Jeep Liberty KJ. Manual — part 184
•
When Monitored:
With the ignition on.
•
Set Condition:
The Occupant Restraint Controller (ORC) monitors the resistance of the Driver Squib 2 circuits. The ORC will
set this DTC if it detects an open or high resistance on the Driver Squib 2 circuits.
Possible Causes
DRIVER SQUIB 2 LINE 1 CIRCUIT OPEN
DRIVER SQUIB 2 LINE 2 CIRCUIT OPEN
CLOCKSPRING
DRIVER AIRBAG
ORC
Diagnostic Test
1.
DETERMINE ACTIVE OR STORED DTC
NOTE: Ensure that the battery is fully charged.
NOTE: The scan tool, SRS Airbag Load Tool MRL 8443, and DVOM are required to perform the following
test.
Turn the ignition on.
SELECT ACTIVE or STORED DTC:
ACTIVE DTC
Go To 2
STORED DTC
Go To 6
2.
CHECK FOR OPEN SQUIB CIRCUITS IN DRIVER AIRBAG
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the Driver Airbag Squib connectors.
WARNING: To avoid personal injury or death, do not place an
intact undeployed airbag face down on a hard surface, the airbag
will propel into the air if accidentally deployed.
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool and appropriate Jumper to the Driver Air-
bag Squib connectors.
WARNING: To avoid personal injury or death, turn the ignition on,
then reconnect the battery.
With the scan tool, read the active ORC DTCs.
Does the scan tool display: DRIVER SQUIB 2 CIRCUIT OPEN?
Yes
>> Go To 3
No
>> Replace the Driver Airbag in accordance with the Service
Information.
Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.
8O - 42
RESTRAINTS - ELECTRICAL DIAGNOSTICS
KJ
3.
CHECK CLOCKSPRING SQUIB CIRCUITS FOR AN OPEN
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the 8443 Load Tool and Jumper from the Driver Airbag
Squib connectors.
Disconnect the Clockspring connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool and appropriate Jumper to the Clockspring
connector.
WARNING: To avoid personal injury or death, turn the ignition on,
then reconnect the battery.
With the scan tool, read the active ORC DTCs.
Does the scan tool display: DRIVER SQUIB 2 CIRCUIT OPEN?
Yes
>> Go To 4
No
>> Replace the Clockspring in accordance with the Service
Information.
Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.
4.
CHECK DRIVER SQUIB 2 LINE 1 CIRCUIT FOR AN OPEN
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the 8443 Load Tool and Jumper from the Clockspring con-
nector.
Disconnect the ORC connectors.
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool ORC Adaptor to the ORC connector.
Measure the resistance of the Driver Squib 2 Line 1 circuit between the
Clockspring connector and the ORC Load Tool Adaptor.
Is the resistance below 1.0 ohm?
Yes
>> Go To 5
No
>> Repair the Driver Squib 2 Line 1 circuit for an open.
Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.
KJ
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 43
5.
CHECK DRIVER SQUIB 2 LINE 2 CIRCUIT FOR AN OPEN
Measure the resistance of the Driver Squib 2 Line 2 circuit between the
Clockspring connector and the ORC Load Tool Adaptor.
Is the resistance below 1.0 ohm?
Yes
>>
WARNING: If the Occupant Restraint Controller (ORC) is dropped
at any time, it must be replaced. Failure to take the proper precau-
tions can result in accidental airbag deployment and personal
injury or death.
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Replace the ORC in accordance with the Service Informa-
tion.
Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.
No
>> Repair the Driver Squib 2 Line 2 circuit for an open.
Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.
6.
CHECKING STORED OR INTERMITTENT CODES
NOTE: Diagnose and repair all active codes before diagnosing stored codes. Refer to the Table of Contents
in this Section for a complete list of airbag system diagnostic procedures.
With the scan tool, record and erase all Airbag System Module DTCs.
WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the related wiring and connectors for chafed, pierced,
pinched, and partially broken wires, and for broken, bent, pushed out, corroded, and contaminated terminals. Repair
as necessary.
Reconnect all disconnected components and harness connectors.
WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
With the scan tool, monitor for active codes while performing the following:
•
Wiggle the wiring harness and connectors of the related airbag circuit.
•
Rotate the steering wheel from stop to stop.
•
Continue the test until either a code becomes active or the problem area is isolated.
In the previous steps you have attempted to recreate the conditions responsible for setting the DTC in question /
causing the intermittent condition.
Are any ACTIVE DTCs present?
Yes
>> Select the appropriate diagnostic procedure from the Table of Contents in this section.
No
>> No problem found at this time. Erase all codes before returning the vehicle to the customer.
8O - 44
RESTRAINTS - ELECTRICAL DIAGNOSTICS
KJ
DRIVER SQUIB 2 CIRCUIT SHORT
For a complete wiring diagram Refer to Section 8W.
KJ
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 45
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст