Jeep Liberty KJ. Manual — part 19
CLEVIS BRACKET
REMOVAL
1. Raise and support the vehicle.
2. Remove the tire and wheel assembly.
3. Remove the lower clevis bolt (3) at the lower con-
trol arm.
4. Remove the upper clevis bolt (1) at the shock.
5. Remove the lower stabilizer link bolt at the lower
control arm.
6. Remove the lower ball joint nut.
7. Separate the lower ball joint from the lower control
arm using remover C-4150A.
8. Swing the lower control arm downward to allow
clearance to remove the clevis bracket (2).
9. Remove the clevis bracket (2) from the vehicle.
INSTALLATION
1. Install the clevis bracket (2) upper bolt (1) to the
shock Seat the clevis against the stop on the
shock. Tighten the bolt (1) to 61 N·m (45 ft.lbs.).
2. Raise the lower control arm to the lower ball joint.
3. Install the nut to the lower ball joint. Tighten the nut
to 81 N·m (60 ft.lbs.).
4. Install the clevis bracket (2) lower bolt (3) to the
lower control arm. Tighten the bolt (3) to 150 N·m
(110 ft.lbs.).
5. Install the lower stabilizer link bolt at the lower con-
trol arm. Tighten the bolt to 115 N·m (85 ft.lbs.).
6. Install the tire and wheel assembly. (Refer to 22 -
TIRES/WHEELS/WHEELS - STANDARD PROCE-
DURE).
7. Lower the vehicle.
2 - 26
FRONT
KJ
STABILIZER BAR
REMOVAL
1. Raise and support the vehicle.
2. Remove the tire and wheel assembly.
3. Remove the upper stabilizer link bolts at the stabi-
lizer bar (1).
4. Remove the stabilizer bar bushing clamps (2) from
the frame.
5. Remove the stabilizer bar (1) from the vehicle.
INSTALLATION
1. Install the stabilizer bar (1) to the vehicle.
2. Install the stabilizer bar bushing clamps (2). Tighten
the nuts to 149 N·m (110 ft.lbs.).
3. Install the upper stabilizer link bolts and washer at
the stabilizer bar (1). Tighten the bolt to 136 N·m
(100 ft.lbs.).
4. Install the tire and wheel assembly. (Refer to 22 -
TIRES/WHEELS/WHEELS - STANDARD PROCE-
DURE).
5. Lower the vehicle.
KJ
FRONT
2 - 27
STABILIZER LINK
REMOVAL
1. Raise and support the vehicle.
2. Remove the tire and wheel assembly.
3. Remove the lower stabilizer link bolt (2) at the
lower control arm.
4. Remove the upper stabilizer link bolt (2) at the sta-
bilizer bar (1).
5. Remove the stabilizer link (2).
INSTALLATION
1. Install the stabilizer link (2).
2. Install the upper stabilizer link bolt (2) and washer
at the stabilizer bar. Tighten the bolt to 136 N·m
(100 ft.lbs.).
3. Install the lower stabilizer link bolt (2) and washer
at the lower control arm. Tighten the nut to 115
N·m (85 ft.lbs.).
4. Install the tire and wheel assembly. (Refer to 22 -
TIRES/WHEELS/WHEELS
-
STANDARD
PROCEDURE).
2 - 28
FRONT
KJ
UPPER CONTROL ARM
REMOVAL
RIGHT SIDE
1. Raise and support the vehicle.
2. Remove the right side tire and wheel assembly.
3. Remove the upper ball joint nut.
4. Separate the upper ball joint from the steering knuckle using remover C-4150A.
5. Lower the vehicle.
6. Remove the air box (Refer to 9 - ENGINE/AIR INTAKE SYSTEM/AIR CLEANER ELEMENT - REMOVAL).
7. Remove the cruise control servo mounting nuts.
8. Remove the upper control arm rear bolt.
9. Remove the upper control arm front bolt.
10. Remove the upper control arm from the vehicle.
LEFT SIDE
1. Raise and support the vehicle.
2. Remove the left side tire and wheel assembly.
3. Remove the upper ball joint nut.
4. Separate the upper ball joint from the steering knuckle using remover C-4150A.
5. Lower the vehicle.
6. Remove the battery (Refer to 8 - ELECTRICAL/BATTERY SYSTEM/BATTERY - REMOVAL).
7. Unclip the power center and move it to the side out of the way.
8. Remove the battery tray (Refer to 8 - ELECTRICAL/BATTERY SYSTEM/TRAY - REMOVAL).
9. Disconnect the battery temperature sensor from the battery tray.
10. Remove the upper control arm rear bolt (2) by
using a ratchet and extension (3) under the steer-
ing shaft (1) and positioned by the power steering
reservoir.
11. Remove the upper control arm front bolt.
12. Remove the upper control arm from the vehicle.
INSTALLATION
RIGHT SIDE
1. Install the upper control arm to the vehicle.
2. Install the upper control arm front bolt. Tighten the bolt to 122 N·m (90 ft.lbs.).
3. Install the upper control arm rear bolt. Tighten the bolt to 122 N·m (90 ft.lbs.).
4. Install the cruise control servo mounting nuts.
KJ
FRONT
2 - 29
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст