Jeep Renegade (2018 year). Instruction — part 16
IMPORTANT Do not operate the rear
window wiper with the blade lifted
from the rear window.
Windscreen washer
The windscreen jets, located on the
bonnet, are fixed.
If there is no jet of fluid, firstly check
that there is fluid in the reservoir (see
paragraph “Engine compartment” in this
chapter). Then check that the nozzle
holes are not clogged; use a needle to
unblock them if necessary.
IMPORTANT In versions with a sun
roof, make sure that the sun roof is
closed before operating the window
washer jets.
Rear window washer
The rear window washer jets are fixed.
The nozzle holder is located above the
rear window.
WARNING
189) The air intake system (air cleaner,
rubber hoses, etc.) can be a protection in
the case of blowbacks from the engine.
DO NOT REMOVE this system unless you
need to carry out repair or servicing
operations. Before starting the engine,
ensure that the system has not been
removed: failure to observe this precaution
may result in serious injury.
190) Exhaust emissions are very
dangerous, and may be lethal. They
contain carbon monoxide, a colourless,
odourless gas which can cause fainting
and poisoning if inhaled.
191) The exhaust system may reach high
temperatures and may cause a fire if the
vehicle is parked on flammable material.
Dry grass or leaves can also catch fire if
they come into contact with the exhaust
system. Do not park or use the vehicle in a
place in which the exhaust system might
come into contact with flammable
material.
IMPORTANT
89) Incorrect servicing of the vehicle or
failure to carry out operations or repairs
(when necessary) may lead to more
expensive repairs, damage to other
components or have a negative impact on
the vehicle performance. Have any
malfunction inspected immediately by a
Jeep Dealership.
90) The vehicle is equipped with fluids
which are optimised or protecting its
performance and life and extending
service intervals. Do not use chemicals for
washing these components since they may
damage the engine, the gearbox or the
climate control system. This damage is not
covered by the vehicle’s warranty. If any
component needs to be washed due to
malfunctioning, use only the specific
liquid for that procedure.
91) An excessive or insufficient amount of
oil inside the base is extremely damaging
to the engine. Make sure it is always at an
adequate level.
205
J0A0346C
253
92) Always require the use of only
compressor coolants and lubricants
approved and suitable for the specific air
conditioning system fitted on the vehicle.
Some non-approved coolants are
flammable and may explode, with the risk
of injuries. The use of non-approved
coolants or lubricants may adversely affect
system efficiency, leading to expensive
repairs.
93) The air conditioner system contains
coolant under high pressure: to avoid
injuries to people or damage to the
system, any coolant addition or repair that
requires to disconnect the cables must be
carried out by a Jeep Dealership.
94) Vehicles equipped with catalytic
converter must be fuelled only with
unleaded petrol. Leaded petrol would
permanently damage the catalytic
converter and eliminate its ability to
reduce polluting emissions, seriously
compromising the engine performance,
which would be irreparably damaged. If
the engine does not work correctly,
especially if it starts irregularly or if there
is a reduction of its performance,
immediately go to a Jeep Dealership.
Prolonged and faulty operation of the
engine may cause overheating of the
converter and, as a consequence, possible
damage to the converter and the vehicle.
95) Using a gearbox fluid different from
that approved may compromise
gearshifting quality and/or cause vibration
of the gearbox itself.
96) It is recommended to have the vehicle
serviced by a Jeep Dealership. When
carrying out normal periodic operations
and small servicing interventions
personally on the vehicle, it is
recommended to use suitable equipment,
genuine spare parts and the necessary
fluids. Do not carry out any interventions if
you don't have the necessary experience.
LIFTING THE VEHICLE
If the vehicle is to be lifted, go to a Jeep
Dealership which is equipped with the
arm lift or workshop lift.
254
SER
VICING
AND
MAINTENANCE
WHEELS AND TYRES
SUGGESTIONS ABOUT THE
ROTATION OF THE TYRES
192) 193)
97) 98) 99) 100)
The front and rear tyres are subject to
different loads and stress due to steering,
manoeuvres and braking. For this reason
they are subject to uneven wear.
To resolve this problem, tyres should be
rotated at the appropriate time. This
operation is recommended for tyres with
a deep tread pattern, suitable both for
on-road and off-road driving.
Tyre rotation contributes to the
preservation of the grip and traction
performance on wet, muddy or snowy
roads, guaranteeing optimal driveability
of the vehicle.
In the case of irregular wear of the tyres,
the reason must be identified and
corrected before rotating them.
WARNING
192) Do not cross switch the tyres if they
are "unidirectional" type. In this case,
always take care not to fit the tyres with a
direction of rotation that is opposite to
that indicated: you would risk losing grip
and control of the vehicle.
193) Travelling with partially or completely
deflated tyres can cause safety problems
and damage the concerned tyre beyond
repair.
IMPORTANT
97) The road holding qualities of the car
also depend on the correct inflation
pressure of the tyres.
98) If tyre pressure is too low, the tyre may
overheat and be severely damaged as a
result.
99) Do not switch tyres from the
right-hand side of the vehicle to the
left-hand side, and vice versa.
100) Never submit alloy rims to repainting
treatments requiring the use of
temperatures exceeding 150°C. The
mechanical properties of the wheels could
be impaired.
SNOW CHAINS
101)
Front-wheel drive and four-wheel drive
versions: 7-mm snow chains can be used
on 215/65 R16 and 215/60 R17 tyres.
Chains cannot be fitted on
225/55 R18 tyres. e di incidenti.
IMPORTANT Use snow chains in
accordance with local regulations of each
country. In certain countries, tyres
marked with code M+S (Mud and Snow)
are considered as winter equipment;
therefore their use is equivalent to that of
the snow chains.
The snow chains may be applied only to
the front wheel tyres.
Check the tension of the snow chains
after the first few metres have been
driven.
Using snow chains with tyres with
non-original dimensions may damage the
vehicle.
Using different size or type (M+S, snow,
etc.) tyres between front and rear axle
may adversely affect vehicle driveability,
255
with the risk of losing control of the
vehicle and causing accidents.
IMPORTANT
101) Keep the vehicle's speed down when
snow chains are fitted; never exceed
50 km/h. Avoid potholes, do not drive over
steps or pavements and do not drive long
distances over roads without snow, to
avoid damaging both your vehicle and the
road surface.
BODYWORK
PRESERVING THE BODYWORK
Paintwork
102)
7)
Touch up abrasions and scratches
immediately to prevent the formation of
rust.
Versions with matt paint
(where provided)
Some parts of the vehicle are painted
with a matte paintwork which requires
special care for its preservation
103)
Washing the car
To correctly wash the car, follow these
instructions:
if the vehicle is washed remove the
aerial from the roof;
Versions with stickers (where
provided): avoid washing with rollers
and/or brushes in washing stations. Wash
the car by hand only, using pH-neutral
detergents Dry it with a damp chamois
leather. Abrasive products and/or
polishes should not be used for cleaning
the car.
if high pressure jets or cleaners are
used to wash the vehicle, keep a
distance of at least 40 cm from the
bodywork to avoid damage or alteration.
Build up of water could cause damage to
the car in the long term;
wash the bodywork using a low
pressure jet of water;
wipe a sponge with a slightly soapy
solution over the bodywork, frequently
rinsing the sponge;
rinse well with water and dry with a jet
of air or a chamois leather.
IMPORTANT
102) In order to preserve the aesthetic
appearance of the paint abrasive products
and/or polishes should not be used for
cleaning the vehicle.
256
SER
VICING
AND
MAINTENANCE
103) Avoid washing with rollers and/or
brushes in washing stations. Wash the
vehicle only by hand using neutral pH
detergents; dry it with a wet chamois
leather. Abrasive products and/or polishes
should not be used for cleaning the car.
Bird droppings must be washed off
immediately and thoroughly as the acid
they contain is particularly aggressive.
Avoid (if at all possible) parking the
vehicle under trees; remove vegetable
resins immediately as, when dried, it may
only be possible to remove them with
abrasive products and/or polishes, which is
highly inadvisable as they could alter the
typical opaqueness of the paint. Do not
use pure windscreen washer fluid for
cleaning the front windscreen and rear
window; dilute it min. 50% with water.
Only use pure screen washer fluid when
strictly necessary due to outside
temperature conditions.
IMPORTANT
7) Detergents pollute the environment.
Only wash your vehicle in areas equipped
to collect and treat wastewater from this
type of activity.
257
TECHNICAL DATA
Everything you may find useful for
understanding how your vehicle is made
and works is contained in this chapter
and illustrated with data, tables and
graphics. For the enthusiasts and the
technician, but also just for those who
want to know every detail of their vehicle.
IDENTIFICATION DATA . . . . . . . . .260
ENGINE . . . . . . . . . . . . . . . . . .261
WHEELS. . . . . . . . . . . . . . . . . .265
DIMENSIONS. . . . . . . . . . . . . . .269
WEIGHTS . . . . . . . . . . . . . . . . .273
SUPPLIES. . . . . . . . . . . . . . . . .279
FLUIDS AND LUBRICANTS . . . . . .283
PERFORMANCE . . . . . . . . . . . . .287
FUEL CONSUMPTION . . . . . . . . .288
CO2 EMISSIONS. . . . . . . . . . . . .290
PRESCRIPTIONS FOR HANDLING THE
VEHICLE AT THE END OF ITS LIFE .292
259
IDENTIFICATION DATA
VEHICLE IDENTIFICATION
NUMBER
The Vehicle Identification Number (VIN)
is stamped on a plate on the front left
corner of the dashboard cover fig. 206,
which can be seen from outside the
vehicle, through the windscreen.
This number is also stamped on the
passenger compartment floor, next to the
front right seat.
Slide flap A fig. 207, operating as shown
in the figure, to access.
VIN PLATE
The plate is located on the left side front
door pillar fig. 208 and shows the data
about:
A: correct value of smoke coefficient
(for Diesel engines);
B: name of the manufacturer, vehicle
type-approval number, vehicle
identification number, max. permitted
weights;
C: engine identification, type variant
version, spare part number, colour code,
additional information.
206
J0A0030C
207
J0A0028C
208
J0A0446C
260
TECHNICAL
DA
T
A
ENGINE
Versions
1.4 T-jet 120 HP
Petrol/LPG
1.4 Turbo Multi Air
136/140/170 OHP
1.6 E.Torq
2.4 Tigershark
(*)
Engine code
55277701
55263624
55263623
(**)
55263842
–
Cycle
Otto
Otto
Otto
Otto
Number and position of cylinders
4 in line
4 in line
4 in line
4 in line
Piston bore and stroke (mm)
72.0 × 84.0
72.0 × 84.0
77 × 85.8
88.0 × 97.0
Total displacement (cm³)
1368
1368
1598
2360
Compression ratio
9.8 ± 0.2
10 : 1
11 : 1
10 : 1
Maximum power (EC) (kW)
88
100
(*)
/ 103
/ 125
(**)
81
129
Maximum power (EEC) (HP)
120
136
(*)
/ 140
/ 170
(**)
110
175
corresponding engine speed (rpm)
5000
5000
/ 5500
(**)
5500
6400
(*) Where fitted
(**) 1.4 Turbo MultiAir 170 HP version
261
Versions
1.4 T-jet 120 HP
Petrol/LPG
1.4 Turbo Multi Air
136/140/170 OHP
1.6 E.Torq
2.4 Tigershark
(*)
Maximum torque (EEC) (Nm)
215
230
/ 250
(**)
152
230
Maximum torque (EEC) (kgm)
22
23.5
/ 25.5
(**)
15.5
23.4
corresponding engine speed (rpm)
2500
1750
/ 2500
(**)
4500
3900
Spark plugs
NGK IKR9J8
NGK IKR9J8
NGK - SINGLE IR -
ZKR7BI -
10 JAPAN C128
Fuel
Automotive LPG
(Specification
EN589) (LPG fuel
supply)/Green
unleaded petrol
95 R.O.N.
(Specification
EN228) (petrol
fuel supply)
Unleaded petrol
95 R.O.N.
(EN228 specifications)
Unleaded petrol
95 R.O.N.
(EN228 specifications)
Unleaded petrol
95 R.O.N.
(EN228 specifications)
(*) Where fitted
(**) 1.4 Turbo MultiAir 170 HP version
262
TECHNICAL
DA
T
A
Versions
1.6 16V MultiJet 95 HP
1.6 16V MultiJet 105 HP
1.6 16V Multijet
115/120 HP
(*)
Engine code
55260384
55260384
55260384
Cycle
Diesel
Diesel
Diesel
Number and position of cylinders
4 in line
4 in line
4 in line
Piston bore and stroke (mm)
79.5 × 80.5
79.5 × 80.5
79.5 × 80.5
Total displacement (cm³)
1598
1598
1598
Compression ratio
16.5 : 1
16.5 : 1
16.5 : 1
Maximum power (EC) (kW)
70
77
85
/ 88
Maximum power (EEC) (HP)
95
105
115
/ 120
corresponding engine speed (rpm)
4000
4500
3750
Maximum torque (EEC) (Nm)
320
320
320
Maximum torque (EEC) (kgm)
32.6
32.6
32.6
corresponding engine speed (rpm)
1750
1750
1750
Fuel
Diesel for motor vehicles
(EN590 Specification)
Diesel for motor vehicles
(EN590 Specification)
Diesel for motor vehicles
(EN590 Specification)
(*) Where fitted
263
Versions
2.0 16V Multijet 120 HP
2.0 16V Multijet 140 HP
2.0 16V Multijet 170 HP
Engine code
55263087
55263087 / 55263088
(*)
55263088
Cycle
Diesel
Diesel
Diesel
Number and position of cylinders
4 in line
4 in line
4 in line
Piston bore and stroke (mm)
83 × 90.4
83 × 90.4
83 × 90.4
Total displacement (cm³)
1956
1956
1956
Compression ratio
16.5
16.5
16.5
Maximum power (EC) (kW)
88
103
125
Maximum power (EEC) (HP)
120
140
170
corresponding engine speed (rpm)
4000
3750 / 4000
(*)
3750
Maximum torque (EC) (Nm)
320
350
350
Maximum torque (EC) (kgm)
32.6
35.7
35.7
corresponding engine speed (rpm)
1250
1500 / 1750
(*)
1750
Fuel
Diesel for motor vehicles
(EN590 Specification)
Diesel for motor vehicles
(EN590 Specification)
Diesel for motor vehicles
(EN590 Specification)
(*) Versions with automatic transmission
264
TECHNICAL
DA
T
A
WHEELS
RIMS AND TYRES
Alloy or pressed steel rims. Tubeless
radial carcass tyres.
All approved tyres are listed in the
Registration Document.
IMPORTANT If there are any
discrepancies between the “Owner
Handbook” and the “Registration
Document”, take the information from
the latter. For safe driving, the car
must be fitted with tyres of the same
make and type on all wheels.
IMPORTANT Do not use air chambers
with tubeless tyres.
SPACE SAVER SPARE WHEEL
(where provided)
Tyre: T145/90 R16 106M
Rim: 4.0 B x 16H ET22
WARNING
194) If winter tyres with a lower speed
rating than that indicated in the
Registration Document are used, do not
exceed the maximum speed corresponding
to the speed rating of the tyres used.
195) DO NOT fit wheel hub caps when
using integral hub caps fixed (with
springs) to the steel rim and after sale
tyres provided with Rim Protector. Use of
unsuitable tyres and wheel caps may
cause sudden decrease of tyre pressure.
265
RIMS AND TYRES PROVIDED
194) 195)
Versions
Wheels
Tyres
Snow tyres
1.4 T-Jet 120 HP LPG
6.5J x 16 ET40
215/65 R16 98H
215/65 R16 98Q (M+S)
7J x 17 ET40
215/60 R17 96H
215/60 R17 96Q (M+S)
1.4 Turbo Multi Air
6.5J x 16 ET40
215/65 R16 98H
215/65 R16 98Q (M+S)
7J x 17 ET40
215/60 R17 96H
215/60 R17 96Q (M+S)
7J x 18 ET 40
225/55 R18 98V
225/55 R18 98Q (M+S)
1.6 E.Torq
6.5J x 16 ET40
215/65 R16 98H
215/65 R16 98Q (M+S)
7J x 17 ET40
215/60 R17 96H
215/60 R17 96Q (M+S)
7J x 18 ET 40
225/55 R18 98V
225/55 R18 98Q (M+S)
2.4 Tigershark
(*)
6.5J x 16 ET40
215/65 R16 98H
215/65 R16 98Q (M+S)
6.5J x 17 ET40
(**)
215/60 R17 96H (M+S)
(**)
215/60 R17 96Q (M+S)
7J x 17 ET40
215/60 R17 96H
215/60 R17 96Q (M+S)
7J x 18 ET 40
225/55 R18 98V
225/55 R18 98Q (M+S)
(*) Where fitted
(**) Trailhawk versions
266
TECHNICAL
DA
T
A
Versions
Wheels
Tyres
Snow tyres
1.6 16V MultiJet
6.5J x 16 ET40
215/65 R16 98H
215/65 R16 98Q (M+S)
7J x 17 ET40
215/60 R17 96H
215/60 R17 96Q (M+S)
7J x 18 ET 40
225/55 R18 98V
225/55 R18 98Q (M+S)
2.0 16V MultiJet
6.5J x 16 ET40
215/65 R16 98H
215/65 R16 98Q (M+S)
6.5J x 17 ET40
(**)
215/60 R17 96H (M+S)
(**)
215/60 R17 96Q (M+S)
(**)
7J x 17 ET40
215/60 R17 96H
215/60 R17 96Q (M+S)
7J x 18 ET 40
225/55 R18 98V
225/55 R18 98Q (M+S)
(**) Trailhawk versions
267
COLD TYRE INFLATION PRESSURE
When the tires are warm, the inflation pressure should be + 0.3 bar in relation to the recommended figure. However, recheck that
the value is correct with the tyre cold. With snow tyres, add +0.2 bar to the pressure value prescribed for standard tyres.
Tyres
Unladen/medium load
Full load
Full size spare
wheel
(*)
Space saver
spare wheel
Front
Rear
Front
Rear
215/65 R16 98H
2.4
2.2
2.4
2.4
2.4
4.2
215/60 R17 96H
2.4
2.2
2.4
2.4
225/55 R18 98V
2.4
2.2
2.4
2.4
(*) After using the spare wheel in an emergency, where necessary, align the pressure of the wheel to the recommended value as soon as
possible, with reference to the following table.
268
TECHNICAL
DA
T
A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст