Jeep Liberty KJ. Manual — part 633
4.
CHECK FOR ADDITIONAL COMMUNICATION RELATED DTCS
With the scan tool, select Network View and select Advanced.
Is there more than one module with active DTCs “Logged Against” the BCM?
Yes
>> Replace/update the BCM in accordance with the service information.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).
No
>> Replace the PCM in accordance with the service information.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).
9 - 590
ENGINE ELECTRICAL DIAGNOSTICS
KJ
U0155-LOST COMMUNICATION WITH CLUSTER
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on
•
Battery voltage between 10 and 16 volts
•
IOD fuse installed
•
Set Condition:
If the PCM fails to receive bus messages from the Cluster for approximately 500 ms.
Possible Causes
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
CAN C BUS CIRCUITS OPEN OR SHORTED
CLUSTER POWER AND GROUND
CLUSTER
PCM
Diagnostic Test
1.
VERIFY DTC IS ACTIVE
NOTE: Ensure the IOD fuse is installed and battery voltage is between 10 and 16 volts before proceeding.
Turn the ignition on.
With the scan tool, read active DTCs.
Is this DTC active?
Yes
>> Go To 2
No
>> Perform the Stored Lost Communication test procedure. (Refer to 8 - ELECTRICAL/ELECTRONIC
CONTROL MODULES - DIAGNOSIS AND TESTING).
2.
CHECK FOR ANY OF THE FOLLOWING ACTIVE DTCS
With the scan tool, read all active DTCs from all CAN C Bus modules.
NOTE: Check for CAN C hardware electrical, VIN Missing/Mismatch, battery or ignition related DTCs.
Does the scan tool display any active DTCs to the conditions listed above?
Yes
>> Diagnose and repair the DTC(s). Refer to the Table of Contents in the applicable Section.
No
>> Go To 3
3.
VERIFY THAT THE CLUSTER IS ACTIVE ON THE BUS
With the scan tool, select ECU View.
Verify that the Cluster is active on the bus.
Is the Cluster active on the bus?
Yes
>> Go To 4
No
>> (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for No
Response related diagnostic procedures.
KJ
ENGINE ELECTRICAL DIAGNOSTICS
9 - 591
4.
CHECK FOR ADDITIONAL COMMUNICATION RELATED DTCS
With the scan tool, select Network View and select Advanced.
Is there more than one module with active DTCs “Logged Against” the CLUSTER?
Yes
>> Replace/update the Cluster in accordance with the service information.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).
No
>> Replace the PCM in accordance with the service information.
Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).
9 - 592
ENGINE ELECTRICAL DIAGNOSTICS
KJ
U0168-LOST COMMUNICATION WITH SKIM/SKREEM (WCM)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on
•
Battery voltage between 10 and 16 volts
•
IOD fuse installed
•
Set Condition:
If the PCM fails to receive bus messages from the SKREEM (WCM) for approximately 500 ms.
Possible Causes
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
CAN C BUS CIRCUITS OPEN OR SHORTED
SKREEM (WCM) POWER AND GROUND
SKREEM (WCM)
PCM
Diagnostic Test
1.
VERIFY DTC IS ACTIVE
NOTE: Ensure the IOD fuse is installed and battery voltage is between 10 and 16 volts before proceeding.
Turn the ignition on.
With the scan tool, read active DTCs.
Is this DTC active?
Yes
>> Go To 2
No
>> Perform the Stored Lost Communication test procedure. (Refer to 8 - ELECTRICAL/ELECTRONIC
CONTROL MODULES - DIAGNOSIS AND TESTING).
2.
CHECK FOR ANY OF THE FOLLOWING ACTIVE DTCS
With the scan tool, read all active DTCs from all CAN C Bus modules.
NOTE: Check for CAN C hardware electrical, VIN Missing/Mismatch, battery or ignition related DTCs.
Does the scan tool display any active DTCs to the conditions listed above?
Yes
>> Diagnose and repair the DTC(s). Refer to the Table of Contents in the applicable Section.
No
>> Go To 3
3.
VERIFY THAT THE SKREEM (WCM) IS ACTIVE ON THE BUS
With the scan tool, select ECU View.
Verify that the SKREEM (WCM) is active on the bus.
Is the SKREEM (WCM) active on the bus?
Yes
>> Go To 4
No
>> (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for No
Response related diagnostic procedures.
KJ
ENGINE ELECTRICAL DIAGNOSTICS
9 - 593
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст