Iveco Daily. Manual — part 25
Check valve tappet (1) diameter, with a micrometer (2) and
with an inside micrometer gauge the diameter of relevant
seats on cylinder head; they must be equal to those indicated
in Figure 125. The normal fitting clearance between the
maximum diameter of valve tappet and that of seats is
0.030
÷ 0.075 mm.
The replacement of valve tappet, because of an excessive
clearance in the seats, requires to fit oversized valve tappet
after boring the seats by means of a suitable reamer.
540662
Disassembling valves
41113
Valve dismantling is performed with tool 99360268 (1) by
exerting a pressure on cap (3) so that, pressing springs (4 and
5) it is allowed to remove lock cones (2). Then remove:
upper cap (3), springs (4 and 5) and lower cap (6).
Repeat operation on all valves.
Overturn cylinder head and remove valves (7).
25227
MAIN DATA ON VALVE TAPPET AND RELEVANT
SEAT ON CYLINDER HEAD
43,950
÷ 43,970
44,000
÷ 44,025
Figure 125
Figure 126
Figure 127
Figure 128
Figure 129
541211
Checking cam lift and journal align-
ment
Set shaft on centres and check, with a centesimal dial gauge
placed on central support, that alignment error is no greater
than 0.04 mm, otherwise replace shaft. Also check cams lift:
it should be 10.5 mm for those of outlet and 9.5 mm for
those of inlet; if different values are found replace the shaft.
18877
Extract valve tappet (1) complete with adjusting caps, placing
them in a container according to the order they were when
removed.
Lateral surface of valve tappet must be very smooth and dent
free.
Small dents can be eliminated with a very fine abrasive stone.
18891
Using suitable pliers (1), remove the seal rings (2) from the
valve guides.
50674
541224
VALVE TAPPET
ENGINES 8140.43R/B/S/N
82
D
AILY
Base - May 2004
Check for hydraulic leak by means of suitable equipment
(1-2-3-4).
Supply water, through pump, heated at
~ 90°C and at 2 ÷ 3
bar pressure.
Should plug leaks be found, replace them using a proper
beater for removal/refitting.
MAIN DATA ON INTAKE AND EXHAUST VALES AND
VALVE GUIDES
18542
18879
41115
18625
Figure 130
Figure 131
Figure 132
Figure 133
Figure 134
The check of mating surface of the head (1) to cylinder group
is performed by means of a rule (2) and a thickness gauge (3).
If a deformation is found, measure cylinder head thickness,
whose rated value is 150
± 0.1 mm.
When checking, if the amount of material to be removed for
flattening cylinder head is greater than 0.4 mm, replace
cylinder head.
Remove any carbonic deposits on valves, using the special
metal brush.
Check that valves do not show any trace of seizure, crack or
burning. Regrind seats on valves, if necessary, with grinder
99301014, removing an amount of material, as little as
possible.
Checking cylinder head seal
Checking cylinder head mating surface
540662
VALVES
Removing
deposits,
refacing
and
checking
valves
INTAKE
EXHAUST
If there is any leakage from the cylinder head, it must be
replaced.
18882
With a micrometer (2) measure valve stem (1): it must be
7.985
÷ 8.00 mm.
Before mounting the plugs, apply water-reacting
sealant on their sealing surfaces.
NOTE
ENGINES 8140.43R/B/S/N
83
D
AILY
Base - May 2004
These checks are carried out with a magnetic-base dial gauge
(1) set as shown. Assembly clearance is 0.023
÷ 0.053 mm.
On emptying valve (2) check that centring error is not
greater than 0.03 mm.
Once valve guides are driven, sleek them with smoothing
tool 99390310 (1).
41842
Figure 135
Figure 136
Figure 137
Figure 138
Figure 139
Figure 140
Checking clearance between valve stem and
valve guide and centring valves
Remove valve guide with punch 99360288 (1).
18883
18885
Heat cylinder head to 80
° ÷ 100°C and with punch
99360288 (1) equipped with part 99360291 (2) fit new valve
guide (3) previously cooled in liquid nitrogen.
41116
Valve guide fitting.
18886
Check valve seats (2). If any slight scoring or burning is found
regrind them with tool HUNGER 99360419 (1) according to
inclination values specified in Figure 141.
If it is required to replace them, using the same tool and taking
care not to damage the cylinder head, remove as much
material as possible from valve seats, until it is possible to
extract them from the cylinder head with a punch.
18887
540667
VALVE GUIDES
Replacing valve guides
Reaming valve guides
540661
VALVE SEATS
Regrinding and replacing valve seats
ENGINES 8140.43R/B/S/N
84
D
AILY
Base - May 2004
Fit valves and injectors.
Check valve sealing and respective seats with tools (1-2).
18888
18890
Figure 141
Figure 142
Figure 143
Figure 144
MAIN DATA ON VALVE SEATS
Heat cylinder head to 80
° ÷ 100°C and, by means of a
suitable punch (1), fit in it the new valve seats (2), previously
cooled in liquid nitrogen.
With tool HUNGER 99360419, regrind valve seats according
to inclination values specified in Figure 141.
Clean injector seats from any deposit, using cutter 99394038
(1).
Figure 145
50675
1
2
18880
With dial gauge (1) check that, from cylinder head surface,
the hollow of valves and injector (2) protrusion have the
prescribed value.
1
2
18889
EXHAUST
INTAKE
REFERENCE 34.8
∅
REFERENCE 39.7
∅
3.6
÷
3.7
10.5
÷
10.45
ENGINES 8140.43R/B/S/N
85
D
AILY
Base - May 2004
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст