KIA Rondo (2017 year). Instruction — part 34
Maintenance
Engine compartment fuse panel
OGD071023
✽ NOTICE
The actual fuse/relay panel label
may differ depending on equip-
ment/options.
ORP076086N
8 73
Maintenance
Instrument panel (Driver’s side fuse panel)
No.
Fuse rating
Description
Protected component
1
10A
PDM 2
Start/Stop Button Switch, Immobilizer Module
2
15A
MULTI MEDIA
DC-DC Converter (Audio), A/V & Navigation Head Unit, Audio
Seat Warmer Control Module, Rear Seat Warmer Module, Passenger Seat Warmer Module, DC-DC
Converter (AMP), Auto Head Lamp Leveling Device Module, Rain Sensor, Head Lamp Leveling Device
3
7.5A
MODULE 3
Actuator LH/RH, A/C Control Module, Electro Chromic Mirror, Head Lamp Leveling Device Switch, A/V
Navigation Head Unit
4
7.5A
CLUSTER
Instrument Cluster, DC-DC Converter (Audio)
5
7.5A
MDPS
MDPS Unit
ICM Relay Box (B/Alarm Relay), Ignition Lock Switch
6
7.5A
START
[A/T - Transaxle Range Switch], [M/T - E/R Junction Block
(RLY. 10), ECM/PCM, Smart Key Control Module]
Driver/Passenger Power Outside Mirror, Driver/Passenger Foot Lamp, Ignition Key ILL. & Door Warning
INTERIOR
7
10A
Switch, Overhead Console Lamp, Room Lamp, Vanity Lamp LH/RH, Rear Personal Lamp LH/RH,
LAMP
Luggage Lamp, Portable Lamp
8
20A
PDM
Smart Key Control Module
9
7.5A
MEMORY 2
RF Receiver
Smart Key Control Module, Immobilizer Module,
10
10A
ECU
Vehicle Speed Sensor, ECM/PCM, Air Flow Sensor (D4FD), Glow Relay Unit
11
10A
ABS
ABS/ESC Control Module
8 74
Maintenance
No.
Fuse rating
Description
Protected component
12
15A
TCU
TCM (D4FD), Transaxle Range Switch (A/T, DCT), E/R Junction Block (Fuse - F27) (M/T)
13
7.5A
MODULE 4
BCM
14
7.5A
A/CON SW
A/C Control Module
Instrument Cluster, Auto Light & Photo Sensor, Tire Pressure Monitoring Module, Ultrasonic Instrusion
15
10A
MEMORY 1
Protection Sensor, A/C Control Module, Data Link Connector, Siren Control Module, Clock, BCM
Smart Parking Assist Control Module, Stop Lamp Switch, Tire Pressure Monitoring Module, Clutch Sensor
(M/T), Front Parking Assist Sensor (Center)/(Side) LH/RH, Front Parking Assist Sensor (In)/(Out) LH/RH,
16
7.5A
MODULE 1
Rear Parking Assist Sensor Center LH/RH, Crash Pad Switch, Rear Parking Assist Sensor (In)/(Out)
LH/RH, Sport Mode Switch, Parking Assist Buzzer, Multipurpose Check Connector, Electric Parking Brake
Module, Lane Departure Warning Module, Blind Spot Detection Radar LH/RH
POWER
17
20A
Rear Power Outlet, Cigarette Lighter, Front Power Outlet
OUTLET 1
A/V & Navigation Head Unit, DC-DC Converter (Audio/AMP), Audio, Clock, Smart Key Control Module,
18
10A
MODULE 6
BCM, E/R Junction Block (RLY. 7), AMP, Power Outside Mirror Switch
SBR Control Module, Seat Belt Reminder IND.,Instrument Cluster Door Lock & PAB On/Off IND., SRS
19
15A
A/BAG
Control Module, A/C Control Module
Rear Safety Power Window Module LH, Driver/Passenger Safety Power Window Module, Power Window
20
25A
P/WDW LH
LH Relay
21
10A
HTD MIRR
A/C Control Module, ECM/PCM, Driver/Passenger Power Outside Mirror
Portable Lamp, Rear Seat Warmer Module, Panorama Sunroof Assembly, Driver/Passenger CCS Control
22
7.5A
MODULE 5
Module, Seat Warmer Control Module, Passenger Seat Warmer Module, E/R Junction Block (RLY. 8)
23
7.5A
MODULE 7
BCM, Smart Key Control Module
8 75
Maintenance
No.
Fuse rating
Description
Protected component
24
15A
HTD STRG
Steering Wheel Heater
25
15A
S/HEATER RR
Rear Seat Warmer Module
26
25A
AMP
DC-DC Converter (AMP), AMP
27
20A
SUNROOF
Panorama Sunroof Assembly
S/HEATER
28
20A
Driver/Passenger CCS Control Module, Seat Warmer Control Module, Passenger Seat Warmer Module
FRT
ICM Relay Box (Turn Signal Lamp Sound Relay, Folding/Unfolding Relay), Key Solenoid, Sport Mode
29
7.5A
MODULE 2
Switch, Console Switch LH/RH, Rear Power Window Switch LH/RH
30
7.5A
A/CON
Diesel Block (RLY. 2, RLY. 3), E/R Junction Block (RLY. 2), A/C Control Module, Cluster Ionizer
31
15A
WIPER
Rear Wiper Motor, ICM Relay Box (Rear Wiper Relay), Multifunction Switch
Rear Safety Power Window Module RH, Driver/Passenger Safety Power Window Module, Power Window
32
25A
P/WDW RH
RH Relay
33
30A
P/SEAT DRV
Driver Seat Manual Switch
FOG LAMP
34
10A
ICM Relay Box (Rear Fog Lamp Relay)
RR
35
20A
DR LOCK
Tail Gate Open Relay, Door Lock/Unlock Relay, ICM Relay Box (Dead Lock Relay)
8 76
Maintenance
Engine compartment main fuse panel
Fuse
Fuse rating
Description
Protected component
80A
MDPS
MDPS Unit
60A
B+1
Smart Junction Block (IPS 1, IPS 2, IPS 3, IPS 4, Fuse - F2/F9/F22/F29/F36)
40A
IG2
RLY. 10 (Start Relay), Ignition Switch (W/O Button Start), RLY. 3 (PDM 3 (IG2) Relay, With Button Start)
40A
ABS 1
ABS/ESC Control Module
MULTI
FUSE
40A
RR HTD
RLY. 6 (Rear Defogger Relay)
40A
BLOWER
RLY. 2 (Blower Relay)
40A
ABS 2
ABS/ESC Control Module, Multipurpose Check Connector
60A
B+2
Smart Junction Block (IPS 5, IPS 6, IPS 7, IPS 8, Fuse - F31/F37/F38)
50A
B+4
E/R Junction Block (Fuse - F29/F30/F31)
30A
EPB 1
Electric Parking Brake Module
FUSE
50A
C/FAN
RLY. 1 (C/Fan 1 Relay), RLY. 5 (C/Fan 2 Relay)
30A
EPB 2
Electric Parking Brake Module
8 77
Maintenance
Fuse
Fuse rating
Description
Protected component
20A
H/LP WASHER
RLY. 8 (Head Lamp Washer Relay)
10A
BRAKE SWITCH
Stop Lamp Switch, Smart Key Control Module
30A
POWER OUTLET 2
RLY. 7 (Power Outlet Relay)
15A
FUEL PUMP
RLY. 12 (Fuel Pump Relay)
15A
DEICER
RLY. 4 (Deicer Relay)
15A
STOP LAMP
Stop Signal Electronic Module
50A
B+3
Smart Junction Block (Leak Current Autocut Device, Fuse - F30/F32/F33/F39)
FUSE
40A
IG1
RLY. 9 (PDM 1 (ACC) Relay), RLY. 11 (PDM 2 (IG 1) Relay), Ignition Switch
40A
ECU 5
EMS Block (Fuse - F32/F33/F34, Engine Control Relay)
MT - Back-Up Lamp Switch,
10A
B/UP LP
A/T - Rear Combination Lamp (In) LH/RH, Electro Chromic Mirror, A/V & Navigation Head Unit,
Audio, Instrument Cluster
25A
WIPER (LH)
Front Wiper Motor LH
25A
WIPER (RH)
Front Wiper Motor RH
15A
ECU 4
ECM/PCM
8 78
Maintenance
Fuse
Fuse rating
Description
Protected component
15A
HORN
Horn Relay
15A
ECU 3
PCM (A/T), ECM (M/T)
10A
B/ALARM
B/Alarm Horn Relay, Horn Relay
10A
INJECTOR
G4NA : Injector #1/#2/#3/#4
G4FD : PCM (A/T), ECM (M/T)
10A
ECU 2
FUSE
G4NC : PCM (A/T), ECM (M/T)
20A
IGN COIL 1
Ignition Coil #1/#2/#3/#4, Condenser
G4FD : Oil Control Valve #1/ #2, Oil Level Sensor, E/R Junction Block (RLY. 1, RLY. 5)
10A
SENSOR 2
G4NA/G4NC : Oil Control Valve #1/ #2, Camshaft Position Sensor (Intake/Exhaust),
Oil Level Sensor (G4NC), E/R Junction Block (RLY. 1, RLY. 5)
20A
ECU 1
PCM (A/T), ECM (M/T)
10A
SENSOR 1
Oxygen Sensor (Up/Down), Variable Intake Solenoid Valve, Purge Control Solenoid Valve
8 79
Maintenance
Relay Name
Type
C/FAN 1 RELAY
Plug Micro
BLOWER RELAY
Plug Micro
PDM3 (IG2) Relay
Plug Micro
Deicer Relay
Plug Micro
C/Fan 2 Relay
Plug Micro
RR HTD Relay
Plug Micro
Power Outlet Relay
Plug Micro
H/Lamp Washer Relay
Plug Micro
PDM1 (ACC) RELAY
Plug Micro
START RELAY
Plug Micro
PDM2 (IG1) Relay
Plug Micro
Fuel Pump Relay
Plug Micro
Engine Control Relay
PCB
B/Alarm Horn Relay
PCB
Horn Relay
PCB
8 80
Maintenance
LIGHT BULBS
✽ NOTICE
WARNING - Working on
CAUTION
After driving in heavy rain or wash-
the lights
If you do not have necessary
ing the vehicle, headlight and tail-
Prior to working on the light,
tools, the correct bulbs and the
light lenses could appear foggy. This
firmly apply the parking brake,
expertise, we recommend that
condition is caused by the tempera-
ensure that the ignition switch
you consult an authorized Kia
ture difference between the lamp
is turned to the “LOCK” position
dealer. In many cases, it is diffi-
inside and outside. This is similar to
(smart key: turn off the engine)
cult to replace vehicle light
the condensation on your windows
and turn off the lights to avoid
bulbs because other parts of the
inside your vehicle during rain and
sudden movement of the vehi-
vehicle must be removed before
does not indicate a problem with
cle and burning your fingers or
you can get to the bulb. This is
your vehicle. If the water leaks into
getting an electric shock.
especially true if you have to
the lamp bulb circuitry, we recom-
remove the headlight assembly
mend that the system be checked by
to get to the bulb(s).
an authorized Kia dealer.
Use only the bulbs of the specified
Removing/installing the head-
wattage.
light assembly can result in
damage to the vehicle.
CAUTION
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause damage to the fuse
or electric wiring system.
8 81
Maintenance
Front light replacement
1. Turn off the engine and open the
Headlight (Low, High Non-HID Type)
hood.
2. Disconnect the power connector
front the back of the headlight
assembly.
ORP076087N
ORP072059
(1) Headlight(High)
Follow the steps 1 to 2 from the pre-
vious chapter.
(2) Headlight(Low)
3. Remove the headlight bulb cover
(3) Position/Turn signal light
by turning it counterclockwise.
(4) DRL(Daytime running light,Bulb
4. Remove the socket from the
or LED(if equipped))
assembly by turning the socket
(5) Side marker light
counterclockwise until the tabs on
(6) Front fog light(if equipped)
the socket align with the slots on
the assembly.
5. Pull the bulb out of the socket.
6. Insert a new bulb into the socket.
8 82
Maintenance
7. Install the socket in the assembly
Headlight (Low, HID type),
✽ NOTICE
by aligning the tabs on the socket
DRL (LED type)
HID lamps have superior perform-
with the slots in the assembly.
If the DRL lamp
(LED) does not
ance vs. halogen bulbs. HID lamps
Push the socket into the assembly
operate, have the vehicle checked by
are estimated by the manufacturer to
and turn the socket clockwise.
an authorized Kia dealer.
last twice as long or longer than halo-
8. Install the headlight bulb cover by
gen bulbs depending on their fre-
LED lamps do not have replaceable
turning it clockwise.
quency of use. They will probably
bulbs.
9. Connect the power connector to
require replacement at some point in
A skilled technician should check or
the back of the headlight assem-
the life of the vehicle. Cycling the
repair the Headlight low (HID) and
bly.
headlamps on and off more than typ-
DRL lamp(LED), for it may damage
ical use will shorten HID lamps life.
related parts of the vehicle.
HID lamps do not fail in the same
✽ NOTICE
manner as halogen incandescent
If the headlight aiming adjustment
WARNING - HID
lamps. If a headlamp goes out after a
is necessary after the headlight
Headlight low beam
period of operation but will immedi-
assembly is reinstalled, have the
(if equipped)
ately relight when the headlamp
vehicle checked by an authorized
switch is cycled it is likely the HID
Do not attempt to replace or
Kia dealer.
lamp needs to be replaced. HID light-
inspect the low beam (XENON
ing components are more complex
bulb) due to electric shock dan-
than conventional halogen bulbs thus
ger. If the low beam
(XENON
have higher replacement cost.
bulb) is not working, have the
vehicle checked by an author-
ized Kia dealer.
8 83
Maintenance
Position/Turn signal light
(Continued)
A bulb should be operated
only when installed in a head-
light.
•
If a bulb is damaged or
cracked, replace it immediate-
ly and carefully dispose of it.
•
Wear eye protection when
changing a bulb. Allow the
bulb to cool down before han-
OHD076046
dling it.
ORP072050
WARNING - Halogen
Follow the steps 1 to 2 from the pre-
bulbs
vious page.
•
Halogen bulbs contain pres-
3. Remove the socket from the
surized gas that will produce
assembly by turning the socket
flying pieces of glass if broken.
counterclockwise until the tabs on
•
Always handle them carefully,
the socket align with the slots on
and avoid scratches and abra-
the assembly.
sions. If the bulbs are lit, avoid
4. Remove the bulb from the socket
contact with liquids. Never
by pressing it in and rotating it
touch the glass with bare
counterclockwise until the tabs on
hands. Residual oil may cause
the bulb align with the slots in the
the bulb to overheat and burst
socket. Pull the bulb out of the
when lit.
socket.
(Continued)
8 84
Maintenance
5. Insert a new bulb by inserting it
Front fog light (if equipped)
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
ORP072063
4. Remove the bulb-socket from the
OJD072050
housing by turning the socket
1. Pull the wheel guard down by
counter clockwise until the tabs on
rotating the screws.
the socket align with the slots on
2. Reach your hand into the back of
the housing.
the front bumper.
5. Install the new bulb-socket into the
3. Disconnect the power connector
housing by aligning the tabs on
from the socket.
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock-
wise.
6. Connect the power connector to
the socket.
8 85
Maintenance
Side repeater light bulb
Rear combination light bulb
(5) Rear turn signal light
replacement
replacement
(6) Side marker light
■ Type A
ORP076088N
■ Type B
ORP072035
If the light bulb does not operate, we
recommend that the system be
checked by an authorized Kia dealer.
ORP076089N
(1) Tail light
(2) Tail / Stop light
(3) Turn signal light
(4) Back up light
8 86
Maintenance
Outside light
8. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Reinstall the light assembly to the
body of the vehicle.
Stop and tail light or tail light
(LED type)
ORP072039
If the Stop and tail lamp or tail lamp
(LED) do not operate, have the vehi-
5. Remove the socket from the
ORP072038
cle checked by an authorized Kia
assembly by turning the socket
dealer.
❈ The actual rear combination lamp shape in
counterclockwise until the tabs on
the vehicle may differ from illustration.
the socket align with the slots on
LED lamps do not have replaceable
bulbs.
the assembly.
Rear turn signal light and stop/tail
A skilled technician should check or
6. Remove the bulb from the socket
light
repair Stop and tail lamp or tail lamp
by pressing it in and rotating it
(LED), for it may damage related
1. Turn off the engine.
counterclockwise until the tabs on
parts of the vehicle.
the bulb align with the slots in the
2. Open the tailgate.
socket. Pull the bulb out of the
3. Loosen the light assembly retain-
socket.
ing screws with a cross-tip screw-
7. Insert a new bulb by inserting it
driver.
into the socket and rotating it until
4. Remove the rear combination light
it locks into place.
assembly from the body of the
vehicle.
8 87
Maintenance
Inside light
6. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
7. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
8. Install the service cover by putting
it into the service hole.
ORP072042
Tail light/Back-up light (Bulb type)
ORP072040
4. Remove the socket from the
1. Turn off the engine.
assembly by turning the socket
2. Open the tailgate.
counterclockwise until the tabs on
3. Remove the service cover using a
the socket align with the slots on
flat-blade screwdriver.
the assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket. (Back-up lamp : Remove
the bulb from the socket by pulling
it out)
8 88
Maintenance
High mounted stop light bulb
License plate light bulb
5. Install a new bulb.
replacement
replacement
6. Reinstall the lens securely with the
lens retaining screws.
ORP072043
ORP076080L
If the light does not operate, have the
1. Remove the lens retaining screws
vehicle checked by an authorized Kia
with a philips head screwdriver.
dealer.
2. Remove the socket from the
LED lamps do not have replaceable
assembly by turning the socket
bulbs.
conterclockwise.
A skilled technician should check or
3. Remove the bulb by pulling it
repair the high mounted stop lamp
straight out.
(LED), for it may damage related
4. Install the socket into the assembly
parts of the vehicle.
by aligning the tabs on the socket
with the slots on the assembly and
turning the socket clockwise.
8 89
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст