Jeep Liberty KJ. Manual — part 485
P0123-THROTTLE POSITION SENSOR 1 CIRCUIT HIGH
For a complete wiring diagram Refer to Section 8W.
9 - 98
ENGINE ELECTRICAL DIAGNOSTICS
KJ
•
When Monitored:
With the ignition on. Battery voltage greater than 10.4 volts.
•
Set Condition:
Throttle Position Sensor voltage at the PCM is greater than 4.47 volts for 1.3 seconds. One Trip Fault. Three
good trips to turn off the MIL.
Possible Causes
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT OPEN
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO THE (F855) 5-VOLT SUPPLY CIRCUIT
(K900) SENSOR GROUND CIRCUIT OPEN
THROTTLE POSITION SENSOR
PCM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).
Diagnostic Test
1.
TP SENSOR VOLTAGE ABOVE 4.5 VOLTS
NOTE: Make sure the throttle is fully closed and free from binding and carbon build up.
Start the engine.
With a scan tool, read the TP Sensor voltage.
Is the voltage above 4.5 volts?
Yes
>> Go To 2
No
>> Go To 8
2.
THROTTLE POSITION SENSOR
Turn the ignition off.
Disconnect the TP Sensor harness connector.
Connect a jumper wire between the (K22) TP Sensor No.1 Signal circuit
and the (K900) Sensor ground circuit in the Sensor harness connector.
With a scan tool, monitor the TP Sensor voltage.
Ignition on, engine not running.
Is the voltage below 0.5 of a volt with the jumper wire
installed?
Yes
>> Replace the Throttle Position Sensor.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 3
NOTE: Remove the jumper wire before continuing.
KJ
ENGINE ELECTRICAL DIAGNOSTICS
9 - 99
3.
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
Turn the ignition off.
Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (K22) TP Sensor No.1 Signal circuit in the
TP Sensor harness connector.
Is the voltage above 5.2 volts?
Yes
>> Repair the short to battery voltage in the (K22) TP Sensor
No.1 Signal circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 4
4.
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT OPEN
Turn the ignition off.
CAUTION: Do not probe the PCM harness connectors. Probing the
PCM harness connectors will damage the PCM terminals resulting
in poor terminal to pin connection. Install Miller Special Tool #8815
to perform diagnosis.
Measure the resistance of the (K22) TP Sensor No.1 Signal circuit from
the TP Sensor harness connector to the appropriate terminal of special
tool #8815.
Is the resistance below 5.0 ohms?
Yes
>> Go To 5
No
>> Repair the open in the (K22) TP Sensor No.1 Signal circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
9 - 100
ENGINE ELECTRICAL DIAGNOSTICS
KJ
5.
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO THE (F855) 5-VOLT SUPPLY CIRCUIT
Measure the resistance between the (K22) TP Sensor No.1 Signal cir-
cuit and the (F855) 5-volt Supply circuit in the TP Sensor harness con-
nector.
Is the resistance below 100 ohms?
Yes
>> Repair the short between the (F855) 5-volt Supply circuit
and the (K22) TP Sensor No.1 Signal circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 6
6.
(K900) SENSOR GROUND CIRCUIT OPEN
Measure the resistance of the (K900) Sensor ground circuit from the TP
Sensor harness connector to the appropriate terminal of special tool
#8815.
Is the resistance below 5.0 ohms?
Yes
>> Go To 7
No
>> Repair the open in the (K900) Sensor ground circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
7.
PCM
NOTE: Before continuing, check the PCM harness connector terminals for corrosion, damage, or terminal
push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay particular attention to all Power and
Ground circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Replace and program the Powertrain Control Module per Service Information.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
KJ
ENGINE ELECTRICAL DIAGNOSTICS
9 - 101
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст