Iveco EuroCargo (12 to 26 t). Manual — part 130
60887
60889
Steering knuckle bearing replacement (5) is made using for
their disassembly and assembly beater’s elements (1-2-3)
99374529 and handle 99370007 (4).
Use element (1) and handle (4) to disassemble the sealing
ring (8) and the roller bearings (6-7) on the upper side.
Use element (3) and handle (4) to disassemble the sealing
ring (9) and the roller bearings (10-11) on the lower side.
520615
STEERING KNUCKLE PIN
BEARING REPLACEMENT
Figure 51
Figure 52
Roller bearing assembly (7):
use element (1 and 2) and handle (4).
Roller bearing assembly (6):
use element (2) and handle (4).
Roller bearing assembly (8):
use elements (3 and 2) and handle (4).
Roller bearing assembly (9):
use element (2) and handle (4).
Figure 53
Use locking ring 99374173 (2) and handle 99370007 (1) to
place the lower seal; use locking ring (3) 99374172 and
handle 99370007 (1) to place the upper seal in the steering
knuckle.
34556
E
URO
C
ARGO
T
ECTOR
12-26 t
64
FRONT AXLES 5842/5 - 5851/5
Base - February 2003
Figure 55
Figure 54
Check flatness of leaf spring surfaces compared
to holes for steering knuckle pins
Place two bars (1) fitted with cones (3) in the steering
knuckle pin holes. Push the cones and clamp them placing the
appropriate screws on the bars.
Introduce two centring dowels (2) in the leaf spring support-
ing plane (4).
Place on the planes (6) two bases (5) using goniometers and
introduce them in the centring dowels.
Before placing the bases with the goniometers,
check that the supporting planes are not painted or
irregular.
!
Check the angle of deformation on the goniometers’ grad-
uated sector shown by the arrows.
Goniometers’ indexes will, of course, detect no angle move-
ment when the flatness of leaf spring surfaces compared to
the steering knuckle pin holes is correct.
Remove the sliding bar and the goniometer’s bases used to
make the survey.
Place the sliding bar (2) on the goniometer’s bars (4), adjusting
its length so that the shaped edges touch the bars (1).
Clamp the screw of the stop block (7) and the goniometer’s
lock screws (3) to the bars (4).
Figure 56
E
URO
C
ARGO
T
ECTOR
12-26 t
FRONT AXLES 5842/5 - 5851/5
65
Base - February 2003
CHECKS AND MEASUREMENTS
OF THE AXLE UNIT
Figure 57
Figure 58
Check hole inclination for steering knuckle
pins
Place on the bars (1) the supports (3) fitted with gonio-
meters and screw the screws (2) without clamping them.
Introduce the connecting cross tie rod (4) and tighten the
screws (2) which clamp the supports touching the bars (1).
Check the angle of inclination value concerning the steering
knuckle pin holes on the related graduated sectors (2), next
to the gauge (1). The angle of inclination concerning the
steering knuckle pin holes must be 7
° ± 0°3’.
E
URO
C
ARGO
T
ECTOR
12-26 t
66
FRONT AXLES 5842/5 - 5851/5
Base - February 2003
E
URO
C
ARGO
T
ECTOR
12-26 t
FRONT AXLE 5871/5
67
Base - February 2003
5206
Front axle 5871/5
Page
DESCRIPTION
69
. . . . . . . . . . . . . . . . . . . . . . . . . .
- Characteristic angles
71
. . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS AND DATA
73
. . . . . . . . . . . . .
DIAGNOSTICS
75
. . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUES
78
. . . . . . . . . . . . . . . . .
TOOLS
79
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT WHEEL SET UP
83
. . . . . . . . . . . . . . . . . .
- Setting of clips and headlights
83
. . . . . . . . . . . . .
- Electronic compensation for rim maladjustment
84
- Wheel alignment
84
. . . . . . . . . . . . . . . . . . . . . . .
- Toe-in check
85
. . . . . . . . . . . . . . . . . . . . . . . . . .
- Check of wheel inclination (Camber)
85
. . . . . . .
- Check upright angle of inclination (King Pin)
and clearance angle (Caster)
85
. . . . . . . . . . . . . .
- Check steering angles
86
. . . . . . . . . . . . . . . . . . .
OVERHAULING THE FRONT AXLE ASSEMBLY
(MECHANICAL AND PNEUMATIC
SUSPENSION)
87
. . . . . . . . . . . . . . . . . . . . . . . .
OVERHAULING THE FRONT AXLE ASSEMBLY
87
- Removing the wheel hubs
87
. . . . . . . . . . . . . . . .
- Replacing the wheel hub bearings
87
. . . . . . . . . .
- Replacing seal
88
. . . . . . . . . . . . . . . . . . . . . . . . .
- Replacing wheel studs
88
. . . . . . . . . . . . . . . . . . .
- Refitting wheel hubs
89
. . . . . . . . . . . . . . . . . . . .
- Adjusting wheel hub bearing end play
89
. . . . . . .
- Checking the rolling torque
89
. . . . . . . . . . . . . . .
REMOVING AND REFITTING TRACK ROD
90
. .
REPLACING TRACK ROD BALL JOINT
90
. . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст