KIA Magentis (2010 year). Instruction — part 8
Features of your vehicle
CAUTION
•
Never place anything over sensor
(1) located on the instrument
panel. This will ensure better
auto-light system control.
•
Don’t clean the sensor using a
window cleaner. The cleaner may
leave a light film which could
interfere with sensor operation.
•
If your vehicle has window tint or
other types of coating on the
OUN020222
OUN020223
front windshield, the Auto light
D190402ABH
D190403AUN
system may not work properly.
Headlight position (
)
Auto light position (if equipped)
When the light switch is in the headlight
When the light switch is in the AUTO light
position
(2nd position), the head, tail,
position, the taillights and headlights will
license and instrument panel lights are
be turned ON or OFF automatically
ON.
depending on the amount of light outside
the vehicle.
✽ NOTICE
The ignition switch must be in the ON
position to turn on the headlights.
4 63
Features of your vehicle
OUN020225
OUN020224
OUN020226
D190500AUN
To flash the headlights, pull the lever
D190600AUN
High beam operation
towards you. It will return to the normal
Turn signals and lane change sig-
(low beam) position when released. The
nals
To turn on the high beam headlights,
headlight switch does not need to be on
push the lever away from you. Pull it back
The ignition switch must be on for the
to use this flashing feature.
for low beams.
turn signals to function. To turn on the
The high beam indicator will light when
turn signals, move the lever up or down
the headlight high beams are switched
(A). Green arrow indicators on the instru-
on.
ment panel indicate which turn signal is
To prevent the battery from being dis-
operating. They will self-cancel after a
charged, do not leave the lights on for a
turn is completed. If the indicator contin-
prolonged time while the engine is not
ues to flash after a turn, manually return
running.
the lever to the OFF position.
4 64
Features of your vehicle
To signal a lane change, move the turn
D190900AUN-EC
signal lever slightly and hold it in position
Daytime running light
(B). The lever will return to the OFF posi-
(if equipped)
tion when released.
Daytime Running Lights (DRL) can make
If an indicator stays on and does not
it easier for others to see the front of your
flash or if it flashes abnormally, one of the
vehicle during the day. DRL can be help-
turn signal bulbs may be burned out and
ful in many different driving conditions,
will require replacement.
and it is especially helpful after dawn and
before sunset.
✽ NOTICE
The DRL system will make the head-
If an indicator flash is abnormally quick
lights turn OFF when:
or slow, a bulb may be burned out or
1. The headlight switch is ON.
OUN020219
have a poor electrical connection in the
2. The parking brake is applied.
D190700AHD-EU
circuit.
3. Engine stops.
Front fog light (if equipped)
Fog lights are used to provide improved
visibility and avoid accidents when visibil-
ity is poor due to fog, rain or snow etc.
The fog lights will turn on when fog light
switch (1) is turned to ON after the head-
lights are turned on.
To turn off the fog lights, turn the switch
to OFF.
CAUTION
When in operation, the fog lights
consume large amounts of vehicle
electrical power. Only use the fog
lights when visibility is poor or
unnecessary battery and generator
drain could occur.
4 65
Features of your vehicle
WIPERS AND WASHERS
✽ NOTICE
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about
10 minutes, or
until the snow and/or ice is removed
INT*
INT*
before using the windshield wipers to
(AUTO)
(AUTO)
ensure proper operation.
✽ NOTICE
•
When you operate the wipers, if your
vehicle has a problem in any part of
the wiper operation system, the wiper
OUN020301
OUN020304
may operate in the LO mode regard-
A : Wiper speed control
D200100AMG-EU
less of the wiper switch position. In
· MIST - Single wipe
Windshield wipers
this case, have your vehicle checked
· OFF - Off
Operates as follows when the ignition
by an authorized KIA dealer as soon
· INT - Intermittent wipe
switch is turned ON.
as possible.
•
When the ignition key is removed, the
AUTO - AUTO control wipe
MIST : For a single wiping cycle, push
wiper blade sometimes may move
(if equipped)
the lever upward and release it
with the lever in the OFF position.
slightly to be properly positioned for
· LO - Low wiper speed
The wipers will operate continu-
reducing the deterioration of the
· HI - High wiper speed
ously if the lever is pushed
windshield wipers.
upward and held.
B : Intermittent or Auto control wipe
time adjustment
OFF : Wiper is not in operation
INT : Wiper operates intermittently at
C : Wash with brief wipes
the same wiping intervals. Use this
mode in a light rain or mist. To vary
the speed setting, turn the speed
control knob (1).
LO
: Normal wiper speed
HI
: Fast wiper speed
4 66
Features of your vehicle
If the ignition switch is turned ON when
the wiper switch is set in AUTO mode, or
CAUTION
the wiper switch is set in AUTO mode
When washing the vehicle, set the
when the ignition switch is ON, or the
wiper switch in the OFF position to
speed control knob is turned upward
stop the auto wiper operation.
when the wiper switch is in AUTO mode,
The wiper may operate and be dam-
the wiper will operate once to perform a
aged if the switch is set in the AUTO
self-check of the system. Set the wiper to
mode while washing the vehicle.
OFF position when the wiper is not in
Do not remove the sensor cover
use.
located on the upper end of the pas-
Sensor
senger side windshield glass.
CAUTION
Damage to system parts could
ONF048067
occur and may not be covered by
When the ignition switch is ON and
D200101AMG
your vehicle warranty.
the windshield wiper switch is
Auto control (if equipped)
placed in the AUTO mode, use cau-
When starting the vehicle in winter,
The rain sensor located on the upper end
tion in the following situations to
set the wiper switch in the OFF
of the windshield glass senses the
avoid any injury to the hands or
position. Otherwise, wipers may
amount of rainfall and controls the wiping
other parts of the body:
operate and ice may damage the
cycle for the proper interval. The more it
windshield wiper blades. Always
• Do not touch the upper end of the
rains, the faster the wiper operates. When
windshield glass facing the rain
remove all snow and ice and defrost
the rain stops, the wiper stops. To vary the
sensor.
the windshield properly prior to
speed setting, turn the speed control
operating the windshield wipers.
• Do not wipe the upper end of the
knob (1).
windshield glass with a damp or
wet cloth.
• Do not put pressure on the wind-
shield glass.
4 67
Features of your vehicle
CAUTION
To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.
WARNING
Do not use the washer in freezing
temperatures without first warming
ONF048068
the windshield with the defrosters;
D200200AUN
the washer solution could freeze on
contact with the windshield and
Windshield washers
obscure your vision.
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
windshield and to run the wipers
1-3
cycles.
CAUTION
Use this function when the windshield is
• To prevent possible damage to
dirty.
the wipers or windshield, do not
The spray and wiper operation will con-
operate the wipers when the
tinue until you release the lever.
windshield is dry.
If the washer does not work, check the
• To prevent damage to the wiper
washer fluid level. If the fluid level is not
blades, do not use gasoline,
sufficient, you will need to add appropri-
kerosene, paint thinner, or other
ate non-abrasive windshield washer fluid
solvents on or near them.
to the washer reservoir.
• To prevent damage to the wiper
The reservoir filler neck is located in the
arms and other components, do
front of the engine compartment on the
not attempt to move the wipers
passenger side.
manually.
4 68
Features of your vehicle
INTERIOR LIGHT
D210000AEN
CAUTION
Do not use the interior lights for
extended periods when the engine
is not running.
It may cause battery discharge.
OMG030076
OMG030076-1
D210100ANF
Mood lamp
Map lamp
The mood lamp comes on when the igni-
•
: Push the switch to turn the
tion switch is in the ACC or ON position.
map lamp on or off. This light
produces a spot beam for con-
venient use as a map lamp at
night or as a personal lamp for
the driver and the front pas-
senger.
4 69
Features of your vehicle
• DOOR (3) :
In the DOOR position, the light comes on
when any door is opened regardless of
the ignition switch position.
When doors are unlocked by the trans-
mitter, the light comes on for approxi-
mately 30 seconds as long as any door is
not open. The light goes out gradually
after approximately
30 seconds if the
door is closed. However, if the ignition
switch is ON or all doors are locked, the
light will turn off immediately.
OMG049124
OMG035061
If a door is opened the light stays on for
D210200ANF
about 20 minutes. However, if a door is
D210300ABH
Dome lamp
opened with the ignition switch in the ON
Trunk room lamp
position, the light stays on continuously.
• ON (1) :
The trunk room lamp comes on when the
In the ON position, the light stays on at all
trunk is opened.
times.
CAUTION
Do not leave the switch in this posi-
tion for an extended period of time
when the vehicle is not running.
• OFF (2):
In the OFF position, the light stays off at
all times, even when a door is open.
4 70
Features of your vehicle
DEFROSTER
D220000AUN
CAUTION
To prevent damage to the conduc-
tors bonded to the inside surface of
the rear window, never use sharp
instruments or window cleaners
containing abrasives to clean the
window.
✽ NOTICE
OMG049069
OMG049111L
If you want to defrost and defog the
D210500ABH
D210600AUN
front windshield, refer to “Windshield
Glove box lamp (if equipped)
Vanity mirror lamp (if equipped)
defrosting and defogging” in this sec-
The glove box lamp comes on when the
Opening the lid of the vanity mirror will
tion.
glove box is opened.
automatically turn on the mirror light.
4 71
Features of your vehicle
Type A
The indicator on the rear window
defroster button illuminates when the
defroster is ON.
If there is heavy accumulation of snow on
the rear window, brush it off before oper-
ating the rear defroster.
The rear window defroster automatically
turns off after approximately 20 minutes
or when the ignition switch is turned off.
To turn off the defroster, press the rear
window defroster button again.
OMG049070
Type B
OMG045100
D220200AEN
Front windshield deicer
(if equipped)
If your vehicle is equipped with the front
windshield deicer, it will be operating at
the same time you operate the rear win-
dow defroster.
OMG049071
D220100AEN
Rear window defroster
The defroster heats the window to
remove frost, fog and thin ice from the
rear window, while the engine is running.
To activate the rear window defroster,
press the rear window defroster button
located in the center facia switch panel.
4 72
Features of your vehicle
MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)
1. Fan speed control knob
4. Temperature control knob
2. Air intake control button
5. Air conditioning button
3. Mode selection knob
(if equipped)
OMG049072
D230000ANF
4 73
Features of your vehicle
D230100AUN
Heating and air conditioning
1. Start the engine.
2. Set the mode to the desired position.
3. Set the temperature control to the
desired position.
4. Set the air intake control to the outside
(fresh) air position.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system (if equipped)
on.
OMG049073N
4 74
Features of your vehicle
MAX
MAX A/C-Level (B,D)
Floor/Defrost-Level (A, C, D)
A/C
Air is discharged through the face level
Most of the air flow is directed to the floor
vents.
and the windshield with a small amount
If the “MAX A/C” mode is selected, the
directed to the side window defrosters.
A/C will turn on automatically and
“Recirculation” mode will be activated.
Defrost-Level (A, D)
Face-Level (B,D)
Most of the air flow is directed to the
OMG049108
windshield with a small amount of air
Air flow is directed toward the upper body
directed to the side window defrosters.
D230101AMG
and face. Additionally, each outlet can be
Mode selection
controlled to direct the air discharged
The mode selection knob control the
from the outlet.
direction of the air flow through the venti-
lation system.
Air can be directed to the floor, dashboard
Bi-Level (B, D, C)
outlets, or windshield. Six symbols are used
to represent MAX A/C, Face, Bi-Level,
Floor, Floor-Defrost and Defrost air position.
Air flow is discharged towards the face
The MAX A/C mode is used to cool the
and floor.
inside of the vehicle faster.
Floor-Level (C, A, D)
Most of the air flow is directed to the
floor, with a small amount of the air being
directed to the windshield and side win-
dow defroster.
4 75
Features of your vehicle
OMG049075L
OMG049076
OMG049077
Instrument panel vents
D230102AFD
D230103AFD
The outlet port can be opened or closed
Temperature control
Air intake control
separately using the horizontal thumb-
The temperature control knob allows you
This is used to select outside (fresh) air
wheel. To close the vent, rotate it to the
to control the temperature of the air flow-
position or recirculated air position.
far left position. To open the vent, rotate it
ing from the ventilation system. To
To change the air intake control position,
right to the desired position.
change the air temperature in the pas-
push the control button.
Also, you can adjust the direction of air
senger compartment, turn the knob to
delivery from these vents using the vent
the right position for warm air or left posi-
control lever as shown.
tion for cooler air.
4 76
Features of your vehicle
Recirculated air position
✽ NOTICE
The indicator light on the but-
Prolonged operation of the heater in the
WARNING
ton is illuminated when the
recirculated air position
(without air
•
Continued used of the climate
recirculated air position is
conditioning selected) may cause fog-
control system operation in the
selected.
recirculated air position may
ging of the windshield and side windows
With the recirculated air posi-
and the air within the passenger com-
allow humidity to increase inside
tion selected, air from pas-
partment may become stale.
the vehicle which may fog the
senger compartment will be
In addition, prolonged use of the air
glass and obscure visibility.
drawn through the heating
conditioning with the recirculated air
•
Do not sleep in a vehicle with the
system and heated or cooled
position selected will result in excessive-
air conditioning or heating sys-
according to the function
ly dry air in the passenger compart-
tem on. It may cause serious
selected.
ment.
harm or death due to a drop in the
oxygen level and/or body temper-
Outside (fresh) air position
ature.
The indicator light on the but-
•
Continued used of the climate
ton is illuminated when the
control system operation in the
outside (fresh) air position is
recirculated air position can
selected.
cause drowsiness or sleepiness,
and loss of vehicle control. Set
With the outside (fresh) air
the air intake control to the out-
position selected, air enters
side (fresh) air position as much
the vehicle from outside and
as possible while driving.
is heated or cooled according
to the function selected.
4 77
Features of your vehicle
System operation
D230501AUN
Ventilation
1. Set the mode to the
position.
2. Set the air intake control to the outside
(fresh) air position.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
OMG049078
OMG049079
D230502AUN
D230104AUN
D230105AUN
Heating
Fan speed control
Air conditioning (if equipped)
1. Set the mode to the
position.
The ignition switch must be in the ON
Push the A/C button to turn the air condi-
2. Set the air intake control to the outside
position for fan operation.
tioning system on (indicator light will illu-
(fresh) air position.
The fan speed control knob allows you to
minate). Push the button again to turn the
3. Set the temperature control to the
control the fan speed of the air flowing
air conditioning system off.
desired position.
from the ventilation system. To change
4. Set the fan speed control to the
the fan speed, turn the knob to the right
desired speed.
for higher speed or left for lower speed.
5. If dehumidified heating is desired, turn
Setting the fan speed control knob to the
the air conditioning system
(if
“0” position turns off the fan.
equipped) on.
• If the windshield fogs up, set the mode
to the
,
position.
4 78
Features of your vehicle
Operation Tips
D230503AMG
✽ NOTICE
•
To keep dust or unpleasant fumes from
Air conditioning (if equipped)
•
When using the air conditioning sys-
entering the car through the ventilation
All KIA Air Conditioning Systems are
tem, monitor the temperature gauge
system, temporarily set the air intake
filled with environmentally friendly
closely while driving up hills or in
control to the recirculated air position.
R-134a refrigerant which does not dam-
heavy traffic when outside tempera-
Be sure to return the control to the
age to the ozone layer.
tures are high. Air conditioning sys-
fresh air position when the irritation
1. Start the engine. Push the air condi-
tem operation may cause engine over-
has passed to keep fresh air in the
tioning button.
heating. Continue to use the blower
vehicle. This will help keep the driver
2. Set the mode to the
position.
fan but turn the air conditioning sys-
alert and comfortable.
3. Set the air intake control to the outside
tem off if the temperature gauge indi-
•
Air for the heating/cooling system is
cates engine overheating.
air or recirculated air position.
drawn in through the grilles just ahead
•
When opening the windows in humid
4. Adjust the fan speed control and tem-
of the windshield. Care should be
weather air conditioning may create
perature control to maintain maximum
taken that these are not blocked by
water droplets inside the vehicle.
comfort.
leaves, snow, ice or other obstructions.
Since excessive water droplets may
• When maximum cooling is desired, set
•
To prevent interior fog on the wind-
cause damage to electrical equipment,
the temperature control to the extreme
shield, set the air intake control to the
air conditioning should only be run
left position then set the fan speed
fresh air position and fan speed to the
with the windows closed.
control to the highest speed.
desired position, turn on the air condi-
tioning system, and adjust temperature
control to desired temperature.
4 79
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст