Jeep Liberty KJ. Manual — part 983
LINKAGE
TABLE OF CONTENTS
page
page
TIE ROD END
LINKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
19 - 32
LINKAGE
KJ
TIE ROD END
STANDARD PROCEDURE - STEERING LINKAGE
The tie rod end and ball stud seals should be inspected during all oil changes. If a seal is damaged, replace the tie
rod.
CAUTION: If any steering components are replaced or serviced an alignment must be performed, to ensure
the vehicle meets all alignment specifications.
REMOVAL
1. Raise and support the vehicle.
2. Remove the tire and wheel assembly.
NOTE: Mark the tie rod end jam nuts on the steer-
ing gear for easier installation.
3. Loosen the tie rod end jam nut (1).
4. Remove the outer tie rod end (3) nut.
5. Separate the outer tie rod end (3) from the knuckle
using tool C3894A.
NOTE: Count the number of turns when removing.
6. Remove the outer tie rod end (3) from the inner tie
rod (2).
INSTALLATION
1. Install the outer tie rod end (3) to the inner tie rod
end (2) to the exact number of turns that it was
removed.
2. Install the outer tie rod end (3) to the knuckle.
Tighten the nut to 108 N·m (80 ft.lbs).
3. Tighten the jam nut to 75 N·m (55 ft.lbs).
4. Install the tire and wheel assembly. (Refer to 22 -
TIRES/WHEELS/WHEELS - STANDARD PROCE-
DURE).
5. Reset the toe and center the steering wheel (Refer
to 2 - SUSPENSION/WHEEL ALIGNMENT - STAN-
DARD PROCEDURE).
KJ
LINKAGE
19 - 33
PUMP
TABLE OF CONTENTS
page
page
PUMP
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
STANDARD PROCEDURE
OPERATION - GAS ENGINE. . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . 36
TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
POWER STEERING PUMP . . . . . . . . . . . . . . . . . . 41
FLUID
STEERING FLUID LEVEL CHECKING . . . . . . . . . 42
FLUID COOLER
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
HOSES
COOLER). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
PRESSURE / RETURN HOSE ASSEMBLY -
DIESEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
COOLER). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
PRESSURE / RETURN HOSE ASSEMBLY -
DIESEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
PULLEY
RESERVOIR
19 - 34
PUMP
KJ
PUMP
DESCRIPTION
DIESEL POWER STEERING PUMP
Hydraulic pressure for the power steering system is
provided by a belt driven power steering pump (3).
The pump shaft has a bolt-on drive pulley that is belt
driven by the crankshaft pulley. The reservoir is sep-
erate from the pump body (3). The power steering
pump is connected to the steering gear by the pres-
sure and return hoses.
3.7L POWER STEERING PUMP
Hydraulic pressure for the power steering system is
provided by a belt driven power steering pump (4).
The pump shaft has a pressed-on high strength plastic
drive pulley (3) that is belt driven by the crankshaft
pulley. The integral reservoir (1) used on the 3.7L is
attached to the pump body (4) with spring clips (5).
OPERATION
The power steering pump is a constant flow rate and displacement, vane-type pump. The pump internal parts oper-
ate submerged in fluid. The flow control orifice is part of the high pressure line fitting. The pressure relief valve
inside the flow control valve limits the pump pressure.
NOTE: Power steering pumps have different pressure rates and are not interchangeable with other pumps.
STANDARD PROCEDURE
POWER STEERING PUMP - INITIAL OPERATION - GAS ENGINE
WARNING: The fluid level should be checked with engine off to prevent injury from moving components.
KJ
PUMP
19 - 35
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст