Jeep Liberty KJ. Manual — part 15
FRONT
TABLE OF CONTENTS
page
page
FRONT
TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
FRONT SUSPENSION . . . . . . . . . . . . . . . . . . . . . . . 13
BUSHINGS
HUB / BEARING
KNUCKLE
LOWER BALL JOINT
DIAGNOSIS AND TESTING - LOWER BALL
JOINT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LOWER CONTROL ARM
SHOCK
SPRING
CLEVIS BRACKET
STABILIZER BAR
STABILIZER LINK
UPPER CONTROL ARM
2 - 10
FRONT
KJ
FRONT
DESCRIPTION
NOTE: Suspension components with rubber/ure-
thane bushings (2) should be tightened with the
vehicle at normal ride height. It is important to
have the springs supporting the weight of the
vehicle when the fasteners are torqued. If springs
are not at their normal ride position, vehicle ride
comfort could be affected and premature bushing
wear may occur.
The front suspension is designed to allow each wheel
to adapt to different road surfaces independently. The
wheels are mounted to hub bearings on the steering
knuckle spindles (5). The double-row hub bearings are
sealed and lubricated for life. The steering knuckles
turn (pivot) on ball joints integral to the outboard por-
tion of the upper control arms and pressed into the
lower steering knuckle. The ball joints are lubricated for life.
WARNING
WARNING: Suspension components with rubber bushings must be tightened with the vehicle at normal ride
height. It is important to have the springs supporting the weight of the vehicle when the fasteners are
torqued. If springs are not at their normal ride position, vehicle ride comfort will be affected and cause
premature bushing wear.
SPECIFICATIONS
TORQUE
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Front Shock Absorber
Clevis Bracket Upper Nut
61
45
—
Front Shock Absorber
Clevis Bracket Lower Nut
150
110
—
Front Shock Absorber Top
(4) Mounting Nuts
108
80
—
Front Shock to Spring and
Insulator Nut
41
30
—
Upper Suspension Arm
Front Nut
122
90
—
Upper Suspension Arm
Rear Nut
122
90
—
Lower Suspension Arm
Front Nut
170
125
—
Lower Suspension Arm
Rear Nut
170
125
—
Stabilizer Bar Clamp Nut
149
110
—
Stabilizer Bar Link Upper
Nut
136
100
—
KJ
FRONT
2 - 11
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Stabilizer Bar Link Lower
Nut
115
85
—
Hub/Bearing
Bolt
130
96
—
Hub/Bearing
Halfshaft Nut
135
100
—
Upper Ball Joint Nut
81
60
—
Lower Ball Joint Nut
81
60
—
Wheel Speed Sensor
13.5
10
—
2 - 12
FRONT
KJ
SPECIAL TOOLS
FRONT SUSPENSION
BALL JOINT PRESS - C-4212F
Remover C-4150A
REMOVER / INSTALLER FRONT LOWER BALL
JOINT - 8859
FRONT LOWER CONTROL ARM & CLEVIS BUSHING
REMOVER/INSTALLER - 8858
FRONT LOWER CONTROL BUSHING REMOVER/
INSTALLER - 8830
RECEIVER CUP - 6761
KJ
FRONT
2 - 13
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст