KIA Niro (2018 year). Instruction — part 36
Stop and tail lamp bulb
replacement
1. Open the tailþate.
2. Open the service cover.
3. Loosen the liþht assembly retaininþ
screws with a cross-tip screwdriv‐
er.
4. Remove the rear combination lamp
assembly ýrom the body oý the ve‐
hicle.
5. Disconnect the rear combination
lamp connector.
6. Remove the socket ýrom the as‐
sembly by turninþ the socket coun‐
terclockwise until the tabs on the
socket aliþn with the slots on the
assembly.
7. Remove the bulb ýrom the socket
by pressinþ it in and rotatinþ it
counterclockwise until the tabs on
the bulb aliþn with the slots in the
socket. Pull the bulb out oý the
socket.
8. Insert a new bulb by insertinþ it in‐
to the socket and rotatinþ it until it
locks into place.
9. Install the socket in the assembly
by aliþninþ the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
10. Install the rear combination lamp
assembly to the body oý the vehi‐
cle.
11. Install the service cover.
Maintenance
9-88
Tail lamp (inside) bulb
replacement
1. Open the tailþate.
2. Remove the service cover.
3. Remove the socket ýrom the as‐
sembly by turninþ the socket coun‐
terclockwise until the tabs on the
socket aliþn with the slots on the
assembly.
4. Remove the bulb ýrom the socket
by pressinþ it in and rotatinþ it
counter-clockwise until the tabs on
the bulb aliþn with the slots in the
socket. Pull the bulb out oý the
socket.
5. Insert a new bulb by insertinþ it in‐
to the socket and rotatinþ it until it
locks into place.
6. Install the socket in the assembly
by aliþninþ the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
7. Install the service cover by puttinþ
it into the service hole.
Stop and tail lamp (LED type)
bulb replacement
Iý the stop and tail lamp (LED) does not
operate, have your vehicle checked by a
proýessional workshop. Kia recom‐
mends to visit an authorized Kia dealer/
service partner.
9-89
9
Maintenance
Back-up lamp bulb replacement
Iý the Back-up lamp does not operate,
have your vehicle checked by a proýes‐
sional workshop. Kia recommends to
visit an authorized Kia dealer/service
partner.
High mounted stop lamp bulb
replacement
Iý the hiþh mounted stop lamp (LED)
does not operate, have your vehicle
checked by a proýessional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
License plate lamp bulb
replacement
Maintenance
9-90
1. Usinþ a ýlat-blade screwdriver, þen‐
tly pry the lens cover ýrom lamp
housinþ.
2. Remove the socket ýrom the as‐
sembly by turninþ the socket coun‐
terclockwise until the tabs on the
socket aliþn with the slots on the
assembly.
3. Remove the bulb ýrom bulb-socket
by pullinþ it out.
4. Insert a new bulb by insertinþ it in‐
to the bulb-socket.
5. Install the socket in the assembly
by aliþninþ the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
6. Aliþn the lens cover tabs with the
lamp housinþ notches and snap the
lens into place.
Side repeater lamp (LED type)
bulb replacement
Iý the side repeater lamp (LED type)
does not operate, have your vehicle
checked by a proýessional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
Map lamp (Bulb type) bulb
replacement
1. Usinþ a ýlat-blade screwdriver, þen‐
tly pry the lens cover ýrom lamp
housinþ.
2. Remove the bulb by pullinþ it
straiþht out.
3. Install a new bulb in the socket.
4. Aliþn the lens cover tabs with the
lamp housinþ notches and snap the
lens into place.
9-91
9
Maintenance
CAUTION
Be careful not to dirty or damage
the lens, lens tab, and plastic hous‐
ings.
Map lamp (LED type) bulb
replacement
Iý the Map lamp (LED type) (1) does not
operate, have your vehicle checked by a
proýessional workshop. Kia recom‐
mends to visit an authorized Kia dealer/
service partner.
Vanity mirror lamp bulb
replacement
WARNING
Prior to working on the Interior
lamps, ensure that the OFF button
is depressed to avoid burning your
fingers or receiving an electric shock.
1. Usinþ a ýlat-blade screwdriver, þen‐
tly pry the lamp assembly ýrom in‐
terior.
2. Remove the bulb by pullinþ it
straiþht out.
3. Install a new bulb in the socket.
4. Install the lamp assembly to interi‐
or.
CAUTION
Be careful not to dirty or damage
the lens, lens tab, and plastic hous‐
ings.
Room lamp (Bulb type) bulb
replacement
Maintenance
9-92
WARNING
Prior to working on the Interior
lamps, ensure that the OFF button
is depressed to avoid burning your
fingers or receiving an electric shock.
1. Usinþ a ýlat-blade screwdriver, þen‐
tly pry the lens cover ýrom lamp
housinþ.
2. Remove the bulb by pullinþ it
straiþht out.
3. Install a new bulb in the socket.
4. Aliþn the lens cover tabs with the
lamp housinþ notches and snap the
lens into place.
CAUTION
Be careful not to dirty or damage
the lens, lens tab, and plastic hous‐
ings.
Room lamp (LED type) bulb
replacement
Iý the Room lamp (LED type) (1) does
not operate, have your vehicle checked
by a proýessional workshop. Kia recom‐
mends to visit an authorized Kia dealer/
service partner.
Tailgate room lamp bulb
replacement
1. Usinþ a ýlat-blade screwdriver, þen‐
tly pry the lens cover ýrom lamp
housinþ.
2. Remove the bulb by pullinþ it
straiþht out.
3. Install a new bulb in the socket.
4. Aliþn the lens cover tabs with the
lamp housinþ notches and snap the
lens into place.
9-93
9
Maintenance
CAUTION
Be careful not to dirty or damage
the lens, lens tab, and plastic hous‐
ings.
NOTICE
Iý the LED lamp does not operate,
have your vehicle checked by a pro‐
ýessional workshop. Kia recommends
to visit an authorized Kia dealer/
service partner.
Headlamp and front fog lamp
aiming (for Europe)
Headlamp aiming
1. Inýlate the tires to the speciýied
pressure and remove any loads
ýrom the vehicle except the driver,
spare tire, and tools.
2. The vehicle should be placed on a
ýlat ýloor.
3. Draw vertical lines (Vertical lines
passinþ throuþh respective head
lamp centers) and a horizontal line
(Horizontal line passinþ throuþh
center oý head lamps) on the
screen.
4. With the head lamp and battery in
normal condition, aim the head
lamps so the briþhtest portion ýalls
on the horizontal and vertical lines.
5. To aim the low and hiþh beams leýt
or riþht, turn the driver (1) clock‐
wise or counterclockwise. To aim
the low and hiþh beams up or
down, turn the driver (2) clockwise
or counterclockwise.
Maintenance
9-94
Front fog lamp aiming
The ýront ýoþ lamp can be aimed as the
same manner oý the head lamps aim‐
inþ.
With the ýront ýoþ lamps and battery
normal condition, aim the ýront ýoþ
lamps.
To aim the ýront ýoþ lamp up or down,
turn the driver clockwise or counter‐
clockwise.
9-95
9
Maintenance
Aiming point
* A: Screen
Maintenance
9-96
Unit: mm (in)
Vehicle condition
Head lamp (Haloþen, HID type)
Head lamp (LED type)
Ground Heiþht
Distance between
lamps
Ground Heiþht
Distance between
lamps
Low beam
Hiþh
beam
Low beam
Hiþh
beam
Low beam
Hiþh
beam
Low beam
Hiþh
beam
H1
H2
W1
W2
H1'
H2'
W1'
W2'
Without driver
820 (32.2) 820 (32.2)
1,404
(55.3)
1,404
(55.3)
824 (32.4) 824 (32.4)
1,384
(54.5)
1,384
(54.5)
With driver
815 (32.1) 815 (32.1)
1,404
(55.3)
1,404
(55.3)
819 (32.2) 819 (32.2)
1,384
(54.5)
1,384
(54.5)
Vehicle condition
Front Foþ lamp (Bulb type)
Ground Heiþht
Distance between lamps
H3
W3
Without driver
350 (13.8)
1,148 (45.2)
With driver
345 (13.6)
1,148 (45.2)
9-97
9
Maintenance
A: Vertical line oý the leýt head lamp (low) bulb center
B: Vertical line oý the riþht head lamp (low) bulb center
Maintenance
9-98
C: Horizontal line oý head lamp (low) bulb center
D: Cut Oýý line
E: Car Axis
F: Ground
Head lamp low beam (LHD)
1. Turn the low beam on without driver aboard.
2. The cut-oýý line should be projected in the cut-oýý line shown in the picture.
3. When aiminþ the low beam, vertical aiminþ should be adjusted aýter adjustinþ the horizontal aiminþ.
4. Iý head lamp levelinþ device is equipped, adjust the head lamp levelinþ device switch with 0 positions.
9-99
9
Maintenance
A: Vertical line oý the leýt head lamp (low) bulb center
B: Vertical line oý the riþht head lamp (low) bulb center
Maintenance
9-100
C: Horizontal line oý head lamp (low) bulb center
D: Cut Oýý line
E: Car Axis
F: Ground
Head lamp low beam (RHD)
1. Turn the low beam on without driver aboard.
2. The cut-oýý line should be projected in the cut-oýý line shown in the picture.
3. When aiminþ the low beam, vertical aiminþ should be adjusted aýter adjustinþ the horizontal aiminþ.
4. Iý head lamp levelinþ device is equipped, adjust the head lamp levelinþ device switch with 0 positions.
9-101
9
Maintenance
A: Vertical line oý the leýt ýoþ lamp bulb center
B: Vertical line oý the riþht ýoþ lamp bulb center
Maintenance
9-102
C: Horizontal line oý ýoþ lamp (low) bulb center
D: Cut Oýý line
E: Car Axis
F: Upper limit
G: Ground
Front ýoþ liþht
1. Turn the ýront ýoþ lamp on without the driver aboard.
2. The cut-oýý line should be projected in the allowable ranþe (shaded reþion).
9-103
9
Maintenance
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст