Iveco Daily Euro 4. Manual — part 159
32
AXLE 5819
D
AILY
E
URO
4
Axle type
5819
WHEEL HUBS
Wheel hubs bearings
UNIT BEARING
Hub bearings end play
-
Wheel hub bearings play
adjustment
Not Adjustable
Fixing nut torque tightening
WHEEL GEOMETRY
Wheel camber angle
(vehicle at static load)
0
o
30’
± 20’
Wheel caster angle
(vehicle at static load)
1
o
35’
± 20’
Wheel toe-in
(vehicle at static load)
2.5
± 1
AXLE 5819
Figure 2
108353
AXLE 5819
33
D
AILY
E
URO
TIGHTENING TORQUES
PART
TORQUE
PART
Nm
kgm
Screw securing caliper mounting to stub axle
176
÷ 217
18
÷ 22
1
Nut securing the upper swinging arm jointed head to the stub axle
157
÷ 177
15.7
÷ 17.7
2
Nut securing the steering rod jointed head to the lever
68
÷ 83
6.8
÷ 8.3
3
Nut securing the lower swinging arm jointed head to the stub axle
157
÷ 177
15.7
÷ 17.7
4
Nut securing wheel hub
320
÷ 420
32
÷ 42
5
Screw securing plate and brake disc to wheel hub
98
÷ 108
9.8
÷ 10.8
7
Nut securing wheel
180
÷ 200
18
÷ 20
Screw securing guards to stub axle
7
÷ 10
0.7
÷ 1
34
AXLE 5819
D
AILY
E
URO
4
TOOL NO.
DESCRIPTION
99305354
Portable optical reading tool for checking wheel trim
99306010
Apparatus to purge air from brakes and clutch
99321024
Hydraulic trolley for removing/refitting wheels
99322215
Driving and steering axle overhaul stand
99347074
Tool for extracting steering tie rod king-pins
99357144
Wrench for spindle pin ring nut
Set upper and lower lever kingpins (6 and 8) into stub axle
seat (4) then tighten self-locking nuts (1 and 5) to the
prescribed torque.
Refit steering lever (3) on stub axle by tightening the relevant
fixing screw and nut (7) to the prescribed torque.
Refit dust cover (2) to stub axle by means of the proper
screws indicated with arrows.
19026
19027
19028
Figure 3
Removal
REPAIR OPERATIONS
The following paragraphs describe the overhaul operations
that differ from axle 5818 operations.
To remove and refit axle 5819, proceed in a similar manner
as for axle 5823.
Adjustment values, tightening torque values and equipment
are those specified in this chapter.
520610
AXLE 5819 OVERHAUL
520611
Stub axle removal and refitting
Remove wheel hub as described in the relevant chapter
(operation 520620) concerning axle 5817.
Remove from stub axle (5):
- dust cover (2) by loosening screw (7);
- steering lever (3) by loosening screw (8);
Loosen kingpin (1 and 6) fixing nuts from stub axle (5).
Refitting
Use tool 99347074 (3) to remove kingpin (1) from stub axle
(2) then remove the latter.
Figure 4
Figure 5
Self-locking nuts (1 and 5) cannot be reused after
removing.
Refit wheel hub as described in the relevant
chapter (operation 520620) concerning axle 5818.
NOTE
AXLE 5819
35
D
AILY
E
URO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст