Jeep Liberty KJ. Manual — part 274
the hood is closed. As the plunger is depressed, the plunger stop contacts the top of the sleeve and the sleeve is
driven downward, ratcheting through the switch mounting collar until the hood is fully closed and latched. The ribs
on the sleeve are engaged within the mounting collar to maintain this adjusted position.
The hood ajar switch and circuits may be diagnosed using conventional diagnostic tools and methods. Refer to the
appropriate wiring information. However, conventional diagnostic methods may not prove conclusive in the diagnosis
of the BCM or its responses to the hood ajar switch input. The most reliable, efficient, and accurate means to diag-
nose the hood ajar switch, the BCM, and both the hard wired and electronic message inputs and outputs affected
by the hood ajar switch input requires the use of a diagnostic scan tool. Refer to the appropriate diagnostic infor-
mation.
REMOVAL
SWITCH
1. Unlatch and open the hood.
2. Disconnect and isolate the battery negative cable.
3. From the top of the mounting bracket (3) on the
right front fender inner shield (1), squeeze the two
hood ajar switch (4) latch tabs together and pull the
switch upward.
4. Pull the hood ajar switch up through the hole in the
mounting bracket far enough to access and discon-
nect the wire harness connector (5) from the switch
connector receptacle.
5. Remove the hood ajar switch from the mounting
bracket.
8Q - 72
VEHICLE THEFT SECURITY - SERVICE INFORMATION
KJ
BRACKET
1. Remove the hood ajar switch (4) from the mounting
bracket (3). (Refer to 8 - ELECTRICAL/VEHICLE
THEFT
SECURITY/HOOD
AJAR
SWITCH
-
REMOVAL).
2. If necessary, remove and set aside the engine air
cleaner housing for access to the hood ajar switch
mounting bracket screws (2).
3. Remove the two screws that secure the hood ajar
switch bracket to the right fender inner shield (1).
4. Remove the hood ajar switch bracket from the right
fender inner shield.
STRIKER
NOTE: The hood ajar switch striker is not intended for reuse. If the striker is removed from the hood inner
reinforcement for any reason, it must be replaced.
1. Unlatch and open the hood (3).
2. Using a trim stick or another suitable wide flat-
bladed tool, pry the rearward end of the hood ajar
switch striker (1) away from the inner hood panel
reinforcement far enough to disengage the integral
retainer (4) from its mounting hole.
3. Move the hood ajar switch striker slightly rearward
to disengage the integral mounting tab (2) from the
forward mounting hole.
4. Remove the hood ajar switch striker from the inner
hood panel reinforcement and discard.
KJ
VEHICLE THEFT SECURITY - SERVICE INFORMATION
8Q - 73
INSTALLATION
SWITCH
1. Position the hood ajar switch (4) near the hole in
the mounting bracket (3) on the right inner fender
side shield (1).
2. Pull the wire harness connector (5) through the
switch mounting bracket and reconnect it to the
switch connector receptacle.
3. From the top of the mounting bracket, press the
switch downward into the mounting hole until the
integral switch latch tabs lock it into place.
4. Reconnect the battery negative cable.
5. Close and latch the hood.
BRACKET
1. Position the hood ajar switch bracket (3) onto the
right fender inner shield (1).
2. Install and tighten the two screws (2) that secure
the hood ajar switch bracket to the right fender
inner shield. Tighten the screws to 7 N·m (60 in.
lbs.).
3. If removed, reinstall the engine air cleaner housing.
4. Reinstall the hood ajar switch (4) into the mounting
bracket. (Refer to 8 - ELECTRICAL/VEHICLE
THEFT
SECURITY/HOOD
AJAR
SWITCH
-
INSTALLATION).
STRIKER
NOTE: The hood ajar switch striker is not intended for reuse. If the striker is removed from the hood inner
reinforcement for any reason, it must be replaced.
8Q - 74
VEHICLE THEFT SECURITY - SERVICE INFORMATION
KJ
1. Position the new hood ajar switch striker (1) to the
inner hood panel reinforcement (3).
2. Insert the mounting tab (2) on the front of the hood
ajar switch striker into the forward mounting hole.
3. Align the retainer (4) on the rear of the hood ajar
switch striker with the rearward mounting hole.
4. Using hand pressure, press the hood ajar switch
striker rearward and upward against the inner hood
panel reinforcement until the retainer is fully
engaged in the rearward mounting hole.
5. Close and latch the hood.
KJ
VEHICLE THEFT SECURITY - SERVICE INFORMATION
8Q - 75
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст