Iveco Daily. Manual — part 156
M
O
T
O
R
I
F1A
-
F1C
520
F1C ENGINE
D
AILY
Base - May 2004
MOTORI F1A - F1C
F1C ENGINE
521
D
AILY
Base - May 2004
MOTORI F1A - F1C
522
F1C ENGINE
D
AILY
Base - May 2004
F1C ENGINE
523
D
AILY
Base - May 2004
PART
TORQUE
PART
Nm
kgm
M15x1.5 L 193 fastening screw for cylinder head inside
First stage: pre-tightening
130
13
Second stage: angle
90º
Third stage: angle
90º
M12x1.5 L 165 fastening screw for cylinder head side
First stage: pre-tightening
65
6.5
Second stage: angle
90º
Third stage: angle
60º
M8x1.25 L 117/58 fastening screw for side with chain compartment, cylinder head
25
2.5
R 1/2”bevel threaded cap with socket head
25
2.5
R 3/8” bevel threaded cap with socket head
17
1.7
R 1/4” bevel threaded cap with socket head
9
0.9
M26x1.5 threaded screw tap
50
5
Screw with flange M6x1 for camshaft rear cover fastening
10
1
Screw with flange M6x1 for camshaft shoulder plate fastening
10
1
Socket head screw with flange M8x1.25 L 30/40/77/100 for over-head fastening
25
2.5
M14x1.5 L 10 threaded screw tap
25
2.5
M6x1 socket head screw for timing system control cover
10
1
M12x1.5 L 125 inner fastening screw for lower cylinder block
First stage: pre-tightening
50
± 5
5
± 0.5
Second stage: angle
60º
± 2.5º
Third stage: angle
60º
± 2.5º
M8x1.25 L 77.5/40 outer fastening screw for lower cylinder block
26
2.6
Socket head screw with flange M11x1.25 for connecting rod cap fastening
First stage: pre-tightening
50
5
Second stage: angle
70
°
Socket head screw with flange M12x1.25 for engine flywheel fastening
First stage: pre-tightening
30
3
Second stage: angle
90
°
Socket cylinder head screw for phonic wheel fastening on drive shaft
15
1.5
Connection M10x1 for piston cooling nozzle
25
2.5
Bevel threaded cap with socket head R 3/8”x10 oil circuit
17
1.7
Socket head screw with flange M18x1.5 for drive shaft damper pulley fastening
350
35
Bevel cap R 1/8 x 8
7
0.7
Water draining plug M14x1.5 L10
25
2.5
Pipe union on block for oil return from turbocharger G 3/8” x 12
50
5
Suction rose M6x1 fastening screw
10
1
Socket head nut with flange M8x1.25 for depressor — oil pump unit support fastening
25
2.5
Oil pump — depressor unit control pin
110
11
Threaded cap M26x1.5
50
5
Socket head screw with flange M8x1.5 L35 for oil sump retaining frame fastening
25
2.5
Threaded screw tap with O-ring M22x1.5 L10
50
±10
5
±1
Socket head screw with flange M8x1.25 L60 for depressor - oil pump unit fastening
25
2.5
Socket head screw with flange M8x1.25 L50 for depressor - oil pump unit fastening
25
2.5
Flanged screw M8x1.25 L20/30 for camshaft cover fastening
25
2.5
Flanged screw M6x1 L20 for blow-by unit fastening
10
1
M14x1.5 L10 cap
25
2.5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст