Jeep Liberty (2012 year). Instruction — part 32
Cavity Cartridge
Fuse
Mini-
Fuse
Description
M18
—
15 Amp
Blue
Exterior Lighting –
Right Front Park and
Side Marker, Right
Tail and Running
Lights
M19
—
25 Amp
Natural
Automatic Shutdown
#1 and #2
M20
—
15 Amp
Blue
Interior Lighting/
Steering Wheel
Switches – If
Equipped/Switch
Bank/Steering Col-
umn Module – If
Equipped
M21
—
20 Amp
Yellow
Automatic Shutdown
#3
Cavity Cartridge
Fuse
Mini-
Fuse
Description
M22
—
10 Amp
Red
Right Horn (Hi/Low)
M23
—
10 Amp
Red
Left Horn (Hi/Low)
M24
—
25 Amp
Natural
Rear Wiper – If
Equipped
M25
—
20 Amp
Yellow
Fuel Pump, Diesel
Lift Pump – If
Equipped
M26
—
10 Amp
Red
Power Mirror Switch/
Driver Window
Switch
M27
—
10 Amp
Red
Ignition Switch/
Wireless Control
Module/Steering Col-
umn Lock – If
Equipped
496
MAINTAINING YOUR VEHICLE
Cavity Cartridge
Fuse
Mini-
Fuse
Description
M28
—
10 Amp
Red
Powertrain Control
Module
M29
—
10 Amp
Red
Occupant Classifica-
tion Module
M30
—
15 Amp
Blue
Rear Wiper Module –
If Equipped/Power
Folding Mirror – If
Equipped/Diagnostic
Link
M31
—
20 Amp
Yellow
Back-Up Lights
M32
—
10 Amp
Red
Airbag Module
M33
—
10 Amp
Red
Powertrain Control
Module
Cavity Cartridge
Fuse
Mini-
Fuse
Description
M34
—
10 Amp
Red
Park Assist Module –
If Equipped/Climate
Control System Mod-
ule – If Equipped/
Compass Module – If
Equipped/Cabin
Heater – If
Equipped/Diesel Rad
Fan – If Equipped
M35
—
15 Amp
Blue
Heated Mirrors – If
Equipped
M36
—
—
—
7
MAINTAINING YOUR VEHICLE
497
Cavity Cartridge
Fuse
Mini-
Fuse
Description
M37
—
10 Amp
Red
Antilock Brakes/
Stability Control Sys-
tem Module/Stop
Light Switch/Fuel
Pump Relay
M38
—
25 Amp
Natural
Door and Liftgate
Lock/Unlock Motors
CAUTION!
• When installing the Integrated Power Module
cover, it is important to ensure the cover is prop-
erly positioned and fully latched. Failure to do so
may allow water to get into the Integrated Power
Module, and possibly result in an electrical system
failure.
(Continued)
CAUTION! (Continued)
• When replacing a blown fuse, it is important to
use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated
may result in a dangerous electrical system over-
load. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be
corrected.
REPLACEMENT BULBS
LIGHT BULBS – Interior
Bulb No.
Cargo Lamp. . . . . . . . . . . . . . . . . . . . . . . . . TL212–2
Overhead Console Lamp . . . . . . . . . . . . . PLW214–2A
Reading Lamp . . . . . . . . . . . . . . . . . . . . . . WL212–2
498
MAINTAINING YOUR VEHICLE
LIGHT BULBS – Exterior
Bulb No.
Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 9008 H13
Front Park/Turn Signal Lamp. . . . . . . . . . . . . 3757AK
Front Side Marker Lamp . . . . . . . . . . . . . . . . . . . 168
Back-Up Lamp . . . . . . . . . . . . . . . . . . . . . . . . 3157K
Center High Mounted Stop Lamp (CHMSL) . . . . . LED
(serviced at an authorized dealer)
Fog Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . H10 9145
License Plate Lamp . . . . . . . . . . . . . . . . . . . . . . . 168
Rear Tail/Stop. . . . . . . . . . . . . . . . . . . . . . . . . 3157K
Rear Turn Signal Lamp . . . . . . . . . . . . . . . . . 3757AK
BULB REPLACEMENT
Headlamp
1. Open the hood.
2. Reach behind the headlamp housing to access the
headlamp bulb lock ring.
3. Firmly grasp the lock ring and rotate it counterclock-
wise to unlock it.
4. Remove the bulb and connector assembly from the
headlamp housing.
5. Disconnect the bulb from the electrical connector and
then connect the replacement bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
6. Install the bulb and connector assembly into the
headlamp housing and rotate the lock ring clockwise to
lock it in place.
7. Close the hood.
7
MAINTAINING YOUR VEHICLE
499
Front Turn Signal And Front Side Marker Lamp
1. Turn the steering wheel all the way to the right to
access the left front turn signal or side marker. Turn the
steering wheel all the way to the left to access the right
front turn signal or side marker.
2. Remove three push-pins from the wheel-well liner.
3. Gently flex the wheel-well liner forward to access the
bulb.
4. Rotate the bulb’s socket counterclockwise, and remove
the bulb and socket assembly from the housing.
5. Pull the bulb out of the socket and insert the replace-
ment bulb.
6. Install the bulb and socket assembly into the housing,
and rotate the socket clockwise to lock it in place.
7. Reposition the wheel-well liner and install the
push-pins.
Front Fog Lamp
1. Open the hood.
2. Reach behind the headlamp housing to access the
bulb.
3. Rotate the bulb’s socket counterclockwise, and remove
the bulb and socket assembly from the fog lamp housing.
4. Pull the bulb out of the socket and insert the replace-
ment bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
500
MAINTAINING YOUR VEHICLE
5. Install the bulb and socket assembly into the into the
fog lamp housing, and rotate the connector clockwise to
lock it in place.
6. Close the hood.
Rear Tail/Stop, Turn Signal, And Back-Up Lamp
1. Open the liftgate.
2. Remove the screws that fasten the taillamp housing to
the vehicle.
3. Pull the taillamp housing straight back to separate it
from the vehicle.
4. Disconnect the electrical connector.
5. Remove the two screws that fasten the back plate to
the taillamp housing.
6. Separate the back plate from the taillamp housing.
7
MAINTAINING YOUR VEHICLE
501
7. Pull the appropriate bulb(s) out of the back plate and
insert the replacement bulb(s).
8. Install the back plate and screws into the taillamp
housing.
9. Connect the electrical connector.
10. Install the taillamp housing and screws.
11. Close the liftgate.
FLUID CAPACITIES
U.S.
Metric
Fuel (Approximate)
19.5 Gallons
73.8 Liters
Engine Oil with Filter
3.7 Liter Engine (SAE 5W-20, API Certified)
5 Quarts
4.7 Liters
Cooling System *
3.7 Liter Engine (MOPAR
威 Antifreeze/Engine Coolant 5
Year/100,000 Mile Formula or equivalent)
14 Quarts
13.3 Liters
* Includes heater and coolant recovery bottle filled to MAX level.
502
MAINTAINING YOUR VEHICLE
FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine
Component
Fluid, Lubricant, or Genuine Part
Engine Coolant
MOPAR
威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy-
brid Organic Additive Technology) or equivalent.
Engine Oil
Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of
Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for
correct SAE grade.
Engine Oil Filter
MOPAR
威 Engine Oil Filter or equivalent.
Spark Plugs
ZFR6F-11G (Gap 0.043 in [1.1 mm])
Fuel Selection
87 Octane
7
MAINTAINING YOUR VEHICLE
503
Chassis
Component
Fluid, Lubricant, or Genuine Part
Automatic Transmission
MOPAR
威 ATF+4威 Automatic Transmission Fluid or equivalent licensed
ATF+4
威 product.
Transfer Case
MOPAR
威 ATF+4威 Automatic Transmission Fluid or equivalent licensed
ATF+4
威 product.
Front Axle
SAE 80W-90 Multi-Purpose Type, GL-5 Gear Lubricant or equivalent.
Rear Axle
SAE 75W-90 Gear Lubricant or equivalent.
Brake Master Cylinder
MOPAR
威 DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE
J1703 brake fluid is not available, then DOT 4 is acceptable. Use only rec-
ommended brake fluids.
Power Steering Reservoir
MOPAR
威 Power Steering Fluid +4, MOPAR威 ATF+4威 Automatic Trans-
mission Fluid or equivalent licensed ATF+4
威 product.
504
MAINTAINING YOUR VEHICLE
MAINTENANCE SCHEDULES
CONTENTS
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 506
▫ Required Maintenance Intervals . . . . . . . . . . 508
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
MAINTENANCE SCHEDULE
The Scheduled Maintenance services listed in this
manual must be done at the times or mileages specified
to protect your vehicle warranty and ensure the best
vehicle performance and reliability. More frequent main-
tenance may be needed for vehicles in severe operating
conditions, such as dusty areas and very short trip
driving. Inspection and service should also be done
anytime a malfunction is suspected.
Your vehicle is equipped with an automatic oil change
indicator system. The oil change indicator system will
remind you that it is time to take your vehicle in for
scheduled maintenance.
On Electronic Vehicle Information Center (EVIC)
equipped vehicles, “Oil Change Required” will be dis-
played in the EVIC and a single chime will sound,
indicating that an oil change is necessary.
On Non-EVIC equipped vehicles, “Change Oil” will flash
in the instrument cluster odometer and a single chime
will sound, indicating that an oil change is necessary.
Based on engine operation conditions, the oil change
indicator message will illuminate. This means that ser-
vice is required for your vehicle. Operating conditions
such as frequent short-trips, trailer tow, extremely hot or
cold ambient temperatures, and E85 fuel usage will
influence when the “Change Oil” message is displayed.
Depending on operating conditions, the message may
appear as early as 3,500 miles (5 630 km) since last reset.
Have your vehicle serviced as soon as possible, within
the next 500 miles (805 km).
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
506
MAINTENANCE SCHEDULES
NOTE:
• The oil change indicator message will not monitor the
time since the last oil change. Change your vehicle’s
oil if it has been six months since your last oil change,
even if the oil change indicator message is NOT
illuminated.
• Change your engine oil more often if you drive your
vehicle off-road for an extended period of time.
• Under no circumstances should oil change intervals
exceed 8,000 miles (13 000 km) or six months, which-
ever comes first.
Your authorized dealer will reset the oil change indicator
message after completing the scheduled oil change. If a
scheduled oil change is performed by someone other
than your authorized dealer, the message can be reset by
referring to the steps described under “Electronic Vehicle
Information Center (EVIC)/Oil Change Required” in
“Understanding Your Instrument Panel” or under “In-
strument Cluster Description/Odometer/Trip Odom-
eter” in “Understanding Your Instrument Panel” for
further information.
At Each Stop For Fuel
• Check the engine oil level about five minutes after a
fully warmed engine is shut off. Checking the oil level
while the vehicle is on level ground will improve the
accuracy of the oil level reading. Add oil only when
the level is at or below the ADD or MIN mark.
• Check the windshield washer solvent and add if
required.
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
MAINTENANCE SCHEDULES
507
Once A Month
• Check tire pressure and look for unusual wear or
damage.
• Inspect the battery and clean and tighten the terminals
as required.
• Check the fluid levels of the coolant reservoir and the
brake master cylinder, add as needed.
• Check all lights and other electrical items for correct
operation.
At Each Oil Change
• Change the engine oil filter.
• Inspect the brake hoses and lines.
CAUTION!
• Failure to perform the required maintenance items
may result in damage to the vehicle.
• Proper operation of four-wheel drive vehicles de-
pends on tires of equal size, type and circumfer-
ence on each wheel. Any difference in tire size can
cause damage to the transfer case. Tire rotation
schedule should be followed to balance tire wear.
Required Maintenance Intervals
Refer to the Maintenance Schedules on the following
pages for the required maintenance intervals.
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
508
MAINTENANCE SCHEDULES
8,000 Miles (13,000 km) or
6 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil
filter.
❏ Rotate the tires, rotate at the first sign of
irregular wear, even if it occurs before
8,000 miles (13 000 km).
Odometer Reading
Date
Repair Order #
Dealer Code
Signature, Authorized Service Center
16,000 Miles (26,000 km) or 12 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
16,000 miles (26 000 km).
❏ Replace the air conditioning filter.
❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the
engine air cleaner filter; replace if necessary.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect exhaust system. Perform the first inspection at 16,000 miles (26 000 km) or
12 months.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
Odometer Reading
Date
Repair Order #
Dealer Code
Signature, Authorized Service Center
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
MAINTENANCE SCHEDULES
509
24,000 Miles (39,000 km) or
18 Months Maintenance
Service Schedule
❏ Change the engine oil and engine oil
filter.
❏ Rotate the tires, rotate at the first sign of
irregular wear, even if it occurs before
24,000 miles (39 000 km).
❏ Inspect the CV joints.
❏ Inspect exhaust system.
❏ Inspect the front and rear axle fluid,
change if using your vehicle for police,
taxi, fleet, off-road or frequent trailer
towing.
Odometer Reading
Date
Repair Order #
Dealer Code
Signature, Authorized Service Center
32,000 Miles (52,000 km) or 24 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
32,000 miles (52 000 km).
❏ Replace the air conditioning filter.
❏ Replace the engine air cleaner filter.
❏ Replace the spark plugs (3.7L Engine).
❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
❏ Inspect the transfer case fluid.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
Odometer Reading
Date
Repair Order #
Dealer Code
Signature, Authorized Service Center
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
510
MAINTENANCE SCHEDULES
40,000 Miles (65,000 km) or
30 Months Maintenance
Service Schedule
❏ Change the engine oil and engine oil
filter.
❏ Rotate the tires, rotate at the first sign of
irregular wear, even if it occurs before
40,000 miles (65 000 km).
Odometer Reading
Date
Repair Order #
Dealer Code
Signature, Authorized Service Center
48,000 Miles (78,000 km) or 36 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
48,000 miles (78 000 km).
❏ Replace the air conditioning filter.
❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the
engine air cleaner filter; replace if necessary.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect the CV joints.
❏ Inspect exhaust system.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet,
off-road or frequent trailer towing.
Odometer Reading
Date
Repair Order #
Dealer Code
Signature, Authorized Service Center
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
MAINTENANCE SCHEDULES
511
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст