Jeep Wrangler TJ. Manual — part 344
TERMINOLOGY
This is a list of terms and definitions used in the
wiring diagrams.
LHD . . . . . . . . . . . . . . . . . Left Hand Drive Vehicles
RHD . . . . . . . . . . . . . . . Right Hand Drive Vehicles
ATX . . Automatic Transmissions-Front Wheel Drive
MTX . . . Manual Transmissions-Front Wheel Drive
AT . . . . Automatic Transmissions-Rear Wheel Drive
MT . . . . . Manual Transmissions-Rear Wheel Drive
SOHC . . . . . . . . . . . Single Over Head Cam Engine
DOHC . . . . . . . . . . Double Over Head Cam Engine
Export . . Vehicles Built For Sale In Markets Other
Than North America
Except Export . . . . Vehicles Built For Sale In North
America
DESCRIPTION - CIRCUIT INFORMATION
Each wire shown in the diagrams contains a code
which identifies the main circuit, part of the main
circuit, gage of wire, and color (Fig. 4).
WIRE COLOR CODE CHART
COLOR CODE
COLOR
BL
BLUE
BK
BLACK
BR
BROWN
DB
DARK BLUE
DG
DARK GREEN
GY
GRAY
LB
LIGHT BLUE
LG
LIGHT GREEN
OR
ORANGE
PK
PINK
RD
RED
TN
TAN
VT
VIOLET
WT
WHITE
YL
YELLOW
*
WITH TRACER
Fig. 4 WIRE CODE IDENTIFICATION
1 - COLOR OF WIRE (LIGHT BLUE WITH YELLOW TRACER
2 - GAGE OF WIRE (18 GAGE)
3 - PART OF MAIN CIRCUIT (VARIES DEPENDING ON
EQUIPMENT)
4 - MAIN CIRCUIT IDENTIFICATION
TJ
8W-01 WIRING DIAGRAM INFORMATION
8W - 01 - 5
WIRING DIAGRAM INFORMATION (Continued)
DESCRIPTION - CIRCUIT FUNCTIONS
All circuits in the diagrams use an alpha/numeric
code to identify the wire and it’s function. To identify
which circuit code applies to a system, refer to the
Circuit Identification Code Chart. This chart shows
the main circuits only and does not show the second-
ary codes that may apply to some models.
CIRCUIT IDENTIFICATION CODE CHART
CIRCUIT
FUNCTION
A
BATTERY FEED
B
BRAKE CONTROLS
C
CLIMATE CONTROLS
D
DIAGNOSTIC CIRCUITS
E
DIMMING ILLUMINATION
CIRCUITS
F
FUSED CIRCUITS
G
MONITORING CIRCUITS
(GAUGES)
H
MULTIPLE
I
NOT USED
J
OPEN
K
POWERTRAIN CONTROL
MODULE
L
EXTERIOR LIGHTING
M
INTERIOR LIGHTING
N
MULTIPLE
O
NOT USED
P
POWER OPTION (BATTERY
FEED)
Q
POWER OPTIONS (IGNITION
FEED)
R
PASSIVE RESTRAINT
S
SUSPENSION/STEERING
T
TRANSMISSION/TRANSAXLE/
TRANSFER CASE
U
OPEN
V
SPEED CONTROL, WIPER/
WASHER
W
WIPERS
X
AUDIO SYSTEMS
Y
OPEN
Z
GROUNDS
DESCRIPTION - SECTION IDENTIFICATION AND
INFORMATION
The wiring diagrams are grouped into individual
sections. If a component is most likely found in a par-
ticular group, it will be shown complete (all wires,
connectors, and pins) within that group. For exam-
ple, the Auto Shutdown Relay is most likely to be
found in Group 30, so it is shown there complete. It
can, however, be shown partially in another group if
it contains some associated wiring.
Splice diagrams in Section 8W-70 show the entire
splice and provide references to other sections the
splices serves. Section 8W-70 only contains splice dia-
grams that are not shown in their entirety some-
where else in the wiring diagrams.
Section 8W-80 shows each connector and the cir-
cuits involved with that connector. The connectors
are identified using the name/number on the dia-
gram pages.
WIRING SECTION CHART
GROUP
TOPIC
8W-01 thru
8W-09
General information and Diagram
Overview
8W-10 thru
8W-19
Main Sources of Power and
Vehicle Grounding
8W-20 thru
8W-29
Starting and Charging
8W-30 thru
8W-39
Powertrain/Drivetrain Systems
8W-40 thru
8W-49
Body Electrical items and A/C
8W-50 thru
8W-59
Exterior Lighting, Wipers and
Trailer Tow
8W-60 thru
8W-69
Power Accessories
8W-70
Splice Information
8W-80
Connector Pin Outs
8W-91
Connector, Ground and Splice
Locations
8W - 01 - 6
8W-01 WIRING DIAGRAM INFORMATION
TJ
WIRING DIAGRAM INFORMATION (Continued)
DESCRIPTION - CONNECTOR, GROUND AND
SPLICE INFORMATION
CAUTION: Not all connectors are serviced. Some
connectors are serviced only with a harness. A typ-
ical example might be the Supplemental Restraint
System connectors. Always check parts availability
before attempting a repair.
IDENTIFICATION
In-line connectors are identified by a number, as
follows:
• In-line connectors located in the engine compart-
ment are C100 series numbers
• In-line connectors located in the Instrument
Panel area are C200 series numbers.
• In-line connectors located in the body are C300
series numbers.
• Jumper harness connectors are C400 series
numbers.
• Grounds and ground connectors are identified
with a “G” and follow the same series numbering as
the in-line connectors.
• Splices are identified with an “S” and follow the
same series numbering as the in-line connectors.
• Component connectors are identified by the com-
ponent name instead of a number. Multiple connec-
tors on a component use a C1, C2, etc. identifier.
LOCATIONS
Section
8W-91
contains
connector/ground/splice
location illustrations. The illustrations contain the
connector name (or number)/ground number/splice
number and component identification. Connector/
ground/splice location charts in section 8W-91 refer-
ence the figure numbers of the illustrations.
The abbreviation T/O is used in the component
location section to indicate a point in which the wir-
ing harness branches out to a component. The abbre-
viation N/S means Not Shown in the illustrations
WARNINGS - GENERAL
WARNINGS provide information to prevent per-
sonal injury and vehicle damage. Below is a list of
general warnings that should be followed any time a
vehicle is being serviced.
WARNING: ALWAYS WEAR SAFETY GLASSES FOR
EYE PROTECTION.
WARNING: USE SAFETY STANDS ANYTIME A PRO-
CEDURE REQUIRES BEING UNDER A VEHICLE.
WARNING: BE SURE THAT THE IGNITION SWITCH
ALWAYS IS IN THE OFF POSITION, UNLESS THE
PROCEDURE REQUIRES IT TO BE ON.
WARNING:
SET
THE
PARKING
BRAKE
WHEN
WORKING
ON
ANY
VEHICLE.
AN
AUTOMATIC
TRANSMISSION SHOULD BE IN PARK. A MANUAL
TRANSMISSION SHOULD BE IN NEUTRAL.
WARNING: OPERATE THE ENGINE ONLY IN A
WELL-VENTILATED AREA.
WARNING: KEEP AWAY FROM MOVING PARTS
WHEN THE ENGINE IS RUNNING, ESPECIALLY THE
FAN AND BELTS.
WARNING: TO PREVENT SERIOUS BURNS, AVOID
CONTACT WITH HOT PARTS SUCH AS THE RADIA-
TOR, EXHAUST MANIFOLD(S), TAIL PIPE, CATA-
LYTIC CONVERTER AND MUFFLER.
WARNING: DO NOT ALLOW FLAME OR SPARKS
NEAR
THE
BATTERY.
GASES
ARE
ALWAYS
PRESENT IN AND AROUND THE BATTERY.
WARNING: ALWAYS REMOVE RINGS, WATCHES,
LOOSE HANGING JEWELRY AND AVOID LOOSE
CLOTHING.
DIAGNOSIS AND TESTING - WIRING HARNESS
TROUBLESHOOTING TOOLS
When diagnosing a problem in an electrical circuit
there are several common tools necessary. These tools
are listed and explained below.
• Jumper Wire - This is a test wire used to con-
nect two points of a circuit. It can be used to bypass
an open in a circuit.
WARNING: NEVER USE A JUMPER WIRE ACROSS
A
LOAD,
SUCH
AS
A
MOTOR,
CONNECTED
BETWEEN A BATTERY FEED AND GROUND.
• Voltmeter - Used to check for voltage on a cir-
cuit. Always connect the black lead to a known good
ground and the red lead to the positive side of the
circuit.
CAUTION: Most of the electrical components used
in today’s vehicles are Solid State. When checking
voltages in these circuits, use a meter with a 10 -
megohm or greater impedance rating.
TJ
8W-01 WIRING DIAGRAM INFORMATION
8W - 01 - 7
WIRING DIAGRAM INFORMATION (Continued)
• Ohmmeter - Used to check the resistance
between two points of a circuit. Low or no resistance
in a circuit means good continuity.
CAUTION: Most of the electrical components used
in today’s vehicles are Solid State. When checking
resistance in these circuits use a meter with a 10 -
megohm or greater impedance rating. In addition,
make sure the power is disconnected from the cir-
cuit. Circuits that are powered up by the vehicle’s
electrical system can cause damage to the equip-
ment and provide false readings.
• Probing Tools - These tools are used for probing
terminals in connectors (Fig. 5). Select the proper
size tool from Special Tool Package 6807, and insert
it into the terminal being tested. Use the other end
of the tool to insert the meter probe.
INTERMITTENT AND POOR CONNECTIONS
Most intermittent electrical problems are caused
by faulty electrical connections or wiring. It is also
possible for a sticking component or relay to cause a
problem. Before condemning a component or wiring
assembly, check the following items.
• Connectors are fully seated
• Spread terminals, or terminal push out
• Terminals in the wiring assembly are fully
seated into the connector/component and locked into
position
• Dirt or corrosion on the terminals. Any amount of
corrosion or dirt could cause an intermittent problem
• Damaged connector/component casing exposing
the item to dirt or moisture
• Wire insulation that has rubbed through causing
a short to ground
• Some or all of the wiring strands broken inside
of the insulation
• Wiring broken inside of the insulation
TROUBLESHOOTING WIRING PROBLEMS
When troubleshooting wiring problems there are
six steps which can aid in the procedure. The steps
are listed and explained below. Always check for non-
factory items added to the vehicle before doing any
diagnosis. If the vehicle is equipped with these items,
disconnect them to verify these add-on items are not
the cause of the problem.
(1) Verify the problem.
(2) Verify any related symptoms. Do this by per-
forming operational checks on components that are
in the same circuit. Refer to the wiring diagrams.
(3) Analyze the symptoms. Use the wiring dia-
grams to determine what the circuit is doing, where
the problem most likely is occurring and where the
diagnosis will continue.
(4) Isolate the problem area.
(5) Repair the problem area.
(6) Verify the proper operation. For this step,
check for proper operation of all items on the
repaired circuit. Refer to the wiring diagrams.
STANDARD PROCEDURE
STANDARD PROCEDURE - ELECTROSTATIC
DISCHARGE (ESD) SENSITIVE DEVICES
All ESD sensitive components are solid state and a
symbol (Fig. 6) is used to indicate this. When han-
dling any component with this symbol, comply with
the following procedures to reduce the possibility of
electrostatic charge build up on the body and inad-
vertent discharge into the component. If it is not
known whether the part is ESD sensitive, assume
that it is.
(1) Always touch a known good ground before han-
dling the part. This should be repeated while han-
dling the part and more frequently after sliding
across a seat, sitting down from a standing position,
or walking a distance.
(2) Avoid touching electrical terminals of the part,
unless instructed to do so by a written procedure.
(3) When using a voltmeter, be sure to connect the
ground lead first.
(4) Do not remove the part form it’s protective
packing until it is time to install the part.
(5) Before removing the part from it’s pakage,
ground the pakage to a known good ground on the
vehicle.
Fig. 5 PROBING TOOL
1 - SPECIAL TOOL 6801
2 - PROBING END
Fig. 6 ELECTROSTATIC DISCHARGE SYMBOL
8W - 01 - 8
8W-01 WIRING DIAGRAM INFORMATION
TJ
WIRING DIAGRAM INFORMATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст