KIA K900 (2018 year). Instruction — part 31
7-84
Maintenance
Engine compartment fuse panel
(Passenger’s side)
✽
NOTICE
Not all fuse panel descriptions in
this manual may be applicable to
your vehicle. It is accurate at the
time of printing. When you inspect
the fuse panel in your vehicle, refer
to the fuse panel label.
OKH075027N
OKH073028N
KH USA 7:2018 4/14/2017 6:39 PM Page 84
Maintenance
7
7-85
Fuse
Fuse Name
Fuse rasting
Circuit Protected
METAL
CORE
BLOCK
(PCB #1)
Sensor 3
10A
Rear Smart Junction Box (Fuel Pump Relay)
P/Door PASS
15A
Passenger Door Latch
SPARE
15A
Spare
Deicer
15A
Metal Core Block (PCB #1) (Front Deicer Relay)
Ignition Coil
20A
Ignition Coil #1~6, Ignition Coil #1~8, Condenser #1, #2
Horn
15A
Metal Core Block (PCB #1) (Horn Relay)
Sensor 2
10A
Mass Air Flow Sensor, Oxygen Sensor #1~4, E/R Fuse & Relay Box LH (RLY.6)
Sensor 4
15A
CMP Sensor #1~4
Wiper 3
30A
Wiper Motor
ECU 3
30A
Metal Core Block (PCB #1) (ECU Main Relay)
ECS 2
40A
Metal Core Block (PCB #1) (Air ECS Relay)
METAL
CORE
BLOCK
(PCB #2)
Sensor 1
15A
Purge Control Solenoid Valve, ECM, Variable Intake Solenoid Valve,
Oil Control Valve #1~4
Injector 2
15A
Injector #1~6, Injector #1~8
SPARE
10A
Spare
SPARE
20A
Spare
SPARE
10A
Spare
KH USA 7:2018 4/14/2017 6:39 PM Page 85
7-86
Maintenance
Fuse
Fuse Name
Fuse rasting
Circuit Protected
METAL
CORE
BLOCK
(PCB #2)
A/CON 2
10A
A/C Control Module
Cruise
10A
Smart Cruise Control Radar
TCU 2
15A
TCM
ECU 2
10A
ECM
Blower
40A
Metal Core Block(PCB) (Blower Relay)
Start 1
30A
E/R Fuse Relay Box LH (RLY.2)
MULTI
FUSE
Preactive Seat
Belt DRV
40A
Driver Seat Belt Pretensioner
Preactive Seat
Belt PASS
40A
Passenger Seat Belt Pretensioner
Battery 2
60A
Smart Junction Box (Fuse : F13~20, F23, F24, F27, F28, IPS5~8, Arisu-LT2)
Battery 1
60A
Smart Junction Box (Fuse : F38, IPS1, 3, Arisu-LT1, Leak Current Autocut Device)
EHPS 2
80A
EHPS Module
FUSE
Battery 4
60A
Metal Core Block (PCB #1) (Fuse : F2, F4, F6, F10, F11, F12)
Battery 5
60A
Metal Core Block (PCB #2) (Fuse : F7, F11)
KH USA 7:2018 4/14/2017 6:39 PM Page 86
Maintenance
7
7-87
Trunk fuse panel
✽
NOTICE
Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of print-
ing. When you inspect the fuse panel in your vehicle, refer to the fuse panel label.
OKH073043N
• Battery box fuse panel
OKH075042N
OKH075041N
KH USA 7:2018 4/14/2017 6:40 PM Page 87
7-88
Maintenance
Fuse Name
Fuse rasting
Circuit Protected
Rear HTD
40A
Rear Defogger Relay
P/WDW RH
30A
Passenger Power Window Module, Rear Power Window Module RH
Power Trunk
30A
Power Trunk Module
Fuel Pump
20A
Fuel Pump Relay
P/Seat RR 1
20A
Rear Seat Relay Box
ECS 1
20A
ECS Unit
P/Seat PASS
15A
Passenger IMS Control Module
P/Door RR RH
15A
Rear Door Latch RH
Spare
15A
Spare
Trunk
10A
Trunk Lid Relay, Power Trunk Module Buzzer
Fog Lamp Rear
10A
Rear Fog Lamp Relay
Spare
40A
Spare
AMP
25A
AMP
Spare
20A
Spare
P/Seat RR 2
10A
Rear Seat Relay Box LH, Rear Seat Relay RH, Rear Seat Massage Control Module LH, Rear Seat Massage
Control Module RH
Spare
10A
Spare
Trunk fuse panel
KH USA 7:2018 4/14/2017 6:40 PM Page 88
Maintenance
7
7-89
Fuse Name
Fuse rasting
Circuit Protected
Door Lock RH
10A
Passenger Door Module, Rear Door Module RH
Door Lock LH
10A
Driver Door Module, Rear Door Latch LH
S/Heater RR
RH
15A
Rear Seat Warmer Control Module RH, Rear CCS Control Module RH
S/Heater RR
LH
15A
Rear Seat Warmer Control Module LH, Rear CCS Control Module LH
Spare
15A
Spare
Fuse Name
Fuse rasting
Circuit Protected
Start 2
40A
Metal Core Block (PCB #2) (Fuse : F8, F9, F12)
AMS
10A
Battery Sensor
Battery 6
100A
Rear Smart Junction Box (Fuse : F1, F2, F3, F4, F5, F6, F7, F8, F10, F11, F13, F15, F17, F18, F19, F20)
Battery box fuse panel
KH USA 7:2018 4/14/2017 6:40 PM Page 89
7-90
Maintenance
LIGHT BULBS
Use only the bulbs of the specified
wattage.
• If you don’t have necessary tools,
the correct bulbs and the expertise,
consult an authorized K900 Kia
dealer. In many cases, it is difficult
to replace vehicle light bulbs
because other parts of the vehicle
must be removed before you can
get to the bulb. This is especially
true if you have to remove the
headlight assembly to get to the
bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.
• Do not install additional bulb or
LED. If you install that, the lamp
may not be operated properly and
fuse box or electric wiring system
may have problem.
✽
NOTICE
After heavy, driving rain or wash-
ing, headlight and taillight lenses
could appear frosty. This condition
is caused by the temperature differ-
ence between the lamp inside and
outside. This is similar to the con-
densation on your windows inside
your vehicle during the rain and
doesn’t indicate a problem with
your vehicle. If the water leaks into
the lamp bulb circuitry, have the
vehicle checked by an authorized
K900 Kia dealer.
Working on the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that Engine Start/Stop
button is in the LOCK position
and turn off the lights to avoid
sudden movement of the vehi-
cle and burning your fingers or
receiving an electric shock.
WARNING
Light Replacement
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause damage to the fuse
or electric wiring system.
CAUTION
KH USA 7:2018 4/14/2017 6:40 PM Page 90
Maintenance
7
7-91
Headlight, front position light,
front turn signal light, front fog
light bulb replacement
(1) Headlight (High)
(2) Headlight (Low)
(3) Front turn signal light
(4) Front position light
(5) Front side marker light
(6) Daytime running light
(7) Front fog light
Headlight bulb
OKH075044N
■
Type A (LED)
OKH073044N
■
Type B (HID)
OKH073081N
Halogen bulbs
Handle halogen bulbs with care.
Halogen bulbs contain pressur-
ized gas that will produce frag-
ment of glass if broken.
WARNING
KH USA 7:2018 4/14/2017 6:40 PM Page 91
7-92
Maintenance
• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.
• Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit.
• If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
• Wear eye protection when chang-
ing a bulb. Allow the bulb to cool
down before handling it.
Headlamp (HID/ LED type), front
position lamp, front turn signal
lamp, front fog lamp
If the light bulb is not operating, have
the vehicle checked by an authorized
K900 Kia dealer.
✽
NOTICE
If your vehicle is equipped with
High Intensity Discharge (HID)
headlights, these headlights contain
mercury. So if you need to have your
vehicle disposed, you should remove
the HID Headlights before disposal.
The removed HID headlights should
be recycled, re-used or disposed as
hazardous waste.
HID Headlight low beam
Do not attempt to replace or
inspect the low beam (XENON
bulb) due to electric shock dan-
ger. If the low beam (XENON
bulb) is not working, have your
vehicle checked by an author-
ized K900 Kia dealer.
WARNING
KH USA 7:2018 4/14/2017 6:40 PM Page 92
Maintenance
7
7-93
✽
NOTICE
HID lamps have superior perform-
ance vs. halogen bulbs. HID lamps
are estimated by the manufacturer
to last twice as long or longer than
halogen bulbs depending on their
frequency of use. They will probably
require replacement at some point
in the life of the vehicle. Cycling the
headlamps on and off more than
typical use will shorten HID lamps
life. HID lamps do not fail in the
same manner as halogen incandes-
cent lamps. If a headlamp goes out
after a period of operation but will
immediately relight when the head-
lamp switch is cycled it is likely the
HID lamp needs to be replaced. HID
lighting components are more com-
plex than conventional halogen
bulbs thus have higher replacement
cost.
Side repeater light bulb
replacement
If the light bulb does not operate,
have the vehicle checked by an
authorized K900 Kia dealer. A skilled
technician should check or repair the
side repeater light, for it may damage
related electrical parts and housing
of outside mirror.
Rear combination light bulb
replacement
(1) Stop and tail light
(2) Rear turn signal light
OKH073031N
OKH075032N
OKH075057N
KH USA 7:2018 4/14/2017 6:40 PM Page 93
7-94
Maintenance
(3) Back-up light
(4) Stop light
(5) Rear side marker light
(6) Reflex reflector
Stop and tail light, Turn signal
light, Back-up light, Rear side
marker light
If the light does not operate, have the
vehicle checked by an authorized
K900 Kia dealer.
High mounted stop light
If the light bulb does not operate, we
recommend the vehicle be checked
by an authorized K900 Kia dealer.
A skilled technician should check or
repair the high mounted stop light,
for it may affect the performance of
the curtain airbags or damage relat-
ed interior parts of the vehicle.
License plate lamp replace-
ment
If the light bulb does not operate, we
recommend the vehicle be checked
by an authorized K900 Kia dealer.
A skilled technician should check or
repair the license plate light, for it
may affect damage related interior
and exterior parts of the vehicle.
OKH073033N
OKH073082N
KH USA 7:2018 4/14/2017 6:40 PM Page 94
Maintenance
7
7-95
Interior light bulb replacement
1.Using a flat-blade screwdriver,
gently pry the lens from the interior
light housing.
2.Remove the bulb by pulling it
straight out.
3.Install a new bulb in the socket.
4.Align the lens tabs with the interior
light housing notches and snap the
lens into place.
5.If the map lamp and room lamp are
not operating, have the vehicle
checked by an authorized K900
Kia dealer.
OKH073036N
OKH075035N
■
Glove box lamp
■
Trunk lamp
Interior Lights
Prior to working on the Interior
Lights, ensure that the “OFF”
button is depressed to avoid
burning your fingers or receiv-
ing an electric shock.
WARNING
Use care not to dirty or damage
lens, lens tab, and plastic hous-
ings.
CAUTION
KH USA 7:2018 4/14/2017 6:40 PM Page 95
7-96
Maintenance
APPEARANCE CARE
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear and
clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits. A mild soap, safe for
use on painted surfaces, may be
used.
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water.
Do not allow soap to dry on the fin-
ish.
• Do not use strong soap,
chemical detergents or hot
water, and do not wash the
vehicle in direct sunlight or
when the body of the vehicle
is warm.
• Be careful when washing the
side windows of your vehicle.
Especially, with high-pressure
water, water may leak through
the windows and wet the inte-
rior.
• To prevent damage to the
plastic parts and lamps, do
not clean with chemical sol-
vents or strong detergents.
CAUTION
KH USA 7:2018 4/14/2017 6:40 PM Page 96
Maintenance
7
7-97
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
while maintaining a slow forward
speed.
High-pressure washing
• When using high-pressure wash-
ers, make sure to maintain suffi-
cient distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors
or its surrounding area directly with
a high pressure washer. Shock
applied from high pressure water
may cause the device to not oper-
ate normally.
• Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be dam-
aged if they come into contact with
high pressure water.
OKH073050N
Wetting Engine
• Water washing in the engine
compartment including high
pressure water washing is not
recommended. It may cause
the failure of electrical circuits
or engine and related part
located in the engine com-
partment.
• Never allow water or other liq-
uids to come in contact with
electrical/electronic compo-
nents and the air duct inside
the vehicle as this may dam-
age them.
CAUTION
KH USA 7:2018 4/14/2017 6:41 PM Page 97
Waxing
A good coat of wax is a barrier
between your paint and contaminate.
Keeping a good coat of wax on your
vehicle will help protect it.
Wax the vehicle when water will no
longer bead on the paint.
Always wash and dry the vehicle
before waxing. Use a good quality
liquid or paste wax, and follow the
manufacturer’s instructions. Wax all
metal trim to protect it and to main-
tain its luster.
Removing oil, tar, and similar materi-
als with a spot remover will usually
strip the wax from the finish. Be sure
to re-wax these areas even if the rest
of the vehicle does not yet need wax-
ing.
Finish damage repair
Deep scratches or stone chips in the
painted surface must be repaired
promptly. Exposed metal will quickly
rust and may develop into a major
repair expense.
✽
NOTICE
If your vehicle is damaged and
requires any metal repair or
replacement, be sure the body shop
applies anti-corrosion materials to
the parts repaired or replaced.
Bright-metal maintenance
• To remove road tar and insects,
use a tar remover, not a scraper or
other sharp object.
• To protect the surfaces of bright-
metal parts from corrosion, apply a
coating of wax or chrome preser-
vative and rub to a high luster.
• During winter weather or in coastal
areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
parts with non-corrosive petroleum
jelly or other protective compound.
Drying Vehicle
• Wiping dust or dirt off the
body with a dry cloth will
scratch the finish.
• Do not use steel wool, abra-
sive cleaners, or strong deter-
gents containing highly alka-
line or caustic agents on
chrome-plated or anodized
aluminum parts. This may
result in damage to the pro-
tective coating and cause dis-
coloration or paint deteriora-
tion.
CAUTION
7-98
Maintenance
KH USA 7:2018 4/14/2017 6:41 PM Page 98
Maintenance
7
7-99
Underbody maintenance
Road salt and other corrosive chem-
icals are used in cold weather states
to melt snow and prevent ice accu-
mulation. If these chemicals are not
regularly removed, they will corrode
the vehicle underbody and over time
damage fuel lines, the fuel tank
retention system, the vehicle sus-
pension, the exhaust system, and
even the body frame. The National
Highway Traffic Safety Administration
has warned all vehicle owners of all
brands of the need to take the follow-
ing steps:
• Wash the undercarriage of your
vehicle regularly during the winter
and whenever your vehicle has
been exposed to such salts or
chemicals.
• Do a thorough washing of the
undercarriage at the end of the
winter.
• Use professional service techni-
cians or governmental inspection
stations to annually inspect for cor-
rosion.
• Immediately seek an inspection of
your vehicle if you become visually
aware of corrosion flaking or scal-
ing or if you become aware of a
change in vehicle performance,
such as soft or spongy brakes, flu-
ids leaking, impairment of direc-
tional control, suspension noises
or rattling metal straps.
Aluminum wheel maintenance
The aluminum wheels are coated
with a clear protective finish.
• Do not use any abrasive cleaner,
polishing compound, solvent, or
wire brushes on aluminum wheels.
They may scratch or damage the
finish.
• Clean the wheel when it has
cooled.
• Use only a mild soap or neutral
detergent, and rinse thoroughly
with water. Also, be sure to clean
the wheels after driving on salted
roads. This helps prevent corro-
sion.
• Avoid washing the wheels with
high-speed car wash brushes.
• Do not use any alkaline or acid
detergent. It may damage and cor-
rode the aluminum wheels coated
with a clear protective finish.
After washing the vehicle, test
the brakes while driving slowly
to see if they have been affected
by water. If braking performance
is impaired, dry the brakes by
applying them lightly while
maintaining a slow forward
speed.
WARNING
KH USA 7:2018 4/14/2017 6:41 PM Page 99
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст