Iveco Daily Euro 4. Manual — part 22
75279
75278
75281
75282
Figure 80
Figure 81
Figure 82
Figure 83
Figure 84
Figure 85
Using tool 99360076 (2), remove the oil filter (1).
Take out the coupling (2) and remove the heat exchanger
(1).
Take out the screws (2) and remove the air-conditioner
compressor (1) (if applicable).
Take out the screw (2) and remove the speed sensor (1).
Take out the screws (4) and remove the compressor
mounting (3).
Take out the plug (2) with the seal (3) and extract the oil
pressure control valve (1).
Undo the screws (2) and remove the oil sump (1) with the
associated gasket and frame (3).
108188
108187
F1A ENGINE
75
D
AILY
E
URO
75283
75284
75285
75286
Figure 86
Figure 87
Figure 88
Figure 89
Take out the screws (2), (3), (4) and (5) and remove the
suction strainer (1) together with the pipe (6).
Take out the screws (2) and remove the connecting rod caps
(3).
Extract the pistons (1) from the top of the crankcase.
Block rotation of the flywheel (1) with tool 99360306 (3).
Take out the screws (2) and remove the engine flywheel (1).
Take out the screw (5) and remove the guard (4).
Apply tool 99340058 (2) to the rear O-ring (1) and extract
it from the crankcase.
On the same side of the connecting rod and its
associated cap, indicate the number of the cylinder
from which the connecting rod has been removed.
Keep the bearing shells in their respective housings
since, if they are used, they will need to be fitted in
the position found during removal.
NOTE
76
F1A ENGINE
D
AILY
E
URO
4
75287
75289
75288
75290
Figure 90
Figure 91
Figure 92
Figure 93
Using an appropriate wrench and a hex-fluted wrench, unscrew
the screws (1) and (2) and remove the crankcase base (3).
With the aid of a hoist and a rope, remove the crankshaft (1).
Take out the couplings (1) and remove the oil jets (2).
The central half ring (3) is fitted with thrust half-washers.
Note the assembly position of the bottom main
bearing shells (2) since, if they are reused, they will
need to be fitted in the position found during
removal.
NOTE
Note the assembly position of the top main bearing
shells (2) since, if they are reused, they will need to
be fitted in the position found during removal.
NOTE
On completing engine removal, it is necessary to
clean the removed parts thoroughly and check
their integrity.
The following pages give the instructions for the
main checks and measurements to make in order
to determine whether the parts can be reused.
NOTE
F1A ENGINE
77
D
AILY
E
URO
The measurements must be made for each single cylinder at
three different heights up the liner and on two planes at right
angles to each other: one parallel to the longitudinal axis of
the engine (B) and the perpendicular (A); the greatest wear
is generally found on this last plane with the first
measurement.
On finding ovalization, taper or wear, go ahead and
bore/grind and finish the face of the cylinder liners. The
refacing of the cylinder liners should be done in relation to
the diameter of the pistons supplied as spare parts oversized
by 0.4 mm of the nominal value and to the prescribed
assembly clearance.
18837
75292
Figure 94
Figure 95
After
removing
the
engine,
thoroughly
clean
the
cylinder-crankcase assembly. Use the rings 99365508 to
carry the cylinder block.
Carefully check that the crankcase has no cracks in it.
Check the conditions of processing caps. If the caps are
rusted or if you have even the slightest doubt about their
sealing efficiency, the caps shall be replaced. Apply LOCTITE
270 sealant (IVECO NO. 93162429) to the caps when fitting
the latter back into place.. Examine the surfaces of the
cylinder liners; they must show no sign of meshing, scoring,
ovalization, taper or excessive wear. The inside diameter of
the cylinder liners is checked, to ascertain the extent of
ovalization, taper and wear, using the bore meter 99395687
(1) fitted with a dial gauge previously reset on the ring gauge
of the diameter of the cylinder liner or on a micrometer.
REPAIRS
CYLINDER BLOCK
Checks and measurements
Figure 96
* Surface roughness parameters:
Rt
=
4
÷ 10 μm
Rz
=
3
÷ 8 μm
Ra
=
0,25
÷ 0,6 μm
Wt <
1,5
μm
Permissible surface porosity for machined cylinder
(see Figure 97)
ZONE B1 = Area of greatest mechanical stress,
segment/liner contact:
No.2 non-continuous porosities
are permissible max. 0.5x0.5.
ZONE B2 = Surface involved in segment rubbing:
No.2 non-contiguous porosities
are permissible max. 1x0.8.
100%
100%
75293
Figure 97
C
1
st
measurement
2
nd
measurement
3
rd
measurement
C
78
F1A ENGINE
D
AILY
E
URO
4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст