KIA Sorento (2019 year). Instruction — part 26

5 133

Driving your vehicle

If you do decide to pull a trailer

Here are some important points if
you decide to pull a trailer:
• Consider using a sway control. You

can ask a hitch dealer about sway
control.

• Do not do any towing with your

vehicle during its first 1,200 miles
(2,000 km) in order to allow the
engine to properly break in. Failure
to heed this caution may result in
serious engine or transmission
damage.

• When towing a trailer, be sure to

consult an authorized Kia dealer
for further information on additional
requirements such as a towing kit,
etc.

• Always drive your vehicle at a mod-

erate speed (less than 60 mph
(100 km/h)).

• On a long uphill grade, do not

exceed 45 mph (70 km/h) or the
posted towing speed limit,
whichever is lower.

• The chart contains important con-

siderations that have to do with
weight:

Item

Theta II 2.4

Lambda II 3.3

Maximum

trailer

weight

Without brake

System

1,650 (750)

1,650 (750)

With brake

System

2,000 (907)

2,000 (907)

With trailer

package

-

2WD : 3,500 (1,587)
4WD : 5,000 (2,267)

Maximum tongue weight

280 (127)

350 (159)

To identify what the vehicle trailering capacity is for your vehicle, you should
read the information in “Weight of the Trailer” that appears later in this sec-
tion.

[lbs.(kg)]

UMA PE USA 5.QXP 12/22/2017 3:40 PM Page 133

Driving your vehicle

134

5

Weight of the trailer

What is the maximum safe weight of
a trailer? It should never weigh more
than the maximum trailer weight with
trailer brakes. But even that can be
too heavy.
It depends on how you plan to use
your trailer. For example, speed, alti-
tude, road grades, outside tempera-
ture and how often your vehicle is
used to pull a trailer are all important.
The ideal trailer weight can also
depend on any special equipment
that you have on your vehicle.

Weight of the trailer tongue

The tongue load of any trailer is an
important weight to measure
because it affects the total gross
vehicle weight (GVW) of your vehi-
cle. This weight includes the curb
weight of the vehicle, any cargo you
may carry in it, and the people who
will be riding in the vehicle. And if you
will tow a trailer, you must add the
tongue load to the GVW because
your vehicle will also be carrying that
weight.

The trailer tongue should weigh a
maximum of 10% of the total loaded
trailer weight, within the limits of the
maximum permissible trailer tongue
load. After you've loaded your trailer,
weigh the trailer and then the tongue,
separately, to see if the weights are
proper. If they aren’t, you may be
able to correct them simply by mov-
ing some items around in the trailer.

C190E01JM

Tongue Load

Total Trailer Weight

C190E02JM

Gross Axle Weight

Gross Vehicle Weight

WARNING

- Trailer

Always follow the loading
instructions provided with your
trailer.

Improper loading can

effect vehicle operation and
result in an accident.

UMA PE USA 5.QXP 12/22/2017 3:40 PM Page 134

5 135

Driving your vehicle

VEHICLE LOAD LIMIT

The label located on the driver's door sill gives the original tire size, cold tire pressures recom-
mended for your vehicle, the number of people that can be in your vehicle and vehicle capacity
weight.

OUMA054204/OUMA054205/OUMA054206/OUMA054207/OUMA054208/OUMA054209

Tire and loading information label

UMA PE USA 5.QXP 12/22/2017 3:41 PM Page 135

Driving your vehicle

136

5

Vehicle capacity weight:

5 persons : 930 lbs. (420kg)
7 persons : 1,120 lbs. (506kg)

Vehicle capacity weight is the maxi-
mum combined weight of occupants
and cargo. If your vehicle is equipped
with a trailer, the combined weight
includes the tongue load.

Seating capacity:

Total - 5 persons

(Front seat : 2 persons,
Rear seat : 3 persons)

- 7 persons

(Front seat : 2 persons,
Rear seat : 5 persons)

Seating capacity is the maximum
number of occupants including a
driver, your vehicle may carry.
However, the seating capacity may
be reduced based upon the weight of
all of the occupants, and the weight
of the cargo being carried or towed.
Do not overload the vehicle as there
is a limit to the total weight, or load
limit including occupants and cargo,
the vehicle can carry.

Towing capacity:

* 2.4 L Engine
Without trailer brakes
: 1,650 lbs. (750 kg)
With trailer brakes
: 2,000 lbs. (907 kg)
With trailer package
: N/A

* 3.3L Engine
Without trailer brakes
: 1,650 lbs. (750 kg)
With trailer brakes
: 2,000 lbs. (907 kg)
With trailer package
: 2WD : 3,500 lbs. (1,587 kg)

4WD : 5,000 lbs. (2,267 kg)

Towing capacity is the maximum
trailer weight including its cargo
weight, your vehicle can tow.

UMA PE USA 5.QXP 12/22/2017 3:41 PM Page 136

5 137

Driving your vehicle

Cargo capacity:

The cargo capacity of your vehicle
will increase or decrease depending
on the weight and the number of
occupants and the tongue load, if
your vehicle is equipped with a trailer.

Steps for determining correct
load limit

1.Locate the statement “The com-

bined weight of occupants and
cargo should never exceed XXX kg
or XXX lbs.” on your vehicle's plac-
ard.

2.Determine the combined weight of

the driver and passengers that will
be riding in your vehicle.

3.Subtract the combined weight of

the driver and passengers from
XXX kg or XXX lbs.

4.The resulting figure equals the

available amount of cargo and lug-
gage load capacity. For example, if
the “XXX” amount equals 1400 lbs.
and there will be five 150 lb pas-
sengers in your vehicle, the
amount of available cargo and lug-
gage load capacity is 650 lbs.
(1400-750 (5 x 150) = 650 lbs.)

5.Determine the combined weight of

luggage and cargo being loaded
on the vehicle. That weight may not
safely exceed the available cargo
and luggage load capacity calcu-
lated in Step 4.

6.If your vehicle will be towing a trail-

er, load from your trailer will be
transferred to your vehicle. Consult
this manual to determine how this
reduces the available cargo and
luggage load capacity of your vehi-
cle.

UMA PE USA 5.QXP 12/22/2017 3:41 PM Page 137

Driving your vehicle

138

5

Refer to your vehicle’s tire and loading information label for specific information about your vehicle's capacity weight
and seating positions. The combined weight of the driver, passengers and cargo should never exceed your vehicle's
capacity weight.

C190F01JM

Item

Description

Total

A

Vehicle Capacity 1400 lbs

Weight

(635 kg)

Subtract Occupant

B

Weight

300 lbs

150 lbs (68 kg) × 2

(136 kg)

C

Available Cargo and 1100 lbs

Luggage weight

(499 kg)

Example 1

A

B

C

C190F02JM

Item

Description

Total

A

Vehicle Capacity 1400 lbs

Weight

(635 kg)

Subtract Occupant

B

Weight

750 lbs

150 lbs (68 kg) × 5

(340 kg)

C

Available Cargo and

650 lbs

Luggage weight

(295 kg)

A

B

C

Example 2

C190F03JM

Item

Description

Total

A

Vehicle Capacity 1400 lbs

Weight

(635 kg)

Subtract Occupant

B

Weight

860 lbs

172 lbs (78 kg) × 5

(390 kg)

C

Available Cargo and

540 lbs

Luggage weight

(245 kg)

A

B

C

Example 3

UMA PE USA 5.QXP 12/22/2017 3:41 PM Page 138

5 139

Driving your vehicle

Certification label

The certification label is located on
the driver's door sill at the center pil-
lar.
This label shows the maximum
allowable weight of the fully loaded
vehicle. This is called the GVWR
(Gross Vehicle Weight Rating). The
GVWR includes the weight of the
vehicle, all occupants, fuel and
cargo.
This label also tells you the maxi-
mum weight that can be supported
by the front and rear axles, called
Gross Axle Weight Rating (GAWR).

To find out the actual loads on your
front and rear axles, you need to go
to a weigh station and weigh your
vehicle.Your dealer can help you with
this. Be sure to spread out your load
equally on both sides of the center-
line.

The label will help you decide how
much cargo and installed equipment
your vehicle can carry.

If you carry items inside your vehicle
- like suitcases, tools, packages, or
anything else - they are moving as
fast as the vehicle. If you have to stop
or turn quickly, or if there is a crash,
the items will keep going and can
cause an injury if they strike the driv-
er or a passenger.

OEN056020

WARNING

- Over loading

Never exceed the GVWR for
your vehicle, the GAWR for
either the front or rear axle and
vehicle capacity weight.
Exceeding these ratings can
affect your vehicle’s handling
and braking ability.

UMA PE USA 5.QXP 12/22/2017 3:41 PM Page 139

Driving your vehicle

140

5

✽

✽

NOTICE

Overloading your vehicle may cause
damage. Repairs would not be cov-
ered by your warranty. Do not over-
load your vehicle.

WARNING

- Loose cargo

Do not travel with unsecured
blunt objects in the passenger
compartment of your vehicle
(e.g. suit cases or unsecured
child seats). These items may
strike occupant during a sud-
den stop or crash.

WARNING

- Over loading

Do not overload your vehicle.
Overloading your vehicle can
cause heat buildup in your vehi-
cle's tires and possible tire fail-
ure, increased stopping dis-
tances and poor vehicle han-
dling all of which may result in a
crash.

UMA PE USA 5.QXP 12/22/2017 3:41 PM Page 140

5 141

Driving your vehicle

This section will guide you in the
proper loading of your vehicle and/or
trailer, to keep your loaded vehicle
weight within its design rating capa-
bility, with or without a trailer.
Properly loading your vehicle will
provide maximum return of the vehi-
cle design performance. Before load-
ing your vehicle, familiarize yourself
with the following terms for determin-
ing your vehicle's weight ratings, with
or without a trailer, from the vehicle's
specifications and the certification
label:

Base curb weight

This is the weight of the vehicle
including a full tank of fuel and all
standard equipment. It does not
include passengers, cargo, or option-
al equipment.

Vehicle curb weight

This is the weight of your new vehicle
when you picked it up from your deal-
er plus any aftermarket equipment.

Cargo weight

This figure includes all weight added
to the Base Curb Weight, including
cargo and optional equipment.

GAW (Gross axle weight)

This is the total weight placed on
each axle (front and rear) - including
vehicle curb weight and all payload.

GAWR
(Gross axle weight rating)

This is the maximum allowable
weight that can be carried by a single
axle (front or rear). These numbers
are shown on the certification label.
The total load on each axle must
never exceed its GAWR.

GVW (Gross vehicle weight)

This is the Base Curb Weight plus
actual Cargo Weight plus passen-
gers.

GVWR
(Gross vehicle weight rating)

This is the maximum allowable
weight of the fully loaded vehicle
(including all options, equipment,
passengers and cargo). The GVWR
is shown on the certification label
located on the driver’s door sill.

VEHICLE WEIGHT GLOSSARY

UMA PE USA 5.QXP 12/22/2017 3:41 PM Page 141

What to do in an emergency

Road warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

• Hazard warning flashers . . . . . . . . . . . . . . . . . . . . . . . 6-2

In case of an emergency while driving. . . . . . . . . . 6-3

• If the engine stalls at a crossroad or crossing. . . . . . . 6-3
• If you have a flat tire while driving . . . . . . . . . . . . . . . 6-3
• If the engine stalls while driving . . . . . . . . . . . . . . . . . 6-3

If the engine will not start . . . . . . . . . . . . . . . . . . . . 6-4

• If engine doesn't turn over or turns over slowly . . . . 6-4
• If engine turns over normally but does not start . . . . 6-4

Emergency starting . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

• Jump starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
• Push-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

If the engine overheats. . . . . . . . . . . . . . . . . . . . . . . 6-8
Tire Pressure Monitoring System (TPMS) . . . . . . 6-9

• Check tire pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
• Low tire pressure telltale . . . . . . . . . . . . . . . . . . . . . . 6-11
• Low tire pressure position telltale . . . . . . . . . . . . . . . 6-11
• Changing a tire with TPMS . . . . . . . . . . . . . . . . . . . . 6-13
• This device complies with Part 15 of the

FCC rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15

If you have a flat tire . . . . . . . . . . . . . . . . . . . . . . . 6-16

• Jack and tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
• Removing and storing the spare tire . . . . . . . . . . . . . 6-17
• Changing tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19

Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26

• Towing service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26

6

UMA PE USA 6.qxp 12/20/2017 11:50 AM Page 1

What to do in an emergency

2

6

ROAD WARNING

Hazard warning flashers

The hazard warning flashers serves
as a warning to other drivers to exer-
cise extreme caution when
approaching, overtaking, or passing
your vehicle.

It should be used whenever emer-
gency repairs are being made or
when the vehicle is stopped near the
edge of a roadway.
Depress the flashers switch with the
ignition switch in any position. The
flashers switch is located in the cen-
ter facia panel. All turn signal lights
will flash simultaneously.

• The hazard warning flashers oper-

ates whether your vehicle is run-
ning or not.

• The turn signals do not work when

the hazard flashers is on.

• Care must be taken when using

the hazard warning flashers while
the vehicle is being towed.

OUMA048542

UMA PE USA 6.qxp 12/20/2017 11:50 AM Page 2

6 3

What to do in an emergency

If the engine stalls at a cross-
road or crossing

If the engine stalls at a crossroad or
crossing, set the shift lever in the N
(Neutral) position and then push the
vehicle to a safe place.

If you have a flat tire while
driving

If a tire goes flat while you are driv-
ing:
1. Take your foot off the accelerator

pedal and let the vehicle slow
down while driving straight ahead.
Do not apply the brakes immedi-
ately or attempt to pull off the road
as this may cause a loss of con-
trol. When the vehicle has slowed
to such a speed that it is safe to do
so, brake carefully and pull off the
road. Drive off the road as far as
possible and park on a firm level
ground. If you are on a divided
highway, do not park in the median
area between the two traffic lanes.

2. When the vehicle is stopped, turn

on your emergency hazard flash-
ers, set the parking brake and put
the transmission in P (Park).

3. Have all passengers get out of the

vehicle. Be sure they all get out on
the side of the vehicle that is away
from traffic.

4. When changing a flat tire, follow

the instruction provided later in
this section.

If the engine stalls while driv-
ing

1. Reduce your speed gradually,

keeping a straight line. Move cau-
tiously off the road to a safe place.

2. Turn on your emergency flashers.
3. Try to start the engine again. If

your vehicle will not start, contact
an authorized Kia dealer or seek
other qualified assistance.

✽

✽

NOTICE

If there was a check engine light and
loss of power or stall and if safe to do
so, wait at least 10 seconds to restart
the vehicle after it stalls. This may
reset the car so it will no longer run
at low power condition.

IN CASE OF AN EMERGENCY WHILE DRIVING

UMA PE USA 6.qxp 12/20/2017 11:50 AM Page 3

What to do in an emergency

4

6

IF THE ENGINE WILL NOT START

If engine doesn't turn over or
turns over slowly

1. Be sure the shift lever is in N

(Neutral) or P (Park) and the
emergency brake is set.

2. Check the battery connections to

be sure they are clean and tight.

3. Turn on the interior light. If the light

dims or goes out when you oper-
ate the starter, the battery is dis-
charged.

4. Check the starter connections to

be sure they are securely tight-
ened.

5. Do not push or pull the vehicle to

start it. See instructions for "Jump
starting".

If engine turns over normally
but does not start

1. Check the fuel level.
2. With the ignition switch in the

LOCK position, check all connec-
tors at the ignition coils and spark
plugs. Reconnect any that may be
disconnected or loose.

3. Check the fuel line in the engine

compartment.

4. If the engine still does not start,

call an authorized Kia dealer or
seek other qualified assistance.

WARNING

- Push/

Pull start

Do not push or pull the vehicle
to start it. Push or pull starting
may cause the catalytic con-
verter to overload and create a
fire hazard.

UMA PE USA 6.qxp 12/20/2017 11:50 AM Page 4

6 5

What to do in an emergency

EMERGENCY STARTING

Connect cables in numerical order
and disconnect in reverse order.

Jump starting

Jump starting can be dangerous if
done incorrectly. Therefore, to avoid
harm to yourself or damage to your
vehicle or battery, follow these jump
starting procedures. If in doubt, we
strongly recommend that you have a
competent technician or towing serv-
ice jump start your vehicle.

CAUTION

- Push/Pull start

to 12 Volt Battery

Use only a 12-volt jumper sys-
tem. You can damage a 12-volt
starting motor, ignition system,
and other electrical parts
beyond repair by use of a 24-
volt power supply (either two
12-volt batteries in series or a
24-volt motor generator set).

WARNING

- Battery

Never attempt to check the elec-
trolyte level of the battery as
this may cause the battery to
rupture or explode.

WARNING

- Frozen

batteries

Do not attempt to jump start the
vehicle if the discharged battery
is frozen or if the electrolyte
level is low as the battery may
rupture or explode.

OUM068046L

UMA PE USA 6.qxp 12/20/2017 11:50 AM Page 5

What to do in an emergency

6

6

Jump starting procedure

1.Make sure the booster battery is

12-volt and that its negative termi-
nal is grounded.

2.If the booster battery is in another

vehicle, do not allow the vehicles to
come in contact.

3.Turn off all unnecessary electrical

loads.

4.Connect the jumper cables in the

exact sequence shown in the illus-
tration. First connect one end of a
jumper cable to the positive termi-
nal of the discharged battery (1),
then connect the other end to the
positive terminal of the booster
battery (2).
Proceed to connect one end of the
other jumper cable to the negative
terminal of the booster battery (3),
then the other end to a solid, sta-
tionary, metallic point (for example,
the engine lifting bracket) away
from the battery (4). Do not con-
nect it to or near any part that
moves when the engine is cranked.

Do not allow the jumper cables to
contact anything except the correct
battery terminals or the correct
ground. Do not lean over the bat-
tery when making connections.

WARNING

- Sulfuric acid

risk

When jump starting your vehicle
be careful not to get acid on
yourself, your clothing or on the
vehicle. Automobile batteries
contain sulfuric acid. This is poi-
sonous and highly corrosive.

WARNING

- Battery

Keep all flames or sparks away
from the battery. The battery
produces hydrogen gas which
will explode if exposed to flame
or sparks.

WARNING

- Battery

cables

Do not connect the jumper cable
from the negative terminal of the
booster battery to the negative
terminal of the discharged bat-
tery. This can cause the dis-
charged battery to overheat and
crack, releasing battery acid.
Make sure to connect one end of
the jumper cable to the negative
terminal of the booster battery,
and the other end to a metalic
point, far away from the battery.

UMA PE USA 6.qxp 12/20/2017 11:50 AM Page 6

6 7

What to do in an emergency

5.Start the engine of the vehicle with

the booster battery and let it run at
2,000 rpm, then start the engine of
the vehicle with the discharged
battery.

If the cause of your battery discharg-
ing is not apparent, you should have
your vehicle checked by an author-
ized Kia dealer.

Push-starting

Vehicles equipped with automatic
transmission lock system cannot be
push-started.
Follow the directions in this section
for jump-starting.

WARNING

- Tow starting

vehicle

Never tow a vehicle to start it
because the sudden surge for-
ward when the engine starts
could cause a collision with the
tow vehicle.

UMA PE USA 6.qxp 12/20/2017 11:50 AM Page 7