Jeep Liberty KJ. Manual — part 106
1. Vehicles for all markets except Japan should have
the headlamp low beams selected with the dimmer
(multi-function) switch during the adjustment proce-
dure. Vehicles for the Japanese market should
have the headlamp high beams selected.
2. Cover the lens of the headlamp that is not being
adjusted.
3. Turn the adjusting screw (3) until the top edge of
the beam intensity pattern is positioned from just
below horizontal to 75 millimeters (3 inches) below
the headlamp horizontal centerline for vehicles in
North America, or from just below horizontal to 125
millimeters (5 inches) below the headlamp horizon-
tal centerline for Export vehicles.
4. Repeat the adjustment procedure for the opposite
headlamp.
8L - 82
LAMPS/LIGHTING - EXTERIOR
KJ
LICENSE PLATE LAMP
REMOVAL
BULB - NORTH AMERICA
1. Disconnect and isolate the battery negative cable.
2. Reach through the opening in the rear bumper fas-
cia (1) between the license plate and the lamp (2)
to access the socket (3) on the back of the license
plate lamp unit housing.
3. Firmly grasp and pull the socket and bulb (4)
straight out of the opening in the back of the
license plate lamp housing.
4. Pull the bulb straight out of the socket.
BULB - EXPORT
1. Disconnect and isolate the battery negative cable.
2. Unsnap and lift up the bottom of the license mount-
ing plate far enough to access and remove the two
screws (4) that secure the license plate bracket (3)
to the special lug nuts (2) on the spare tire (1).
3. Swing the license plate bracket (2) away from the
spare tire far enough to access the license plate
lamp bulb sockets (4).
4. Firmly grasp the socket on the top of the license
plate lamp unit housing for the bulb that is being
removed.
5. Rotate
the
socket
counterclockwise
about
30
degrees to unlock it.
6. Pull the socket and bulb straight out from the
keyed opening in the top of the lamp housing.
7. Pull the base of the bulb straight out of the socket.
KJ
LAMPS/LIGHTING - EXTERIOR
8L - 83
LAMP - NORTH AMERICA
1. Disconnect and isolate the battery negative cable.
2. Remove the two screws (3) that secure the license
plate lamp unit (2) to the rear bumper fascia (1).
3. Lower the lamp from the mounting hole in the fas-
cia far enough to access and disconnect the lamp
pigtail wire connector.
4. Remove the license plate lamp unit from the
vehicle.
LAMP - EXPORT
1. Disconnect and isolate the battery negative cable.
2. Remove the bulb and socket (4) from the license
plate lamp unit (1) that is being removed. (Refer to
8 - ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/
LICENSE PLATE LAMP BULB - REMOVAL -
EXPORT).
3. Remove the two screws (3) that secure the lamp
unit to the back of the license plate bracket (2).
4. Remove the lamp unit from the back of the license
plate bracket.
INSTALLATION
BULB - NORTH AMERICA
CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may
overheat and cause damage to the lamp, the socket and/or the lamp wiring.
8L - 84
LAMPS/LIGHTING - EXTERIOR
KJ
1. Align the base of the bulb (4) with the license plate
lamp socket (3).
2. Push the bulb straight into the socket until the base
is firmly seated.
3. Reach through the opening in the rear bumper fas-
cia (1) between the license plate and the lamp (2)
to align the socket and bulb with the opening on
the back of the lamp housing.
4. Insert the socket and bulb straight into the housing
until the socket is firmly seated.
5. Reconnect the battery negative cable.
BULB - EXPORT
CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may
overheat and cause damage to the lamp, the socket and/or the lamp wiring.
1. Align the base of the bulb with the license plate
lamp socket (4).
2. Push the bulb straight into the socket until the base
is firmly seated.
3. Align the socket and bulb with the keyed opening
on the top of the license plate lamp unit (1).
4. Insert the socket and bulb into the housing until the
socket is firmly seated.
5. Rotate the socket clockwise about 30 degrees to
lock it into place.
6. Swing the license plate bracket (3) back against
the spare tire (1).
7. Lift up the bottom of the license mounting plate far
enough to install and tighten the two screws (4)
that secure the license plate bracket to the special
lug nuts (2) on the spare tire. Tighten the screws to
28 N·m (21 ft. lbs.).
8. Lower the bottom of the license mounting plate and
snap it into place on the license plate bracket.
9. Reconnect the battery negative cable.
KJ
LAMPS/LIGHTING - EXTERIOR
8L - 85
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст