Iveco Stralis AT/AD. Manual — part 105
70869
70927
46007
70928
Figure 126
Figure 127
Figure 128
Figure 129
In the sequence shown in the figure, position: the supporting
ring (3), clutch plates with internal toothing (2) and clutch
plates with external toothing (1).
Spread IVECO sealant 1905685 onto the surface of the front
box (1) mating with the cover (2). Adjust the key of the oil
pump shaft so that it coincides with the coupling milling of the
transmission shaft. Fit on the cover (2) and tighten the screws
(3) to the prescribed torque.
Using the driver 99374336 (2) and grip 99370007 (1), fit the
seal (3) in the drive input shaft cover (4).
Lubricate the sealing surface of the seal with Unisilikon.
Spread IVECO sealant 1905285 onto the surface of the front
box (1) mating with the cover (2). Mount the cover (2).
Spread LOCTITE 241 onto the thread of the screws (3) and
tighten them to the prescribed torque.
156
GEARBOX EuroTronic 12 AS 2301 D.D./O.D.
S
TRALIS
AT/AD
Base - January 2003
70929
70930
70865
Figure 130
Figure 131
Figure 132
Figure 133
The bushings (2 and 4) and seals (1 and 5) of the lever (3) are
changed by using a suitable drift for removing — fitting new
parts.
Insert the joint pin (4) into the lever (2) and tighten the screws
(3), fixing it to the front box (1), to the prescribed torque.
Turn over the gearbox.
Remove the plate 99370153 (1) and the brackets (3) fastening
the pins (4) from the middle box (2).
Fit: the plate (1) together with the coupling body (2),
adjustment ring (3), connecting sleeve (5) and rod (4).
Complete assembly of the gearbox by refitting the rear box
and the speed actuator as described under the relevant
headings.
On completing assembly, replenish the gearbox with the
prescribed grade and quantity of lubricating oil.
78301
GEARBOX EuroTronic 12 AS 2301 D.D./O.D.
157
S
TRALIS
AT/AD
Clutch release lever
GEARBOX EuroTronic 12 AS 2301 D.D./O.D. with Intarder
159
S
TRALIS
AT/AD
Gearbox EuroTronic
12 AS 2301 D.D./O.D. with Intarder (IT)
Page
SPECIFICATIONS AND DATA
161
. . . . . . . . . . . . .
OVERHAULING THE GEARBOX
162
. . . . . . . . . . .
- Removing the hydraulic retarder
163
. . . . . . . . . . .
- Refitting the hydraulic retarder
163
. . . . . . . . . . . .
- Adjusting epicyclic reduction gear train bearing
end float
163
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Adjusting stator end float
164
. . . . . . . . . . . . . . . .
- Removing the rear box
165
. . . . . . . . . . . . . . . . . .
- Removing the E.R.G
166
. . . . . . . . . . . . . . . . . . . .
- Fitting the E.R.G.
167
. . . . . . . . . . . . . . . . . . . . . . .
EXPERIMENTAL TOOLS
172
. . . . . . . . . . . . . . . . . .
160
GEARBOX EuroTronic 12 AS 2301 D.D./O.D. with Intarder
S
TRALIS
AT/AD
Base - January 2003
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст