Iveco Stralis AT/AD. Manual — part 225
Figure 67
38697
73838
Figure 68
Removal
Take out the nuts or screws (
⇒) fixing the longitudinal (2,
Figure 68) or triangular (1, Figures 48-49) suspension arms
and remove them.
Refitting
For refitting, carry out the steps described for removal in re-
verse order, tightening the nuts or screws to the required tor-
que.
LONGITUDINAL AND TRIANGULAR SUSPENSION ARMS FITTED ON 6x2 P VEHICLES
TRIANGULAR SUSPENSION ARM FITTED
ON 6x2 C VEHICLES
2
1
68
SUSPENSIONS
S
TRALIS
AT/AD
Base - January 2003
REMOVING-REFITTING THE REAR AXLE LONGITUDINAL SUSPENSION ARM
528914
REMOVING-REFITTING THE REAR ADDED AXLE LONGITUDINAL
SUSPENSION ARM
528918
REMOVING-REFITTING THE REAR AXLE TRIANGULAR SUSPENSION ARM
528919
REMOVING-REFITTING THE REAR ADDED AXLE TRIANGULAR
SUSPENSION ARM
38700
79479
Figure 69
Figure 70
LONGITUDINAL SUSPENSION ARM
TRIANGULAR SUSPENSION ARM
Removal
Using a suitable press and drift, compress the flexible part of the pin (1) in order to remove the circlip (2) and the underlying ring
(3) with pincers.
Withdraw the pin (1) from the suspension arm (4).
Refitting
Carry out the removal operations in reverse order, bearing in mind that the pin mounting face must be positioned at 90_ to the
longitudinal axis of the suspension arm. The circlip opening must be oriented as shown in the detail in the figure.
SUSPENSIONS
69
S
TRALIS
AT/AD
REPLACING THE SUSPENSION ARM FLEXIBLE PIN
38694
73701
Figure 71
Figure 72
Remove the stabilizer bar by removing the nuts or
screws securing the fixing pins and the cap retaining
bolts.
ASSEMBLY DRAWING FOR FRONT STABILIZER BAR
1. Upper hanger bracket - 2. Link rod - 3. Stabilizer bar - 4. Rubber bushing (in two halves) - 5. Front axle - 6. Cap.
ASSEMBLY DRAWING FOR FRONT STABILIZER BAR: 4x2 — 6x2P VEHICLES
WITH AIR SUSPENSION AND LONGITUDINAL BARS
1. Link rod - 2. Upper hanger bracket - 3. Stabilizer bar - 4. Rubber bushing (in two halves) - 5. Front axle - 6. Cap.
Check the bushings and/or rubber mountings and
renew them if they show signs of wear or
deterioration.
Refitting
Refit by carrying out the removal operations in reverse
order; tighten nuts/bolts to the specified torques.
!
Position the half bushings (4) so that the joint is
located as shown in the figure.
Removal
70
SUSPENSIONS
S
TRALIS
AT/AD
Base - January 2003
STABILIZER BAR
528930
FRONT STABILIZER BAR
528940
CENTRAL ADDED AXLE STABILIZER BAR (6x2 C vehicles)
528960
REAR STABILIZER BAR
528970
REAR ADDED AXLE STABILIZER BAR (6x2P vehicles)
72238
72237
38695
Figure 73
Figure 74
Figure 75
ASSEMBLY DRAWING FOR REAR STABILIZER BAR: 4x2 — 6x2C — 6x4 VEHICLES
1. Upper hanger bracket - 2. Link rod - 3. Stabilizer bar - 4. Rubber bushing (in two halves) - 5. Rear axle - 6. Cap.
ASSEMBLY DRAWING FOR REAR AXLE ANTI-ROLL BAR: 6x2 VEHICLES
1. Upper hanger bracket - 2. Link rod - 3. Anti-roll bar - 4. Rubber bush (in two halves) - 5. Front axle.
ASSEMBLY DRAWING FOR REAR ANTI-ROLL BAR: 4x2 VEHICLES
1. Upper hanger bracket - 2. Link rod - 3. Anti-roll bar - 4. Rubber bush (in two halves) - 5. Rear axle - 6. Cap.
SUSPENSIONS
71
S
TRALIS
AT/AD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст