Jeep Liberty KJ. Manual — part 114
REAR LAMP UNIT
REMOVAL
BULB
NOTE: The rear lamp unit may contain up to four bulbs, depending upon the market for which the vehicle
was manufactured. The service procedures for each bulb are the same, only the bulb sizes and types may
differ.
1. Disconnect and isolate the battery negative cable.
2. Remove the rear lamp unit (1) from the end of the
quarter panel. (Refer to 8 - ELECTRICAL/LAMPS/
LIGHTING
-
EXTERIOR/REAR
LAMP UNIT -
REMOVAL).
3. Firmly grasp the socket (2) on the socket plate (4)
on the back of the rear lamp unit housing for the
bulb that is being removed and rotate it counter-
clockwise about 30 degrees to unlock it.
4. Pull the socket and bulb (3) straight out of the
keyed opening in the socket plate.
5. Pull the base of the bulb straight out of the rear
lamp socket.
LAMP
1. Disconnect and isolate the battery negative cable.
2. Open the tailgate to access and remove the two
screws (5) that secure the rear lamp unit (4) to the
two plastic nuts (1) in the side jamb of the tailgate
opening.
3. Pull the outboard side of the rear lamp unit rear-
ward far enough to unsnap the two ball studs on
the outboard side of the lamp housing from the two
plastic grommets (3) in the quarter panel.
4. Disconnect the wire harness connector (2) from the
lamp socket plate connector.
5. Remove the lamp from the quarter panel.
6. Remove the two plastic grommets from the quarter
panel and discard.
INSTALLATION
BULB
CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may
overheat and cause damage to the lamp, the socket and/or the lamp wiring.
NOTE: The rear lamp unit may contain up to four bulbs, depending upon the market for which the vehicle
was manufactured. The service procedures for each bulb are the same, only the bulb sizes and types may
differ.
8L - 114
LAMPS/LIGHTING - EXTERIOR
KJ
1. Align the base of the bulb (3) with the rear lamp
socket (2).
2. Push the bulb straight into the socket until the base
is firmly seated.
3. Align the socket and bulb with the keyed opening
in the socket plate (4) on the back of the rear lamp
unit housing (1).
4. Insert the socket and bulb straight into the socket
plate until the socket is firmly seated.
5. Rotate the socket clockwise about 30 degrees to
lock it into place.
6. Reinstall the rear lamp unit onto the end of the
quarter panel. (Refer to 8 - ELECTRICAL/LAMPS/
LIGHTING
-
EXTERIOR/REAR
LAMP UNIT -
INSTALLATION).
7. Reconnect the battery negative cable.
LAMP
1. Install two new plastic grommets (3) into the quar-
ter panel.
2. Position the rear lamp unit (4) to the quarter panel.
3. Reconnect the wire harness connector (2) to the
lamp socket plate connector.
4. Align the two ball studs on the outboard side of the
rear lamp housing with the two plastic grommets in
the quarter panel.
5. Using hand pressure, push firmly and evenly on
the outboard side of the lamp until the two ball
studs snap into the plastic grommets.
6. Install and tighten the two screws (5) that secure
the inboard side of the lamp housing to the plastic
nuts (1) in the side jamb of the tailgate opening.
Tighten the screws to 2 N·m (20 in. lbs.).
7. Reconnect the battery negative cable.
KJ
LAMPS/LIGHTING - EXTERIOR
8L - 115
REPEATER LAMP
REMOVAL
BULB
NOTE: Side repeater lamps are used only on vehicles manufactured for certain markets where these lamps
are required.
1. Disconnect and isolate the battery negative cable.
2. Remove the repeater lamp unit from the front
fender panel (1). (Refer to 8 - ELECTRICAL/
LAMPS/LIGHTING - EXTERIOR/REPEATER LAMP
UNIT - REMOVAL).
3. Rotate the repeater lamp socket (2) in the lamp
lens (4) counterclockwise about 30 degrees to
unlock it.
4. Pull the socket and bulb (3) straight out of the
keyed opening in the lamp lens.
5. Pull the base of the bulb straight out of the lamp
socket.
LAMP
NOTE: Side repeater lamps are used only on vehicles manufactured for certain markets where these lamps
are required.
1. Disconnect and isolate the battery negative cable.
2. Using a trim stick or another suitable wide flat-
bladed tool, carefully pry at the clearance notch in
the lower edge of the repeater lamp lens (1) to dis-
engage the snap features of the lens from the
mounting hole in the front fender panel (2).
3. Pull the lamp unit out from the front fender panel
far enough to access and disconnect the wire har-
ness connector from the lamp socket.
4. Remove the lamp unit from the front fender panel.
INSTALLATION
BULB
CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may
overheat and cause damage to the lamp, the socket and/or the lamp wiring.
NOTE: Side repeater lamps are used only on vehicles manufactured for certain markets where these lamps
are required.
8L - 116
LAMPS/LIGHTING - EXTERIOR
KJ
1. Align the base of the bulb (3) with the repeater
lamp socket (2).
2. Push the bulb straight into the socket until the base
is firmly seated.
3. Align the socket and bulb with the keyed opening
on the back of the repeater lamp lens (4).
4. Insert the socket and bulb straight into the lens
until the socket is firmly seated
5. Rotate the socket clockwise in the lens about 30
degrees to lock it into place.
6. Reinstall the repeater lamp unit onto the front
fender panel (1). (Refer to 8 - ELECTRICAL/
LAMPS/LIGHTING - EXTERIOR/REPEATER LAMP
UNIT - INSTALLATION).
7. Reconnect the battery negative cable.
LAMP
NOTE: Side repeater lamps are used only on vehicles manufactured for certain markets where these lamps
are required.
1. Position the repeater lamp unit (1) to the front
fender panel (2).
2. Reconnect the wire harness connector to the lamp
socket.
3. Position the lamp unit into the mounting hole in the
front fender panel. Be certain that the clearance
notch on the edge of the lamp lens is oriented
towards the bottom.
4. Using hand pressure, press on the lamp lens firmly
and evenly until the snap features of the lamp are
fully engaged in the mounting hole of the front
fender panel.
5. Reconnect the battery negative cable.
KJ
LAMPS/LIGHTING - EXTERIOR
8L - 117
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст