KIA Sorento (2018 year). Instruction — part 35
Maintenance
76
7
Description
Fuse rating
Protected component
MEMORY 1
10A
BCM
HEATED
STEERING
15A
BCM
WIPER (RR)
15A
Rear Wiper Relay, Rear Wiper Motor
A/CON 1
7.5A
A/C Control Module, Cluster Ionizer, E/R Junction Block (Blower Relay), ICM Relay Box (Rear Blower Motor
Relay)
HEATED MIRROR
10A
A/C Control Module, Driver/Passenger Power Outside Mirror
MODULE 5
10A
BCM, Smart Key Control Module
MODULE 6
7.5A
Surround View Monitoring Unit, Rear A/C Control Module, Rear Seat Warmer LH, Front Air Ventilation
Control Module, Front Seat Warmer Control Module, AC Inverter Module, Crash Pad Switch
S/HEATER (RR)
15A
Rear Seat Warmer LH
S/HEATER (FRT)
20A
Front Air Ventilation Control Module, Front Seat Warmer Control Module
P/WINDOW (RH)
25A
Rear Safety Power Window RH, Rear Power Window Switch RH, Passenger Safety Power Window Module,
Passenger Door Module, Passenger Power Window Switch
AMP 1
25A
AMP
MODULE 7
7.5A
Gateway (MCU B+), Sport Mode Switch, Key Solenoid, Tire Pressure Monitoring Module
UM USA 7.qxp 3/6/2017 1:45 PM Page 76
7 77
Maintenance
Description
Fuse rating
Protected component
INTERIOR LAMP
10A
Glove Box Lamp, Ignition Key Ill. & Door Warning Switch, Driver Foot Lamp, Vanity Lamp LH/RH Switch,
Cargo Lamp, Center Room Lamp, Overhead Console Lamp, Rear Personal Lamp LH/RH
FUEL LID
10A
Fuel Filler & Tail Gate Switch
P/SEAT (DRV)
30A
Driver IMS Control Module, Driver Seat Manual Switch
P/SEAT (PASS)
30A
Passenger Seat Manual Switch
AMP 2
25A
AMP
P/WINDOW (LH)
25A
Rear Safety Power Window LH, Rear Power Window Switch LH, Driver Safety Power Window Module,
Driver Door Module
MODULE 8
10A
BCM, RAIN SENSOR
UM USA 7.qxp 3/6/2017 1:45 PM Page 77
Maintenance
78
7
Engine compartment fuse panel
OUMA074050
OUM074023
UM USA 7.qxp 3/6/2017 1:45 PM Page 78
7 79
Maintenance
Description
Fuse rating
Protected component
MULTI
FUSE
MDPS 1
100A
MDPS Unit (Rack Type)
MDPS 2
80A
MDPS Unit (Column Type)
COOLING
FAN 1
80A
Cooling Fan 1 Relay
B+1
60A
IGPM (Fuse - S/HEATER (RR), P/SEAT (DRV), P/SEAT (PASS), P/WINDOW (LH))
B+2
60A
IGPM (Fuse - S/HEATER (FRT), P/WINDOW (RH), FULE LID, AMP 1, AMP 2)
B+3
60A
IGPM (IPS 1, Fuse - MODULE 7, Leak Current Autocut Device Fuse - MULTIMEDIA, MEMORY 2,
MEMORY 1), INTERIOR LAMP
B+5
50A
IGPM (IPS 0/IPS 2/IPS 3/IPS 4/IPS 5/IPS 6/IPS 7/IPS 8, Fuse - S/ROOF 1)
FUSE
B+4
40A
IGPM (Fuse - DOOR LOCK, SMART KEY 1, SMART KEY 2, BRAKE SWITCH, A/CON (RR),
S/ROOF 2)
ABS 2
20A
ESC Module
ABS 1
40A
ESC Module, Multipurpose Check Connector
INVERTER
30A
AC Inverter Module
POWER TAIL
GATE
30A
Power Tail Gate Module
TRAILER
30A
Trailer Power Outlet
BLOWER
40A
Blower Relay
UM USA 7.qxp 3/6/2017 1:45 PM Page 79
Maintenance
80
7
Description
Fuse rating
Protected component
FUSE
AMS
10A
Battery Sensor
VACUUM
PUMP
20A
[G4KH] Vacuum Pump
TCU 2
15A
[G4KJ/G4KH] PCM
EPB 1
15A
Electronic Parking Brake Module
EPB 2
15A
Electronic Parking Brake Module
4WD
20A
4WD ECM
ECU 2
15A
PCM
ECU 3
15A
[G6DH] IDB (Injector Driver Box)
MDPS 3
7.5A
MDPS Unit (Rack Type)
TCU 1
10A
Transaxle Range Switch
B/UP LAMP
7.5A
Rear Combination Lamp (IN) LH/RH, BCM, Electro Chromic Mirror, Audio(UVO)
UM USA 7.qxp 3/6/2017 1:45 PM Page 80
7 81
Maintenance
Description
Fuse rating
Protected component
ABS 3
7.5A
ESC Control Module, Multipurpose Check Connector
ECU 1
10A
PCM, [G6DH] IDB (Injector Driver Box)
IG 2
40A
RLY. 4 (Start Relay), PDM (IG2) Relay, Ignition Switch
POWER
OUTLET 1
20A
Front Power Outlet & Cigarette Lighter
SENSOR 6
7.5A
[G4KH] Brake Vacuum Switch, Vacuum Pump
POWER
OUTLET 2
20A
Front Power Outlet
CRUISE
7.5A
Smart Cruise Control Radar
ECU 4
20A
[G4KJ/G4KH] PCM (E-CVVT Relay)
WIPER
25A
Wiper Low Relay
DEICER
15A
Front Deicer Relay
ECU 5
20A
[G4KJ/G4KH] PCM (E-CVVT Relay)
IG 1
40A
PDM (IG1) Relay, PDM (ACC) Relay, Ignition Switch
SENSOR 4
10A
[G4KJ/G4KH] Oxygen Sensor (Up/Down)
[G6DH] PCM, Oxygen Sensor #1/#2/#3/#4
SENSOR 5
15A
[G4KJ/G4KH]PCM
[G6DH] IDB (Injector Driver Box)
UM USA 7.qxp 3/6/2017 1:45 PM Page 81
Maintenance
82
7
Description
Fuse rating
Protected component
POWER
OUTLET 3
20A
Rear Power Outlet
SENSOR 1
20A
[G4KJ/G4KH] Ignition Coil #1/#2/#3/#4 [G6DF] Ignition Coil #1/#2/#3/#4/#5/#6, Condecser #1/#2
SENSOR 3
10A
[G4KJ/G4KH] Fuel Pump Relay [G6DF] Fuel Pump Relay, PCM
POWER
OUTLET 4
20A
Luggage Power Outlet
REAR
HEATED
40A
Rear Defogger Relay
SENSOR 2
10A
[G4KJ/G4KH] E/R Junction Block (Cooling Fan 1 Relay), Oil Control Valve (Exhaust), Purge Control Solenoid
Valve, Canister Close Valve, Variable Intake Solenoid Valve, RCV Control Solenoid Valve (G4KH)
[G6DH] E/R Junction Block (Cooling Fan 1 Relay), Variable Intake Solenoid Valve #1/#2, Purge Control
Solenoid Valve, Oil Control Valve #1/#2/#3/#4 (Intake/Exhaust), PCM, Canister close valve
FUEL PUMP
20A
Fuel Pump Relay
HORN
15A
Horn Relay
B/ALARM
HORN
10A
Burglar Alarm Horn Relay
UM USA 7.qxp 3/6/2017 1:45 PM Page 82
7 83
Maintenance
Relay NO.
Relay Name
Type
E31
Blower Relay
MICRO
E32
START #2 Relay
MICRO
E33
Cooling Fan #1 Relay
MINI
UM USA 7.qxp 3/6/2017 1:45 PM Page 83
Maintenance
84
7
LIGHT BULBS
Please prepare lamps with appropri-
ate standards in case of emergen-
cies. (Refer to chapter 8 for further
information)
When changing lamps and sorts,
first turn off the engine at a safe
place, firmly apply the side brake and
take out the battery’s negative (-) ter-
minal.
Use only the bulbs of the specified
wattage.
✽
✽
NOTICE
• If the light bulb or lamp connector
is removed from an operating
lamp activated by electricity, the
fuse box’s electronic device may
scan it as a malfunction.
Therefore, a lamp malfunction
history may be recorded in
Diagnostic Trouble Code (DTC) in
the fuse box.
• It is normal for an operating lamp
may blink temporarily. Since this
occurrence is due stabilization
function of the vehicle’s electronic
control device, if the lamp lights
up normally after temporary
blinking, there is no problem in
the vehicle.
However, if the lamp continues to
blink several times or turn off
completely, there may be an error
in the vehicle’s electronic control
device. So please have the vehicle
checked by an authorized Kia
dealer immediately.
WARNING
-
Working on
the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switch
is turned to the LOCK position
and turn off the lights to avoid
sudden movement of the vehi-
cle and burning your fingers or
receiving an electric shock.
CAUTION -
Light replace-
ment
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause damage to the fuse
or electric wiring system.
CAUTION -
Headlamp
Lens
To prevent damage, do not
clean headlamp lens with chem-
ical solvents or strong deter-
gents.
UM USA 7.qxp 3/6/2017 1:45 PM Page 84
7 85
Maintenance
If you don’t have necessary tools, the
correct bulbs and the expertise, con-
sult an authorized Kia dealer. In
many cases, it is difficult to replace
vehicle light bulbs because other
parts of the vehicle must be removed
before you can get to the bulb. This is
especially true if you have to remove
the headlamp assembly to get to the
bulb(s).
Removing/installing the headlamp
assembly can result in damage to
the vehicle.
If unauthentic parts or substandard
lights are used when changing lights,
it may lead to fuse disconnection and
malfunction, and other wiring dam-
ages.
Do not install extra lamps or LED to
the vehicle. If supplementary lights
are installed, it may lead to lamp mal-
function and flickering of the lights. In
addition, the fuse box and other writ-
ing may be damaged.
Front lamp bulb replacement
(1) Headlamp(High)
(2) Headlamp(Low)
(3) Turn signal lamp
(4) Side marker lamp
(5) Position lamp
(6) Fog lamp (if equipped)
OUMA074027
OUMA074114
■
Type A
■
Type B
UM USA 7.qxp 3/6/2017 1:45 PM Page 85
Maintenance
86
7
Headlamp bulb
• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids. Never touch the glass with
bare hands. Residual oil may
cause the bulb to overheat and
burst when lit. A bulb should be
operated only when installed in a
headlamp.
• If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
• Wear eye protection when chang-
ing a bulb. Allow the bulb to cool
down before handling it.
WARNING -
HID
Headlamp low beam
(if equipped)
Do not attempt to replace or
inspect the low beam (XENON
bulb) due to electric shock dan-
ger. If the light bulb does not
operate,
have your vehicle
checked by an authorized Kia
dealer.
OXM079200N
WARNING
- Halogen
bulbs
Handle halogen bulbs with care.
• Halogen bulbs contain pres-
surized gas that will produce
flying pieces of glass if bro-
ken.
UM USA 7.qxp 3/6/2017 1:45 PM Page 86
7 87
Maintenance
Headlamp (bulb type) -high/low
1. Open the hood.
2. Remove the headlamp assembly
from the body of the vehicle
3. Remove the headlamp bulb cover
by turning it counterclockwise.
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Remove the bulb by pulling it out.
6. Inset a new bulb into the socket.
7. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
8. Install the headlamp bulb cover by
turning it clockwise.
Turn signal lamp
Follow the steps 1 to 3 from the pre-
vious page.
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket
OUM074108L
Turn signal
OUM074053L
High lamp
Low lamp
UM USA 7.qxp 3/6/2017 1:45 PM Page 87
Maintenance
88
7
6. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
7. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
✽
✽
NOTICE
If bulb will not rotate inside socket,
remove bulb, rotate 180°, and try
again.
Front fog lamp bulbs
(if equipped)
1. Remove the front bumper under
cover.
2. Reach your hand into the back of
the front bumper.
3. Disconnect the power connector
from the socket.
4. Remove the bulb-socket from the
housing by turning the socket
counter clockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock-
wise.
6. Connect the power connector to
the socket.
7. Reinstall the front bumper under
cover.
✽
✽
NOTICE
Always have the headlamp aiming
adjusted after an accident or after
the headlamp assembly is reinstalled
at an authorized Kia dealer.
OUMA074109
UM USA 7.qxp 3/6/2017 1:45 PM Page 88
7 89
Maintenance
Headlamp low (HID), Position
lamp (LED)/Side marker
lamp(LED) replacement
If the light bulb does not operate,
have the vehicle checked by an
authorized Kia dealer.
✽
✽
NOTICE
HID lamps have superior perform-
ance vs. halogen bulbs. HID lamps
are estimated by the manufacturer
to last twice as long or longer than
halogen bulbs depending on their
frequency of use. They will probably
require replacement at some point
in the life of the vehicle. Cycling the
headlamps on and off more than
typical use will shorten HID lamps
life. HID lamps do not fail in the
same manner as halogen incandes-
cent lamps. If a headlamp goes out
after a period of operation but will
immediately relamp when the head-
lamp switch is cycled it is likely the
HID lamp needs to be replaced. HID
lamping components are more com-
plex than conventional halogen
bulbs thus have higher replacement
cost.
Side repeater lamp replace-
ment
If the light bulb does not
operate,have the vehicle checked by
an authorized Kia dealer. A skilled
technician should check or repair the
side repeater lamp, for it may dam-
age related out side mirror parts of
the vehicle.
OUM074028
UM USA 7.qxp 3/6/2017 1:45 PM Page 89
Maintenance
90
7
Rear combination lamp bulb
replacement
Outside lamp
Type A
1. Open the liftgate.
2. Open the service cover.
3. Remove the nuts from the vehicle.
4. Remove the rear combination
lamp assembly from the body of
the vehicle.
OUMA074031
OUM074032
OUM074033
OUM074030L
OUM074029
■
Type A
■
Type B
Stop&tail
Tail
Turn signal
Back up
Turn signal
Back up
Stop&tail
Stop&tail
Side marker
Side marker
UM USA 7.qxp 3/6/2017 1:45 PM Page 90
7 91
Maintenance
5. Disconnect the connector
between lamp and the body.
6. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
7. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
8. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
9. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
10. Reinstall the light assembly to
the body of the vehicle.
* If your vehicle is equipped with LED
type stop and tail lamps replace
with LED assembled units. Please
contact an authorized Kia dealer.
Type B (Stop and tail lamp)
If the lamp bulb does not operate,
have the vehicle checked by an
authorized Kia dealer.
Inside lamp
OUMA074035
OUMA074112
OUM074036
■
Type A
■
Type B
OUM074034
OUMA074111
■
Type A
■
Type B
UM USA 7.qxp 3/6/2017 1:45 PM Page 91
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст