Jeep Wrangler TJ. Manual — part 459
Fig.
8
FRAME
SIDE
VIEW
L
W
B
TJ
FRAME & BUMPERS
13 - 7
FRAME (Continued)
Fig.
9
FRAME
T
O
P
VIEW
L
W
B
13 - 8
FRAME & BUMPERS
TJ
FRAME (Continued)
TRANSFER CASE SKID PLATE
REMOVAL
NOTE: The transmission and transfer case cross-
member is integrated with the transfer case skid
plate.
WARNING: THE TRANSFER CASE AND TRANSMIS-
SION ARE SUPPORTED BY THE TRANSFER CASE
SKID PLATE. BEFORE REMOVING THE TRANSFER
CASE SKID PLATE, ENSURE THAT THE TRANSMIS-
SION IS PROPERLY SUPPORTED.
(1) Raise
and
support
the
vehicle.
(Refer
to
LUBRICATION
&
MAINTENANCE/HOISTING
-
STANDARD PROCEDURE)
(2) Remove
the
transmission
skid
plate,
if
equipped. (Refer to 13 - FRAME & BUMPERS/
FRAME/FRONT SKID PLATE - REMOVAL)
(3) Support the transmission with a suitable lifting
device.
(4) Remove the nuts attaching the transmission
mount to the skid plate. (Fig. 10)
(5) Remove the bolts attaching the skid plate to
the frame and remove the skid plate. (Fig. 11)
INSTALLATION
(1) Position the skid plate on the vehicle.
(2) Install the bolts attaching the skid plate to the
frame and tighten to 74 N·m (55 ft. lbs.).
(3) Install the nuts attaching the transmission
mount to the skid plate and tighten to 35 N·m (26 ft.
lbs.).
(4) Install the transmission skid plate. (Refer to 13
-
FRAME
&
BUMPERS/FRAME/FRONT
SKID
PLATE - INSTALLATION)
Fig. 10 TRANSMISSION MOUNT (Auto shown,
manual similar)
1 - TRANSMISSION ASSEMBLY
2 - SUPPORT BRACKET BOLTS (4)
3 - TRANSMISSION MOUNT
4 - SKID PLATE/CROSSMEMBER NUTS (4)
5 - SKID PLATE/CROSSMEMBER
6 - MOUNT NUTS (4)
7 - SUPPORT BRACKET
Fig. 11 TRANSFER CASE SKID PLATE
1 - SKID PLATE
2 - BOLTS
3 - FRAME
TJ
FRAME & BUMPERS
13 - 9
FUEL TANK SKID PLATE
REMOVAL
(1) Position a support under the fuel tank skid
plate.
(2) Remove the protective caps from the end of the
strap studs.
(3) Remove the nuts that attach the skid plate to
the straps and to the crossmembers (Fig. 12).
(4) Separate the fuel tank strap from the skid
plate.
(5) Support the fuel tank and remove the skid
plate from the vehicle.
INSTALLATION
(1) Attach the skid plate to the fuel tank strap.
(2) Position and support the skid plate under the
fuel tank.
(3) Install the nuts to attach the skid plate to the
straps and to the frame crossmembers. Tighten the
fuel tank strap nuts to 5 N·m (40 in. lbs.). Tighten
the skid plate-to-crossmember nuts with 16 N·m (138
in. lbs.).
(4) Install the protective caps on the end of the
strap studs.
(5) Remove the support from under the skid plate.
FRONT TOW HOOK
REMOVAL
(1) Remove the torx bolts that attach the tow hook
to the bumper (Fig. 13).
(2) Separate the tow hook from the bumper.
INSTALLATION
(1) Position the tow hook on the bumper.
(2) Install the torx bolts that attach the tow hook
to the bumper and tighten to 108 N·m (80 ft. lbs.).
Fig. 12 FUEL TANK SKID PLATE
1 - STRAP
2 - FRAME
3 - SKID PLATE
4 - PROTECTIVE CAP
5 - FUEL TANK
Fig. 13 FRONT TOW HOOK
1 - FRAME
2 - BUMPER
3 - TOW HOOK
13 - 10
FRAME & BUMPERS
TJ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст