Iveco Daily. Manual — part 114
F1
A
E
NG
INE
D
AI
LY
434
B
as
e
-
M
ay
2004
P
rin
t
603.
93.
281
BLINK
CODE
EDC
LAMP
POSSIBLE
CAUSE
POSSIBLE
TROUBLE
TESTS OR
RECOMMENDED ACTION
NOTES
3.7
Off
Glow
plug
relay
short-circuited or circuit
open.
Shorted to +Batt or circuit
open: the glow plugs do not
work, starting may be difficult
and smokiness on starting.
Shorted to earth: the glow
plugs are always powered
(short life).
Check
the
wiring
of
the
EDC
connector pin B42 to find the shorting
to +Batt or to earth or the break in the
circuit.
Check the integrity of the pre-heating
control unit.
Check
the
60A
fuse
connected
between the battery positive and the
pre-heating control unit connector pin
30.
Check the power supply is correct on
pin 86 of the pre-heating control unit
and on the EDC connector pin B42.
Check the earth connection of the
pre-heating control unit pin 31.
3.9
Off
Glow plugs short-circuited
or circuit open.
Starting difficult with very
rigid outdoor temperatures.
Smokiness on starting.
Check the integrity of the single glow
plugs.
Check the glow plug power supply
between the pre-heating control unit
connector pin G1 — G2 — G3 — G4 and
earth.
If all OK, change the pre-heating
control unit.
5.1
Blinking
Electro-injector
cylinder
no. 1 shorted to +Batt.
or
shorted to earth or circuit
open.
Drop in power made by the
EDC control unit.
The
engine
runs
on
2
cylinders.
Possibly 3.1.
The
engine
runs
on
3
cylinders.
Check the wiring and connections
between the injector and the EDC
connector pin A12 — A40.
If the wiring is good, change the
injector.
F1
A
E
NG
INE
435
D
AI
LY
B
as
e
-
M
ay
2004
P
rin
t
603.
93.
281
BLINK
CODE
EDC
LAMP
POSSIBLE
CAUSE
POSSIBLE
TROUBLE
TESTS OR
RECOMMENDED ACTION
NOTES
5.2
Blinking
Electro-injector
cylinder
no. 2 shorted to +Batt.
or
shorted to earth or circuit
open.
Drop in power made by the
EDC control unit.
The
engine
runs
on
2
cylinders.
Possibly 3.2.
The
engine
runs
on
3
cylinders.
Check the wiring and connections
between the injector and the EDC
connector pin A10 — A43.
If the wiring is good, change the
injector.
5.3
Blinking
Electro-injector
cylinder
no. 3 shorted to +Batt.
or
shorted to earth or circuit
open.
Drop in power made by the
EDC control unit.
The
engine
runs
on
2
cylinders.
Possibly 3.3.
The
engine
runs
on
3
cylinders.
Check the wiring and connections
between the injector and the EDC
connector pin A23 — A42.
If the wiring is good, change the
injector.
5.4
Blinking
Electro-injector
cylinder
no. 4 shorted to +Batt.
or
shorted to earth or circuit
open.
Drop in power made by the
EDC control unit.
The
engine
runs
on
2
cylinders.
Possibly 3.4.
The
engine
runs
on
3
cylinders.
Check the wiring and connections
between the injector and the EDC
connector pin A24 — A41.
If the wiring is good, change the
injector.
5.7
Blinking
Power stage to supply the
electro-injectors
of
cylinders 1 and 4 (in control
unit) defective.
Possibly 3.1 — 3.4.
The
engine
runs
on
2
cylinders
Delete the fault memory and try again.
If the error remains and only after
excluding the injector 1 or 4 defect, call
the Help Desk and follow their
instructions to replace the control unit
if necessary.
F1
A
E
NG
INE
D
AI
LY
436
B
as
e
-
M
ay
2004
P
rin
t
603.
93.
281
BLINK
CODE
EDC
LAMP
POSSIBLE
CAUSE
POSSIBLE
TROUBLE
TESTS OR
RECOMMENDED ACTION
NOTES
5.8
Blinking
Power stage to supply the
electro-injectors
of
cylinders 2 and 3 (in control
unit) defective.
Possibly 3.2 — 3.3.
The
engine
runs
on
2
cylinders
Delete the fault memory and try again.
If the error remains and only after
excluding the injector 2 or 3 defect, call
the Help Desk and follow their
instructions to replace the control unit
if necessary.
6.1
Blinking
Crankshaft sensor: no signal
or implausible signal.
The engine will not start cold,
it could start warm with
difficulty.
With the engine running,
power
reduction
and
increased noise.
Check the integrity of the sensor (R =
approx. 850 Ohm).
If the sensor is sound, check the wiring
between
the
sensor
and
EDC
connector pin A29 — A37.
Check the sensor is fastened properly.
If there is no crankshaft signal, the camshaft sensor
speed signal is used instead.
Power reduction (and noise reduction because
the control unit cannot manage advance and
duration of injection and bases itself on a recovery
map. Pre-injection is not implemented).
6.2
Blinking
Camshaft sensor: no signal
or implausible signal.
The engine will not start cold,
it could start warm with
difficulty.
With the engine running,
power
reduction
and
increased noise.
False
injections
during
starting and smoke at the
exhaust.
Check the integrity of the sensor (R =
approx. 850 Ohm).
If the sensor is sound, check the wiring
between
the
sensor
and
EDC
connector pin A4 — A31.
Check the sensor is fastened properly.
If there is no camshaft signal, the flywheel sensor
timing signal is used instead.
6.4
Off
The
engine
has
over-revved (over 5500
rpm), probably driven,
or
crankshaft sensor signal not
plausible (in this case, error
6.1 signalled).
If the over-revving occurred
when driven, the driver can
detect no reaction (other
than
the
indicator
light
blinking).
Data saved to memory, check the
duration
and
frequency
of
the
over-revving.
Delete the fault memory.
Make the driver aware about using the vehicle
correctly.
F1
A
E
NG
INE
437
D
AI
LY
B
as
e
-
M
ay
2004
P
rin
t
603.
93.
281
BLINK
CODE
EDC
LAMP
POSSIBLE
CAUSE
POSSIBLE
TROUBLE
TESTS OR
RECOMMENDED ACTION
NOTES
8.1
Blinking
Pressure in rail too great.
The electric command fails
to reach the pressure
regulator.
The engine cuts out, loud
noise before cutting out.
Check that the connector on the
pressure regulator is connected.
If it is connected, check the wiring
between the regulator and the EDC
connector pin A9 — A20.
After a few times, the pressure relief valve might
remain open, in which case it has to be changed.
8.1
Blinking
Pressure in rail too great.
Pressure regulator
mechanically jammed
open.
The engine cuts out, loud
noise before cutting out.
Perform the high-pressure test with the
diagnosis instrument. If the outcome is
negative, replace the high-pressure
pump — regulator assembly.
After a few times, the pressure relief valve might
remain jammed open, in which case it has to be
changed.
8.1
Blinking
Pressure in rail too low.
Pressure regulator
mechanically jammed shut.
The engine cuts out or fails
to start.
Perform the high-pressure test with the
diagnosis instrument. If the outcome is
negative, replace the high-pressure
pump — regulator assembly.
8.1
Blinking
Pressure in rail too low.
Shorting to +Batt. on the
pressure regulator.
The engine cuts out or fails
to start.
Check
the
wiring
between
the
regulator and EDC connector pin A9 —
A20.
8.1
Blinking
Pressure in rail too low.
High-pressure pump
defective.
The engine cuts out or fails
to start.
Perform the high-pressure test with the
diagnosis instrument. If the outcome is
negative, replace the high-pressure
pump together with the regulator.
8.1
Blinking
Injector mechanically
jammed open.
The engine cuts out or fails
to start.
Perform the cylinder efficiency test
with the diagnosis instrument. If the
outcome is negative, replace the
defective injector.
8.1
Blinking
Pressure in rail too low.
Major fuel leak from the
high-pressure circuit.
The engine cuts out or fails
to start.
Check the high-pressure circuit and
eliminate the leak (beware, there could
be a leak inside the head between the
high-pressure union and the injector).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст