Jeep Liberty KJ. Manual — part 1429
POWER AMP SHUTDOWN - BASE AUDIO SYSTEM
For a complete wiring diagram Refer to Section 8W
•
When Monitored:
Ignition in RUN and IOD fuse installed.
•
Set Condition:
The radio has sensed a short on the output for more than 10 seconds.
Possible Causes
LEFT I/P SPEAKER
LEFT FRONT DOOR SPEAKER
RIGHT I/P SPEAKER
RIGHT FRONT DOOR SPEAKER
LEFT REAR SPEAKER
RIGHT REAR SPEAKER
(+) CIRCUIT SHORTED TO GROUND
SPEAKER SECTION OF RADIO
(-) CIRCUIT SHORTED TO GROUND
SPEAKER (+) & (-) CIRCUITS SHORTED TOGETHER
Diagnostic Test
1.
DETERMINE FAULT
Turn the ignition on.
Turn the Radio on.
With the Scan Tool, erase the audio DTC’s.
Cycle the ignition switch from off to on and wait 10 seconds.
With the Scan Tool, read the audio DTC’s.
Does the Scan Tool display POWER AMP SHUTDOWN?
Yes
>> Go To 2
No
>> Refer to the wiring diagrams located in the service information to help isolate a possible intermittent
short.
Perform BODY VERIFICATION TEST - VER 1.
2.
LEFT I/P SPEAKER
Turn the ignition off.
Disconnect the Left I/P Speaker harness connector.
Turn the ignition on.
Turn the radio on.
With the Scan Tool, erase the audio DTCs.
Cycle the ignition switch from off to on and wait 10 seconds.
With the Scan Tool, read DTC’s.
Does the Scan Tool display POWER AMP SHUTDOWN?
Yes
>> Go To 3
No
>> Replace the Left I/P Speaker.
Perform BODY VERIFICATION TEST - VER 1.
8A - 20
AUDIO/VIDEO - ELECTRICAL DIAGNOSTICS
KJ
3.
LEFT FRONT DOOR SPEAKER
Turn the ignition off.
Disconnect the Left Front Door Speaker harness connector.
Turn the ignition on.
Turn the radio on.
With the Scan Tool, erase the audio DTCs.
Cycle the ignition switch from off to on and wait 10 seconds.
With the Scan Tool, read DTC’s.
Does the Scan Tool display POWER AMP SHUTDOWN?
Yes
>> Go To 4
No
>> Replace the Left Front Door Speaker.
Perform BODY VERIFICATION TEST - VER 1.
4.
RIGHT I/P SPEAKER
Turn the ignition off.
Disconnect the Right I/P Speaker harness connector.
Turn the ignition on.
Turn the radio on.
With the Scan Tool, erase the audio DTCs.
Cycle the ignition switch from off to on and wait 10 seconds.
With the Scan Tool, read DTC’s.
Does the Scan Tool display POWER AMP SHUTDOWN?
Yes
>> Go To 5
No
>> Replace the Right I/P Speaker.
Perform BODY VERIFICATION TEST - VER 1.
5.
RIGHT FRONT DOOR SPEAKER
Turn the ignition off.
Disconnect the Right Front Door Speaker harness connector.
Turn the ignition on.
Turn the radio on.
With the Scan Tool, erase the audio DTCs.
Cycle the ignition switch from off to on and wait 10 seconds.
With the Scan Tool, read DTC’s.
Does the Scan Tool display POWER AMP SHUTDOWN?
Yes
>> Go To 6
No
>> Replace the Right Front Door Speaker.
Perform BODY VERIFICATION TEST - VER 1.
KJ
AUDIO/VIDEO - ELECTRICAL DIAGNOSTICS
8A - 21
6.
LEFT REAR SPEAKER
Turn the ignition off.
Disconnect the Left Rear Speaker harness connector.
Turn the ignition on.
Turn the radio on.
With the Scan Tool, erase the audio DTCs.
Cycle the ignition switch from off to on and wait 10 seconds.
With the Scan Tool, read DTC’s.
Does the Scan Tool display POWER AMP SHUTDOWN?
Yes
>> Go To 7
No
>> Replace the Left Rear Speaker.
Perform BODY VERIFICATION TEST - VER 1.
7.
RIGHT REAR SPEAKER
Turn the ignition off.
Disconnect the Right Rear Speaker harness connector.
Turn the ignition on.
Turn the radio on.
With the Scan Tool, erase the audio DTCs.
Cycle the ignition switch from off to on and wait 10 seconds.
With the Scan Tool, read DTC’s.
Does the Scan Tool display POWER AMP SHUTDOWN?
Yes
>> Go To 8
No
>> Replace the Right Rear Speaker.
Perform BODY VERIFICATION TEST - VER 1.
8.
(+) CIRCUIT SHORTED TO GROUND
Turn the ignition off.
Disconnect the Left Front Door Speaker harness connector.
Disconnect the Left I/P Speaker harness connector.
Disconnect the Right Front Door Speaker harness connector.
Disconnect the Right I/P Speaker harness connector.
Disconnect the Left Rear Speaker harness connector.
Disconnect the Right Rear Speaker harness connector.
Disconnect the Radio C1 harness connector.
Measure the resistance between ground and each speaker (+) circuit.
Is the resistance below 1000.0 (1K) ohms?
Yes
>> Repair the speaker (+) circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
>> Go To 9
8A - 22
AUDIO/VIDEO - ELECTRICAL DIAGNOSTICS
KJ
9.
(-) CIRCUIT SHORTED TO GROUND
Turn the ignition off.
Disconnect the Left Front Door Speaker harness connector.
Disconnect the Left I/P Speaker harness connector.
Disconnect the Right Front Door Speaker harness connector.
Disconnect the Right I/P Speaker harness connector.
Disconnect the Left Rear Speaker harness connector.
Disconnect the Right Rear Speaker harness connector.
Disconnect the Radio C1 harness connector.
Measure the resistance between ground and each speaker (-) circuit.
Is the resistance below 1000.0 (1K) ohms?
Yes
>> Repair the speaker (-) circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
>> Go To 10
10.
SPEAKER (+) & (-) CIRCUITS SHORTED TOGETHER
Turn the ignition off.
Disconnect the Left Front Door Speaker harness connector.
Disconnect the Left I/P Speaker harness connector.
Disconnect the Right Front Door Speaker harness connector.
Disconnect the Right I/P Speaker harness connector.
Disconnect the Left Rear Speaker harness connector.
Disconnect the Right Rear Speaker harness connector.
Disconnect the Radio C1 harness connector.
Measure the resistance between each speaker (+) circuit and each speaker (-) circuit.
Is the resistance below 1000.0 (1K) ohms for any of the measurements?
Yes
>> Repair the shorted together speaker circuits.
Perform BODY VERIFICATION TEST - VER 1.
No
>> Go To 11
11.
SPEAKER SECTION OF RADIO
If there are no possible causes remaining, view repair.
Repair
Replace the Radio.
Perform BODY VERIFICATION TEST - VER 1.
KJ
AUDIO/VIDEO - ELECTRICAL DIAGNOSTICS
8A - 23
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст