lip of pinion
seal.
(5) Install pinion seal with an appropriate installer
(Fig. 77).
(6) Install proper thickness depth shim on the pin-
ion gear.
Fig. 75 REAR PINION BEARING CUP
1 - INSTALLER
2 - HANDLE
Fig. 76 FRONT PINION BEARING CUP INSTALLER
1 - INSTALLER
2 - HANDLE
Fig. 77 PINION SEAL INSTALLER
1 - HANDLE
2 - INSTALLER
TJ
FRONT AXLE - 216FBI
3 - 81
PINION GEAR/RING GEAR (Continued)
(7) Install rear bearing and oil slinger, if equipped
on pinion gear with Installer W-262 (Fig. 78).
(8) Install pinion gear in housing.
(9) Install pinion preload shims (Fig. 79)
(10) Install yoke with Installer W-162-D and Yoke
Holder 6719A (Fig. 80).
(11) Install yoke washer and a new nut on the
pinion gear. Tighten the nut to specification (Fig. 81).
Fig. 78 REAR PINION BEARING
1 - PRESS
2 - INSTALLER
3 - PINION GEAR
4 - PINION BEARING
Fig. 79 PINION PRELOAD SHIMS
1 - PRELOAD SHIMS
2 - FRONT BEARING CUP
3 - SLINGER
4 - PINION YOKE
5 - WASHER
6 - PINION NUT
7 - PINION OIL SEAL
8 - FRONT PINION BEARING
Fig. 80 PINION YOKE INSTALLER
1 - INSTALLER
2 - YOKE HOLDER
Fig. 81 TIGHTENING PINION NUT
1 - PINION YOKE
2 - YOKE HOLDING
3 - DIFFERENTIAL HOUSING
3 - 82
FRONT AXLE - 216FBI
TJ
PINION GEAR/RING GEAR (Continued)
(12) Check bearing preload torque with an inch
pound torque wrench (Fig. 82). The torque to rotate
the pinion gear should be:
• Original Bearings: 1 to 2 N·m (10 to 20 in. lbs.).
• New Bearings: 2.3 to 4.5 N·m (20 to 40 in. lbs.).
(13) Invert differential case in a vise and start two
ring gear bolts. This will provide case-to-ring gear
bolt hole alignment.
(14) Install new ring gear bolts and alternately
tighten to 136 N·m (100 ft. lbs.). (Fig. 83).
CAUTION: Never reuse the ring gear bolts. Failure
to heed caution may result in damage.
(15) Install differential in axle housing and verify
gear mesh and contact pattern. Refer to Adjustments
(Gear Contact Pattern).
Fig. 82 PINION ROTATION TORQUE
1 - PINION YOKE
2 - INCH POUND TORQUE WRENCH
Fig. 83 RING GEAR INSTALLATION
1 - TORQUE WRENCH
2 - RING GEAR BOLT
3 - RING GEAR
4 - CASE
TJ
FRONT AXLE - 216FBI
3 - 83
PINION GEAR/RING GEAR (Continued)
REAR AXLE - 194RBI
TABLE OF CONTENTS
page
page
REAR AXLE - 194RBI
. . . . . . . . . . . . . . . . 84
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
. . . . . . . . . . . . . . . . . . . . . . . . . 88
. . . . . . . . . . . . . . . . . . . . . . . . 89
. . . . . . . . . . . . . . . . . . . . . . . . . . 96
. . . . . . . . . . . . . . . . . . . . . . . 97
AXLE SHAFTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
. . . . . . . . . . . . . . . . . . . . . . . . 100
AXLE SHAFT SEALS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
. . . . . . . . . . . . . . . . . . . . . . . . 100
AXLE BEARINGS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
. . . . . . . . . . . . . . . . . . . . . . . . 101
PINION SEAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
. . . . . . . . . . . . . . . . . . . . . . . . 102
COLLAPSIBLE SPACER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
. . . . . . . . . . . . . . . . . . . . . . . . 103
DIFFERENTIAL COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
. . . . . . . . . . . . . . . . . . . . . . . . 105
DIFFERENTIAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
. . . . . . . . . . . . . . . . . . . . . . . . 106
. . . . . . . . . . . . . . . . . . . . . . . . . . . 106
. . . . . . . . . . . . . . . . . . . . . . . . 107
DIFFERENTIAL - TRAC-LOK
. . . . . . . . . . . . . . . . . . . . . . . . 108
. . . . . . . . . . . . . . . . . . . . . . . . . . 108
. . . . . . . . . . . . . . . 108
. . . . . . . . . . . . . . . . . . . . . . . . 109
. . . . . . . . . . . . . . . . . . . . . . . . . . . 110
DIFFERENTIAL CASE BEARINGS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
. . . . . . . . . . . . . . . . . . . . . . . . 113
PINION GEAR/RING GEAR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
. . . . . . . . . . . . . . . . . . . . . . . . 115
REAR AXLE - 194RBI
DIAGNOSIS AND TESTING
GEAR NOISE
Axle gear noise can be caused by insufficient lubri-
cant, incorrect backlash, incorrect pinion depth, tooth
contact, worn/damaged gears, or the carrier housing
not having the proper offset and squareness.
Gear noise usually happens at a specific speed
range. The noise can also occur during a specific type
of driving condition. These conditions are accelera-
tion, deceleration, coast, or constant load.
When road testing, first warm-up the axle fluid by
driving the vehicle at least 5 miles and then acceler-
ate the vehicle to the speed range where the noise is
the greatest. Shift out-of-gear and coast through the
peak-noise range. If the noise stops or changes
greatly:
• Check for insufficient lubricant.
• Incorrect ring gear backlash.
• Gear damage.
Differential side gears and pinions can be checked
by turning the vehicle. They usually do not cause
noise during straight-ahead driving when the gears
are unloaded. The side gears are loaded during vehi-
cle turns. A worn pinion shaft can also cause a snap-
ping or a knocking noise.
BEARING NOISE
The axle shaft, differential and pinion bearings can
all produce noise when worn or damaged. Bearing
noise can be either a whining, or a growling sound.
Pinion bearings have a constant-pitch noise. This
noise changes only with vehicle speed. Pinion bearing
noise will be higher pitched because it rotates at a
faster rate. Drive the vehicle and load the differen-
tial. If bearing noise occurs, the rear pinion bearing
is the source of the noise. If the bearing noise is
heard during a coast, the front pinion bearing is the
source.
Worn or damaged differential bearings usually pro-
duce a low pitch noise. Differential bearing noise is
similar to pinion bearing noise. The pitch of differen-
tial bearing noise is also constant and varies only
with vehicle speed.
Axle shaft bearings produce noise and vibration
when worn or damaged. The noise generally changes
when the bearings are loaded. Road test the vehicle.
Turn the vehicle sharply to the left and to the right.
This will load the bearings and change the noise
3 - 84
REAR AXLE - 194RBI
TJ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст