Jeep Liberty KJ. Manual — part 708
4.
FUEL INJECTOR QUANTITY
Turn the ignition off.
With the scan tool, perform the Injector Quantity Test.
Is the Injector Quantity within specification for all cylinders?
Yes
>> Go To 5
No
>> Repair or replace as necessary in accordance with the Service Information.
Perform the ECM Verification Test Ver. 1 (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
5.
FUEL INJECTOR LEAKAGE
Turn the ignition off.
Perform the INJECTOR LEAKAGE TEST in accordance with the Service Information.
Were any problems found?
Yes
>> Repair or replace as necessary in accordance with the Service Information.
Perform the ECM Verification Test Ver. 1 (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
No
>> Test Complete.
9 - 890
ENGINE DIESEL DIAG
KJ
P0301-MISFIRE DETECTED CYLINDER #1
For a complete wiring diagram Refer to Section 8W
•
When Monitored:
With the engine running.
•
Set Condition:
The ECM detects multiple misfires from cylinder #1.
Possible Causes
ENGINE COMPRESSION
FUEL INJECTOR QUANTITY
FUEL SUPPLY CONTAMINATION
INJECTOR LEAKAGE
INTERMITTENT CONDITION
Diagnostic Test
1.
CHECK FOR ACTIVE DTC
NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions
under which the DTC was set. Some of these conditions are displayed on the scan tool at the same time the
DTC is displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may
assist when checking for an active DTC.
With the scan tool, erase ECM DTCs.
Test drive the vehicle and attempt to duplicate the problem.
With the scan tool, read ECM DTC’s.
Did this DTC set again?
Yes
>> Go To 2
No
>> Refer to the *CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
2.
FUEL CONTAMINATION
Refer to the Service Information and inspect the fuel supply for contamination.
Is the fuel contaminated?
Yes
>> Refer to the Service Information to remove and replace fuel throughout the fuel system.
Perform the ECM Verification Test Ver. 1 (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
No
>> Go To 3
3.
ENGINE COMPRESSION
Turn the ignition off.
With the scan tool, perform the Cylinder Compression Test.
Is the cylinder compression within specification for all cylinders?
Yes
>> Go To 4
No
>> Repair as necessary in accordance with the Service Information.
Perform the ECM Verification Test Ver. 1 (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
KJ
ENGINE DIESEL DIAG
9 - 891
4.
FUEL INJECTOR QUANTITY
Turn the ignition off.
With the scan tool, perform the Injector Quantity Test.
Is the Injector Quantity within specification for all cylinders?
Yes
>> Go To 5
No
>> Repair or replace as necessary in accordance with the Service Information.
Perform the ECM Verification Test Ver. 1 (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
5.
FUEL INJECTOR LEAKAGE
Turn the ignition off.
Perform the INJECTOR LEAKAGE TEST in accordance with the Service Information.
Were any problems found?
Yes
>> Repair or replace as necessary in accordance with the Service Information.
Perform the ECM Verification Test Ver. 1 (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
No
>> Test Complete.
9 - 892
ENGINE DIESEL DIAG
KJ
P0302-MISFIRE DETECTED CYLINDER #2
For a complete wiring diagram Refer to Section 8W
•
When Monitored:
With the engine running.
•
Set Condition:
The ECM detects multiple misfires from cylinder #2.
Possible Causes
ENGINE COMPRESSION
FUEL INJECTOR QUANTITY
FUEL SUPPLY CONTAMINATION
INJECTOR LEAKAGE
INTERMITTENT CONDITION
Diagnostic Test
1.
CHECK FOR ACTIVE DTC
NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions
under which the DTC was set. Some of these conditions are displayed on the scan tool at the same time the
DTC is displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may
assist when checking for an active DTC.
With the scan tool, erase ECM DTCs.
Test drive the vehicle and attempt to duplicate the problem.
With the scan tool, read ECM DTC’s.
Did this DTC set again?
Yes
>> Go To 2
No
>> Refer to the *CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
2.
FUEL CONTAMINATION
Refer to the Service Information and inspect the fuel supply for contamination.
Is the fuel contaminated?
Yes
>> Refer to the Service Information to remove and replace fuel throughout the fuel system.
Perform the ECM Verification Test Ver. 1 (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
No
>> Go To 3
3.
ENGINE COMPRESSION
Turn the ignition off.
With the scan tool, perform the Cylinder Compression Test.
Is the cylinder compression within specification for all cylinders?
Yes
>> Go To 4
No
>> Repair as necessary in accordance with the Service Information.
Perform the ECM Verification Test Ver. 1 (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).
KJ
ENGINE DIESEL DIAG
9 - 893
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст