Engine Iveco Vector 8. Manual — part 28
!
Handle all parts extremely carefully.
Never get your hands or fingers between pieces.
Wear the required safety clothing such as goggles,
gloves, safety shoes and helmet.
Every 25,000 km check the level of oil in the sump with the
dipstick.
The level must be between the max and min marks on the
dipstick.
If necessary, top up with oil of the same type contained in the
sump via the filler (Urania Turbo type of oil)
When filling, it is recommended to take out the
dipstick to help the oil flow into the sump.
!
Handle all parts extremely carefully.
Never get your hands or fingers between pieces.
Wear the required safety clothing such as goggles,
gloves, safety shoes and helmet.
Before touching the filters, make sure the engine
temperature is not such as to cause burns.
Engine lubricating oil is harmful: avoid contact with
skin and eyes. In the event of contact, wash with
plenty of running water.
To change the engine oil filters, proceed as illustrated here.
Before removing the filters, place a tray of
sufficient capacity in a suitable position: each filter
contains approximately 1 kg of engine oil.
Figure 1
To remove the engine oil filters (2) use tool 99368538 (1).
NOTE
CHECKING/REFILLING ENGINE OIL
FILTERS
CHANGING ENGINE OIL FILTERS
83512
NOTE
84
SECTION 3 - INDUSTRIAL APPLICATION
VECTOR 8 ENGINES
Base - April 2006
Print P2D32V001E
Replace the filters with new parts, lubricate the seals slightly
with engine oil, hand screw and tighten for another 3/4 turn
(tighten whit tool 99368539).
Improper waste disposal is a threat for the
environment. Potentially hazardous waste used on
IVECO vehicles includes lubricants, fuels, coolants,
filters and batteries.
—
Use watertight containers when draining off
fluids. Never use containers for foodstuffs or
beverages that can lead people to drink from
them.
—
Never throw waste on the ground, on tips or
in water courses.
—
Obtain information on the appropriate ways
of recycling or disposing of waste from the
local authorities or collection centres.
Use only genuine products, capable of extending
the efficiency and life of the engine.
After fitting the filters, check the sump oil level and turn the
engine for a little while.
Stop the engine, wait for roughly ten minutes and check the
oil level again.
Top up as necessary.
Figure 2
NOTE
103184
SECTION 3 - INDUSTRIAL APPLICATION
85
VECTOR 8 ENGINES
Print P2D32V001E
Base - April 2006
- If not done beforehand, change the oil filters.
- Start up the engine, checking there is no leakage or
seepage.
The engine lubricating oil must be changed every 100000 km
according to the directions illustrated here.
Before draining off the oil, place a tray of sufficient
capacity under the oil sump in correspondence
with the drain plug. Quantity of oil contained in
sump approximately 40 litres.
- Unscrew the plug on the filler and extract the dipstick.
- Unscrew the oil drain plug and insert the drain tool
99368537.
- Drain the oil from the sump.
- Extract the drain tool 99368537 and screw on the plug.
- Add clean oil, checking the level from time to time by
inserting the dipstick. Quantity of oil approximately 40
litres.
- Put the plug on the filler.
Improper waste disposal is a threat for the
environment. Potentially hazardous waste used on
IVECO vehicles includes lubricants, fuels, coolants,
filters and batteries.
—
Use watertight containers when draining off
fluids. Never use containers for foodstuffs or
beverages that can lead people to drink from
them.
—
Never throw waste on the ground, on tips or
in water courses.
—
Obtain information on the appropriate ways
of recycling or disposing of waste from the
local authorities or collection centres.
!
Handle all parts extremely carefully. Never get your
hands or fingers between pieces. Wear the required
safety clothing such as goggles, gloves, safety shoes
and helmet.
Before touching the sump plug, check that the
temperature of the oil in the engine is not such as
to cause burns.
Engine lubricating oil is harmful: avoid contact with
skin and eyes. In the event of contact, wash with
plenty of running water.
CHANGING THE ENGINE OIL
NOTE
86
SECTION 3 - INDUSTRIAL APPLICATION
VECTOR 8 ENGINES
Base - April 2006
Print P2D32V001E
Figure 3
Figure 4
Figure 5
- Remove the connector (3) for indicating water in the
fuel filter by acting on the locking piston (4).
- Turn the screw (1) and separate the connecting head (2)
from the filter casing (3).
- If the condensate drain operation is carried out, retighten
the screw plug as soon as the fuel begins to emerge.
- If you need to change the filter, fully drain the diesel in
the filter cartridge and separate component (2) from
filter cartridge (3).
- After positioning the tool 99360076 under the filter,
unscrew and remove the filter (1) with the aid of a 27
mm wrench (2).
CHANGING FUEL PREFILTER AND
WATER SEPARATOR FILTER
!
Handle all parts extremely carefully.
Never get your hands or fingers between pieces.
Wear the required safety clothing such as goggles,
gloves, safety shoes and helmet.
To change the fuel pre—filter and water separator filter,
proceed as illustrated here.
Before disassembling, place under the filter a basin
of suitable capacity.
Improper waste disposal is a threat for the
environment. Potentially hazardous waste used on
IVECO vehicles includes lubricants, fuels, coolants,
filters and batteries.
—
Use watertight containers when draining off
fluids. Never use containers for foodstuffs or
beverages that can lead people to drink from
them.
—
Never throw waste on the ground, on tips or
in water courses.
—
Obtain information on the appropriate ways
of recycling or disposing of waste from the
local authorities or collection centres.
Hand screw and tighten for another 3/4 turn.
83486
NOTE
83488
83487
SECTION 3 - INDUSTRIAL APPLICATION
87
VECTOR 8 ENGINES
Print P2D32V001E
Base - April 2006
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст