Iveco EuroCargo (12 to 26 t). Manual — part 111
Remove differential gear (2) with the associated thrust washer
(1). Remove spider (6) with the four planetary gears (5)
complete with thrust washers (3). Take the spider/planetary
gear assembly apart. Remove the other differential gear with
its thrust washer from the half cage (4).
Use hook (1) to raise the gear cage assembly and position on
stand 99371047 (3).
19379
36316
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Unscrew nuts (1) and remove them with screws. Drive out
bevel crown wheel (2).
Dismantling gear cage
36317
Use tool 99348001 (1) and reaction block 99345055 (2) to
remove bearing (3) and bearing (4).
19383
19382
Mark the two casing halves (2 and 3) and the spider as
indicated in the figure.
Unscrew screws (1) joining the casing halves. Lift the casing half
(2).
526249
Dismantling bevel pinion support
19384
Prevent the flange from rotating using tool 99370317 (2) and
use a universal extractor or appropriate tool (1) to remove
the transmission attachment flange from the bevel pinion.
E
URO
C
ARGO
T
ECTOR
12-26 t
AXLES IN TANDEM MERITOR (REAR)
67
36318
36319
Figure 24
Figure 25
Figure 26
Figure 27
Position the pinion support under a press and drive out bevel
pinion (2) complete with intermediate bearing, rear bearing
and adjustment ring from bevel pinion support (1). Remove
adjustment ring from bevel pinion.
Apply tool 99348001 (2) under taper roller bearing (1) and use
a press to remove from bevel pinion (3). If necessary, remove
rear bearing (4) from bevel pinion (3) in the same way
(destructive operation).
19388
19389
Use a punch to remove seal carrier cover (2) from bevel
pinion support (1). Then remove front bearing from support.
Apply a drift to the point arrowed in the diagram and drive out
outer race (2) of front bearing from bevel pinion support (3).
Upturn the support and remove the intermediate bearing
outer race (1).
E
URO
C
ARGO
T
ECTOR
12-26 t
68
AXLES IN TANDEM MERITOR (REAR)
Base - February 2003
20958
Figure 28
DIFFERENTIAL COMPONENTS (with differential lock)
1. Bevel pinion nut - 2. Flange - 3. Deflector - 4 .Seal holder cover - 5. Screw - 6. Washer - 7. Front bearing - 8. Outer race - 9.
Support - 10. Adjustment shim - 11. Adjustment ring - 12. Outer race - 13. Intermediate bearing - 14. Bevel pinion -
15. Rear bearing - 16. Lock nut - 17. Sending unit - 18. Plug - 19. Adjustment ring nut - 20. Spring - 21. Shaft - 24 .Cylinder - 25.
Piston - 26. Sealing ring - 27. Copper ring - 28. Cover - 29. Screws - 30. Screw - 31. Washers - 32. Copper washer -
33. Threaded plug - 34 .Sliding sleeve - 35. Roll pins - 36. Fork - 37. Screws - 38. Washer - 39. Plate - 40. Screw -
41. Washer - 42. Cap - 43. Thrust washer - 44. Planetary gear - 45. Differential gear - 46. Thrust washer - 47. Half cage -
48. Bearing - 49. Outer race - 50. Screw - 51. Spider - 52. Screw - 53. Bevel crown wheel - 54. Half cage - 55. Nut -
56. Cap - 57. Locking pin - 58. Differential casing
E
URO
C
ARGO
T
ECTOR
12-26 t
AXLES IN TANDEM MERITOR (REAR)
69
36321
36321
Figure 29
Figure 30
SECTION OF DIFFERENTIALS PR 140 E (R0868)
View of differential unit with differential lock device.
E
URO
C
ARGO
T
ECTOR
12-26 t
70
AXLES IN TANDEM MERITOR (REAR)
Base - February 2003
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст