Iveco EuroCargo (12 to 26 t). Manual — part 155
Figure 32
500910 FRONT SHOCK ABSORBERS
Removal
Loosen upper nut (1) and lower nut (5), take the pads (2) and
(4) and remove the shock absorber (3) from the vehicle.
Refitting
Refit by reversing the removal sequence. Fasten
screws and nuts at the specified torque.
72819
Figure 33
500711
FRONT AIR SPRINGS
Removal
Disconnect the air supply tube (1).
Loosen the upper fastening screws (2) and the lower
fastening screws (4). Remove the air springs from the vehicle.
Refitting
Refit by reversing the removal sequence. Fasten
screws and nuts at the specified torque.
72820
E
URO
C
ARGO
T
ECTOR
12-26 t
72
FRONT AND REAR PNEUMATIC SUSPENSIONS
Base - February 2003
528930
FRONT SWAY BAR
Removal
On the lower side of the vehicle, loosen the front
U-bolt (3) nuts (4) and remove from the housing.
- Loosen the nuts (2) fastening the sway bar connecting
rod to the chassis mount.
- Remove the mounts from the axle and remove the sway
bar (5) with connecting rod from the vehicle.
72821
Figure 34
!
Disconnect the battery cables before starting
removal-refitting operations.
Refit by reversing the removal sequence. Fasten
screws and nuts at the specified torque.
Lock nuts must be replaced and fastened at the
specified torque.
Check that:
- U-bolt threading is in good conditions. If
required, reface the threading or replace the
part.
Refitting
Refit by reversing the removal sequence. Fasten
screws and nuts at the specified torque.
Lock nuts must be replaced and fastened at the
specified torque.
Check that:
- U-bolt threading is in good conditions. If
required, reface the threading or replace the
part.
Refitting
A = Part seen from the right-hand side of the vehicle.
Removal
Arrange the vehicle on level ground, block the
rear wheels with wedges and proceed as follows:
- Loosen the front wheel fastening nuts, lift the vehicle and
position it on stands.
- Arrange hydraulic jack 99321024 under the wheels,
remove the fastening nuts and remove the wheels.
- Loosen the nuts (6), taking the pad (10) and remove the
shock absorber (14).
- On the lower side of the vehicle, loosen the nuts (4) and
remove the U-bolt (3) taking the plate (11).
- Loosen the nut and remove the rear pin (13) anchoring
the leaf spring (12) to the chassis mount.
- Loosen the nut and remove the front leaf spring (12)
anchoring pin (1) to the chassis mount. Lower the axle
and remove the complete leaf spring.
- Loosen the nut (9) and disconnect the tie-rod (8).
- Loosen the nut (7), remove the screw and disconnect
the air spring from the leaf spring.
E
URO
C
ARGO
T
ECTOR
12-26 t
FRONT AND REAR PNEUMATIC SUSPENSIONS
73
Base - February 2003
FRONT PNEUMATIC SUSPENSION
REMOVAL-REFITTING
72822
Figure 35
!
Disconnect the battery cables before starting
removal-refitting operations.
Removal
Arrange the vehicle on level ground, block the
rear wheels with wedges and proceed as follows:
- Loosen the front wheel fastening nuts, lift the vehicle and
position it on stands in the point shown by (
⇒).
- Arrange hydraulic jack 99321024 under the wheels,
remove the fastening nuts and remove the wheels.
- Loosen nut (13) and remove the shock absorber (14).
- Remove the air spring (2) and (11) fastening nuts (4) and
(9).
- Remove the sway bar (10) fastening bolts (8).
- Loosen the fastening nuts and disconnect the level valve
tie-rid (12).
- Loosen the fastening nuts (6), taking the plates and
remove the U-bolts (15).
- Loosen the reaction rod (3) fastening bolts (1) and (7).
- Remove the suspension arms from the vehicle (5).
Refitting
(Models 120E..P-FP/130E..P-FP/150E..P-FP)
!
The following paragraph describes the procedure for
model 130E..FP and is suitable also for the other
models.
Refit by reversing the removal sequence. Fasten
screws and nuts at the specified torque.
Lock nuts must be replaced and fastened at the
specified torque.
Check that:
- U-bolt (15) threading is in good conditions. If
required, reface the threading or replace the
part.
E
URO
C
ARGO
T
ECTOR
12-26 t
74
FRONT AND REAR PNEUMATIC SUSPENSIONS
Base - February 2003
REAR PNEUMATIC SUSPENSION
REMOVAL-REFITTING
72823
Figure 36
Removal
- Disconnect the air supply tubes (4).
- Loosen the chassis fastening screws (1).
- Loosen the nuts (3) and remove the air springs (2).
Refitting
Refit by reversing the removal sequence. Fasten
screws and nuts at the specified torque.
500940
REAR SHOCK ABSORBERS
500731
REAR AIR SPRINGS
72827
Figure 37
Removal
- Loosen the lower fastening nuts (4).
- Loosen the upper fastening nuts (1) and take the pads.
- Remove the shock absorbers from the vehicle (3).
Refitting
Refit by reversing the removal sequence. Fasten
screws and nuts at the specified torque.
E
URO
C
ARGO
T
ECTOR
12-26 t
FRONT AND REAR PNEUMATIC SUSPENSIONS
75
Base - February 2003
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст