Jeep Wrangler TJ. Manual — part 279
Schedule
Condition
Expected Operation
Super Overheat
Oil temperature above 260° F
– All
9
Overheat
9
shift schedule
features apply
– 2nd gear PEMCC above 22 mph
– Above 22 mph the torque
converter will not unlock unless the
throttle is closed or if a wide open
throttle 2nd PEMCC to 1 kickdown
is made
STANDARD PROCEDURE - TCM QUICK LEARN
The quick learn procedure requires the use of the
scan tool.
This program allows the electronic transmission
system to recalibrate itself. This will provide the
proper transmission operation. The quick learn pro-
cedure should be performed if any of the following
procedures are performed:
• Transmission Assembly Replacement
• Transmission Control Module Replacement
• Solenoid Pack Replacement
• Clutch Plate and/or Seal Replacement
• Valve Body Replacement or Recondition
To perform the Quick Learn Procedure, the follow-
ing conditions must be met:
• The brakes must be applied
• The engine speed must be above 500 rpm
• The throttle angle (TPS) must be less than 3
degrees
• The shift lever position must stay in PARK until
prompted to shift to overdrive
• The shift lever position must stay in overdrive
after the Shift to Overdrive prompt until the scan
tool indicates the procedure is complete.
• The calculated oil temperature must be above
60° and below 200°
TJ
ELECTRONIC CONTROL MODULES
8E - 17
TRANSMISSION CONTROL MODULE (Continued)
ENGINE SYSTEMS
TABLE OF CONTENTS
page
page
STARTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
BATTERY SYSTEM
TABLE OF CONTENTS
page
page
BATTERY SYSTEM
. . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DIAGNOSIS AND TESTING - BATTERY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . 6
BATTERY
. . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DIAGNOSIS AND TESTING - BATTERY
CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
INDICATOR TEST . . . . . . . . . . . . . . . . . . . . . 10
STANDARD PROCEDURE - OPEN-CIRCUIT
VOLTAGE TEST . . . . . . . . . . . . . . . . . . . . . . . 11
STANDARD PROCEDURE - IGNITION-OFF
DRAW TEST . . . . . . . . . . . . . . . . . . . . . . . . . 11
STANDARD PROCEDURE - USING MICRO
BATTERY TESTER . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . 14
BATTERY HOLDDOWN
. . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 15
BATTERY CABLES
. . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DIAGNOSIS AND TESTING - BATTERY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 18
BATTERY TRAY
. . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . 20
BATTERY SYSTEM
DESCRIPTION
A single 12-volt battery is standard factory-in-
stalled equipment on this model. All of the compo-
nents of the battery system are located within the
engine compartment of the vehicle. The battery sys-
tem for this vehicle covers the following related com-
ponents, which are covered in further detail later in
this section of the service manual:
• Battery - The storage battery provides a reli-
able means of storing a renewable source of electrical
energy within the vehicle.
• Battery Cable - The battery cables connect the
battery terminal posts to the vehicle electrical sys-
tem.
• Battery Holddown - The battery holddown
hardware secures the battery in the battery tray in
the engine compartment.
TJ
ENGINE SYSTEMS
8F - 1
• Battery Tray - The battery tray provides a
secure mounting location in the vehicle for the bat-
tery and an anchor point for the battery holddown
hardware.
For battery system maintenance schedules and
jump starting procedures, see the owner’s manual in
the vehicle glove box. Optionally, refer to the Lubri-
cation and Maintenance section of this manual for
the recommended battery maintenance schedules and
for the proper battery jump starting procedure. While
battery charging can be considered a maintenance
procedure,
the
battery
charging
procedure
and
related information are located later in this section of
this service manual. This was done because the bat-
tery must be fully-charged before any battery system
diagnosis or testing procedures can be performed.
OPERATION
The battery system is designed to provide a safe,
efficient, reliable and mobile means of delivering and
storing electrical energy. This electrical energy is
required to operate the engine starting system, as
well as to operate many of the other vehicle acces-
sory systems for limited durations while the engine
and/or the charging system are not operating. The
battery system is also designed to provide a reserve
of electrical energy to supplement the charging sys-
tem for short durations while the engine is running
and the electrical current demands of the vehicle
exceed the output of the charging system. In addition
to delivering, and storing electrical energy for the
vehicle, the battery system serves as a capacitor and
voltage stabilizer for the vehicle electrical system. It
absorbs most abnormal or transient voltages caused
by the switching of any of the electrical components
or circuits in the vehicle.
DIAGNOSIS AND TESTING - BATTERY SYSTEM
The battery, starting, and charging systems in the
vehicle operate with one another and must be tested
as a complete system. In order for the engine to start
and the battery to maintain its charge properly, all of
the components that are used in these systems must
perform within specifications. It is important that
the battery, starting, and charging systems be thor-
oughly tested and inspected any time a battery needs
to be charged or replaced. The cause of abnormal bat-
tery discharge, overcharging or early battery failure
must be diagnosed and corrected before a battery is
replaced and before a vehicle is returned to service.
The service information for these systems has been
separated within this service manual to make it eas-
ier to locate the specific information you are seeking.
However, when attempting to diagnose any of these
systems, it is important that you keep their interde-
pendency in mind.
The diagnostic procedures used for the battery,
starting, and charging systems include the most
basic conventional diagnostic methods, to the more
sophisticated On-Board Diagnostics (OBD) built into
the Powertrain Control Module (PCM). Use of an
induction-type milliampere ammeter, a volt/ohmme-
ter, a battery charger, a carbon pile rheostat (load
tester) and a 12-volt test lamp may be required. All
OBD-sensed systems are monitored by the PCM.
Each monitored circuit is assigned a Diagnostic Trou-
ble Code (DTC). The PCM will store a DTC in elec-
tronic memory for any failure it detects. Refer to
Charging System for the proper charging system on-
board diagnostic test procedures.
MICRO 420 BATTERY TESTER
The
Micro
420
automotive
battery
tester
is
designed to help the dealership technicians diagnose
a defective battery. Follow the instruction manual
supplied with the tester to properly diagnose a vehi-
cle. If the instruction manual is not available refer to
the
standard
procedure
in
this
section,
which
includes the directions for using the Micro 420 bat-
tery tester.
8F - 2
BATTERY SYSTEM
TJ
BATTERY SYSTEM (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст